Electra
Hazard to Others
Posts: 179
Registered: 11-12-2013
Member Is Offline
Mood: No Mood
|
|
Is there a way to setup a rotovap so it condenses back into the main flask? An adapter of some kind?
I've been wanting to invest in a rotovap for a while, and lately I've been needing to deal with some reactions that normal stirring(magnetic or
mechanical) wouldn't be ideal. As an alternative, if I could find a way to rotate the flask for the reaction I am doing, it would really simplify
things.
There are plenty of laboratory flask rollers/rotators, but none of them that I'm aware of enable the attachment of a condenser. If I could find a way
to make a rotovap condense back into the main flask, then it could serve a double purpose, reaction followed by solvent removal.
Is there any sort of adapter or attachment that can enable this? I would assume so, I just have no idea what it would be called.
|
|
|
Zephyr
Hazard to Others
Posts: 341
Registered: 30-8-2013
Location: Seattle, WA
Member Is Offline
|
|
This thread seems to recommend against it, citing that rotovaps are quite delicate and refluxes are easy to perform without one. I'd recommend just
taking off the condenser when the reflux is finished and then transitioning to the rotovap: http://www.sciencemadness.org/talk/viewthread.php?tid=18459
That being said, bahamuth does have a nice rotovap reflux setup in the above thread, and this could be the necessary piece: http://www.meadowshplc.com/products/buchi-rotary-evaporators...
Too expensive for me though...
|
|
|
Electra
Hazard to Others
Posts: 179
Registered: 11-12-2013
Member Is Offline
Mood: No Mood
|
|
The issue I have is that I have a large heterogeneous mass inside of a homogenous solution. I can't reflux it because the mass clumps together and
pressure will build up underneath it and then erupt upwards, spewing mess everywhere violently, which I learned the hard way. Stir-bar's wouldn't be
effective and a mechanical stirrer would only work if it could scrape the sides of the flask. What would work is if the flask was rotating to prevent
pockets of the solution from getting trapped under the mass.
[Edited on 20-4-2016 by Electra]
|
|
|
Oscilllator
National Hazard
Posts: 659
Registered: 8-10-2012
Location: The aqueous layer
Member Is Offline
Mood: No Mood
|
|
Just tilt the rotavap over until the flask is vertical 
|
|
|
gsd
National Hazard
Posts: 847
Registered: 18-8-2005
Member Is Offline
Mood: No Mood
|
|
LOL nice one! But what happens to the heating bath?
gsd
|
|
|
BromicAcid
International Hazard
Posts: 3248
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Get the tiniest flask that will fit on your outlet and pre-filll it with your solvent. On the rotovap models that I have seen when your takeoff flask
is full the distillate will shortly (after it fills a few more aberrations) begin flowing back into the flask.
|
|
|
Ozone
International Hazard
Posts: 1269
Registered: 28-7-2005
Location: Good Olde USA
Member Is Offline
Mood: Integrated
|
|
Mine is actually setup for this. There is a valve that shuts off condensate flow to the collection flask (so, it runs back into the pot).
O3
-Anyone who never made a mistake never tried anything new.
--Albert Einstein
|
|
|
Dr.Bob
International Hazard
Posts: 2736
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I use a rotovap for mixing and heating solutions occasionally, great for heating recrystallizations to dissolve the material safely. Just don't cool
the condenser, and set the water bath temp just below the BP, leave the vacuum off, use a keck or other clip to hold the flask on, and it will act as
a rotating heater just fine. As long as the temp is just below the BP and the vacuum is off, the amount of solvent loss is not that much. You
really don't need anything special. If you wanted to do this for hours, you could certainly fill the receiver with solvent, and that would work, but
I've never done one that needed that type of fix.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
