RogueRose
International Hazard
Posts: 1594
Registered: 16-6-2014
Member Is Offline
|
|
Boiling point of oils (vegetable & motor mostly)
I haven't found any listings for boiling points of oils but have found smoke point, flash point and auto-ignition point.
The reason I'm asking is looking at heating oil in a copper or steel tube as it feeds an oil burner. I'm concerned that the tube will be heated too
much (say 600-1,000F maybe more in extreme points) and something catastrophic would happen in the tubing or feed resevoir.
Ideally the oil would be as hot as possible when it reaches the air stream to achieve auto-ignition when contacting the air stream.
I'm also concerned about other reactions with the oil at high temps like some kind of polymerization (or something that may gum up the flow). IDK if
it needs air to change molecularly..
|
|
|
Deathunter88
National Hazard
Posts: 519
Registered: 20-2-2015
Location: Beijing, China
Member Is Online
Mood: No Mood
|
|
Quote: Originally posted by RogueRose  | I haven't found any listings for boiling points of oils but have found smoke point, flash point and auto-ignition point.
The reason I'm asking is looking at heating oil in a copper or steel tube as it feeds an oil burner. I'm concerned that the tube will be heated too
much (say 600-1,000F maybe more in extreme points) and something catastrophic would happen in the tubing or feed resevoir.
Ideally the oil would be as hot as possible when it reaches the air stream to achieve auto-ignition when contacting the air stream.
I'm also concerned about other reactions with the oil at high temps like some kind of polymerization (or something that may gum up the flow). IDK if
it needs air to change molecularly.. |
Why are you burning motor oil in a oil burner?
|
|
|
Jstuyfzand
Hazard to Others
Posts: 166
Registered: 16-1-2016
Location: Netherlands
Member Is Offline
Mood: Learning, Sorta.
|
|
| Quote: Originally posted by Deathunter88 | | Quote: Originally posted by RogueRose | I haven't found any listings for boiling points of oils but have found smoke point, flash point and auto-ignition point.
The reason I'm asking is looking at heating oil in a copper or steel tube as it feeds an oil burner. I'm concerned that the tube will be heated too
much (say 600-1,000F maybe more in extreme points) and something catastrophic would happen in the tubing or feed resevoir.
Ideally the oil would be as hot as possible when it reaches the air stream to achieve auto-ignition when contacting the air stream.
I'm also concerned about other reactions with the oil at high temps like some kind of polymerization (or something that may gum up the flow). IDK if
it needs air to change molecularly.. |
Why are you burning motor oil in a oil burner? |
Its quite common, lots of people use waste oil burners, either homemade or commercial to melt metals in a foundry.
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
Some high MW organic molecule are subject to cracking and decomposition reaction before reaching boiling point...
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
Texium
|
Thread Moved
13-8-2016 at 18:52 |
NEMO-Chemistry
International Hazard
Posts: 1559
Registered: 29-5-2016
Location: UK
Member Is Offline
Mood: No Mood
|
|
Are you going to centrifuge it first? it tends to give better results, the local garage has a torpedo heater they run off the waste oil they get. They
have a cheap ebay centrifuge they use first and dont pre heat.
I hang around there on occasion looking for aluminium engine heads etc  .
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
