tantric2.718
Harmless
Posts: 9
Registered: 7-1-2017
Member Is Offline
Mood: No Mood
|
|
DIY microwave reactor with integrated stirrer
NOTE TO MODS: i've been away for a while and i accidentally put this in the wrong sub forum, should be in apparatus acquisition.
first, this has nothing to do with plasma or nitric acid. i just need a microwave with a hole in the top for the condenser.
can i use the pre-existing turner mechanism as a magnetic stirrer? it's inset into the bottom of the chamber. i can get a new glass plate that covers
it but doesn't connect then glue teflon covered stirbars to the arms of the turner. it would be slow, but it would be good enough.it would likely work
better if i could get a bunch of stirballs instead of bars.
okay, tell me why this is impossible or tell me how to speed up the turner.
thanks.
[Edited on 4-6-2017 by tantric2.718]
|
|
|
Chemetix
Hazard to Others
Posts: 375
Registered: 23-9-2016
Location: Oztrayleeyah
Member Is Offline
Mood: Wavering between lucidity and madness
|
|
The turning mechanism is driven by a motor that is set to around 8RPM. The only way to speed it up is replace it with something that fits.
I'm uneasy about trying to put holes in the cavity. Wouldn't that just shoot microwave radiation straight up the condenser? Even of you put reflector
mesh in the condenser bore, the glass of the condenser would be wider than the spacing in the reflector mesh and would also leak radiation.
|
|
|
j_sum1
Administrator
Posts: 6320
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
People have put holes in the top of microwave ovens before. It would be worth checking for radiation leaks if you intend to do this. Microwaves are
not to be trifled with.
I would imagine that you could come up with a shielding solution that fits your geometry. It might mean putting some metal mesh in the mouth of your
condenser or creating a curved metal adapter leading from reaction vessel inside to glassware outside.
If you asked, Chemetix could probably make you a glass adapter with embedded mesh that you could use for microwave work. Or maybe you could get away
with silvering a glass straight adapter and plugging it with a mesh to halt straight-through radiation.
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Usual technique is to put a microwave absorber at the top of the opening - graphite block, ferrite block, hell even a container of water would work.
The other way to do it is make the opening into a proper waveguide, with the length adjusted so that the microwaves are reflected back from the open
end. How good is your microwave transmission line theory?
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
tantric2.718
Harmless
Posts: 9
Registered: 7-1-2017
Member Is Offline
Mood: No Mood
|
|
commercial microwaves use a wavelength of 12cm. so long as the hole is less than that in diameter, there will be no leakage. originally i was thinking
of some kind of teflon gasket on the condenser, but now...science! it works, bitches.
[Edited on 5-6-2017 by tantric2.718]
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Actually no - a 1/4 wave hole will act as an antenna. Rule of thumb for shielding is no slots or holes bigger than 1/20 of the wavelength you are
trying to suppress. (I'm an electronic engineer by profession)
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
tantric2.718
Harmless
Posts: 9
Registered: 7-1-2017
Member Is Offline
Mood: No Mood
|
|
i could be totally wrong about all of this...
the radiation from a microwave isn't ionizing/beta.
| Quote: |
Microwave radiation can heat body tissue the same way it heats food. Exposure to high levels of microwaves can cause a painful burn. Two areas of the
body, the eyes and the testes, are particularly vulnerable to RF heating because there is relatively little blood flow in them to carry away excess
heat. Additionally, the lens of the eye is particularly sensitive to intense heat, and exposure to high levels of microwaves can cause cataracts. But
these types of injuries – burns and cataracts – can only be caused by exposure to large amounts of microwave radiation. |
so honestly, what does it matter? if the reactor is in a closet with no metal exposed and condensor threaded through a graphite block and perhaps a
microwave safe bowl hanging over it.....all microwaves at that wavelength can do is burn you.
at what rate are 12cm microwaves absorbed by air? what about just putting a water vaporizer/steam generator pointed above it?
i need this to do is run for 30 to turn apiole into isoapiole.
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
They're not. Apart from the usual inverse square law (power density is inversely proportional to the square of the distance to the source) microwaves
travel quite happily through air for long distances.
Your wifi wouldn't work very well otherwise.
I guess what we're all trying to say is make sure you reduce the risk as much as possible. Take all precautions - don't get hurt.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
Sulaiman
International Hazard
Posts: 3695
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I have a little experience with microwaves,
. a hole the size of a condenser certainly would leak microwaves
. a hole about 1/4 wavelength long (e.g. copper tube) should reflect most of the microwaves back into the cavity.
Also, I would want a Claisen adapter or similar in the hole to allow temperature measurement.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
VSEPR_VOID
National Hazard
Posts: 719
Registered: 1-9-2017
Member Is Offline
Mood: Fullerenes
|
|
You could test for the presents of microwaves leaking from the hole you drill with water or metal power.
|
|
|
Texium
|
Thread Moved
27-11-2023 at 11:34 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
