bridgetender26
Harmless
Posts: 2
Registered: 21-12-2015
Member Is Offline
Mood: No Mood
|
|
Mantle with no heat?
Hello,
I am a new member and just starting out with my practice. I am trying to track down a hemispherical mantle with no heating element for a 1L round
flask. I have a magnetic stir plate that I am using for the heat but would like to put the bottom half of my flask into a fiberglass jacket to keep it
evenly heated.
Does this type of product exist? What would you do?
Thanks in advance.
|
|
|
Bert
Super Administrator
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
What kind of temperatures are you intending to run the flask at.
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
|
bridgetender26
Harmless
Posts: 2
Registered: 21-12-2015
Member Is Offline
Mood: No Mood
|
|
Up to 225C
|
|
|
User123
Harmless
Posts: 40
Registered: 31-10-2015
Member Is Offline
Mood: No Mood
|
|
You can get solid blocks of iron which are flask-shaped and designed to go on top of a hotplate/stirrer to act as a heating mantle. I don't know if
they are made for one litre flasks, though. Nor do I know what they are called. But they exist -- I've used them.
|
|
|
Bert
Super Administrator
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
How about a bath full of Aluminum 6mm shot for the bottom half of the flask, and some cheap fiberglass insulation for the top.
http://m.ebay.com/itm/Premium-5K-5000rds-ct-Aluminum-6mm-BBs...
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
|
Dr.Bob
International Hazard
Posts: 2736
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
The mantle would insulate the flask from the heat of the hotplate, and might even get burned. They do make bottom and top type heating mantles, that
can be used for heating flasks to high temps.
http://www.glascol.com/product/subproduct/id/106
If you are planning to heat up to 225, then a mantle should be able to work, but I don't like to take them much above that point. You could also use
high temp oil, BBs, or a metal heating block. Metal blocks work well at those higher temps, I have used Al heating blocks up to 300C.
[Edited on 22-12-2015 by Dr.Bob]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
