Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
DIY geiger tube?
Why isn't anybody making their own tubes? I've searched around and could only find one such build: http://ki3u.byethost3.com/Radio-PhysicsDIR/homemade_GEIGER-T...
I get that they aren't that expensive, but at the same time people seem to make almost anything there is for the fun& challenge of it. So why not
geiger tubes? From what I've read they shouldn't be that hard to construct, so what am I missing?
We're not banging rocks together here. We know how to put a man back together.
|
|
gammainspector
Harmless
Posts: 19
Registered: 19-6-2015
Member Is Offline
Mood: No Mood
|
|
In my opinion, a geiger tube is really only useful when surveying for uranium (and not the best tool for the job) or for after a radiation release.
Most of the "geiger counters" you see out there are either Civilian Defense units or pancake friskers. Neither of them are designed to monitor
airborne radiation levels or in food products.
They aren't super sensitive, they tend to overload, they also don't have a linear response (they over-under respond based on energy of photon) .
I think the better question is, why aren't people building more scintillation counters with BGO or other cheap scintillation crystals that would be
much more sensitive and produce data that would be useful scientifically?
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
My use would be mineral detection, I live not too far from an old mine containing uranium and thorium. Would be fun to have a crude detector that
could give some relative measurements, and since the physics isn't that complex I figured there would be lots of info on this out there.
We're not banging rocks together here. We know how to put a man back together.
|
|
gammainspector
Harmless
Posts: 19
Registered: 19-6-2015
Member Is Offline
Mood: No Mood
|
|
Ok then I would suggest also you consider the 2" Mica window design instead of the tube design. The performance will be better.
They can be built, there is a seller on ebay "GeoElectronics" who can sell you one or the parts to build one, just send him a message and tell him LH
sent you.
[Edited on 4-9-2015 by gammainspector]
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
The structural parts shouldn't be a problem, I have access to both a lathe and a mill. But the lack of DIY-builds makes me wonder if I'm missing
something. If it's as simple as I thought (and the link suggests), why aren't people doing this? I can't be the only one who'd get a kick out of a
homemade geiger tube? I've seen people making radio tubes for pete's sake...
We're not banging rocks together here. We know how to put a man back together.
|
|
bobm4360
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 59
Registered: 18-4-2011
Location: On a wretched little island.
Member Is Offline
Mood: No Mood
|
|
John Strong's "Procedures in Experimental Physics" at the Internet Archive has all you need to make a Geiger-Muller tube, and many other processes
that are useful in more than physics.
Bob
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Excellent find there, I simply LOVE these old books. Good, concise information for DIY experiments, everything an inquiring mind needs to get himself
in trouble
We're not banging rocks together here. We know how to put a man back together.
|
|
neptunium
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 987
Registered: 12-12-2011
Location: between Uranium and Plutonium
Member Is Offline
|
|
electronic sensors for the evil genius by Tom Petruzzellis has one such crude counter
http://www.amazon.com/Electronics-Sensors-Evil-Genius-Electr...
no you are neither the only one nor the first...
Besides a good challenge is always fun and even if you dont make it the learning experience is irreplaceable..
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
This seems quite doable, all things considered. I also found this introduction on GM's: https://www.orau.org/ptp/collection/GMs/introgms.htm
The really interesting bit is the "density thickness" for thin walled tubes and mica windows. I assume penetration mainly depends on the mass and not
the materials themselves, so wouldn't plastics be a suitable candidate for the window? I have some mylar (BoPET) that weighs in at appr 2,5mg/cm^2,
getting it to support a reduced atmosphere (1/10 atm seems common) shouldn't be harder than making multiple small holes.
All I really need for testing is a variable DC supply capable of 1-1,5kV and some radioactive material, an oscilloscope should be able to read the
pulses.
Edit: It's not easy finding reliable data for mylar shear strength, but I found some listing it to 15MPa for 5mil and 13,6MPa for 10mil. That's a far
cry from the 250MPa listed for grade V-1 mica, but it's not too bad really. My sheet is 1mil, so assuming 15MPa (probably higher) and a safety
factor of 3 I get a maximum window size of 4mm for full vacuum.
[Edited on 5-9-15 by Fulmen]
We're not banging rocks together here. We know how to put a man back together.
|
|
careysub
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
Quote: Originally posted by Fulmen ![](images/xpblue/lastpost.gif) | It's not easy finding reliable data for mylar shear strength, but I found some listing it to 15MPa for 5mil and 13,6MPa for 10mil. That's a far cry
from the 250MPa listed for grade V-1 mica, but it's not too bad really. My sheet is 1mil, so assuming 15MPa (probably higher) and a safety factor of
3 I get a maximum window size of 4mm for full vacuum.
|
Stainless steel sifting screens of 5 mesh have 4 mm apertures, and 10 and 20 mesh screens (which I found easily on eBay at modest cost) are 2 mm and
0.85 mm. That would seem to be a good support for a mylar window.
|
|
mayko
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1218
Registered: 17-1-2013
Location: Carrboro, NC
Member Is Offline
Mood: anomalous (Euclid class)
|
|
I didn't see any projects which specifically built the tube, but the Hack-a-Day geiger counter projects are pretty cool.
al-khemie is not a terrorist organization
"Chemicals, chemicals... I need chemicals!" - George Hayduke
"Wubbalubba dub-dub!" - Rick Sanchez
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Mesh screens would probably work, but getting a good seal could be a problem. Probably nothing a bit of epoxy wouldn't fix.
We're not banging rocks together here. We know how to put a man back together.
|
|
Fulmen
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1702
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
The key to a good, fast tube seems to lie in the quenching. Not sure how fast you'd need a tube for casual prospecting, and even slow tubes should
count 10-100/s so I don't think one needs to worry too much about it for a proof of concept.
This patent seems to contain a lot of useful information: http://www.google.com/patents/US4501988
We're not banging rocks together here. We know how to put a man back together.
|
|
Romix
Hazard to Others (Literally)
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 455
Registered: 19-6-2015
Member Is Offline
Mood: No Mood
|
|
Very interesting thread.
Can Geiger tube operate of the battery with led diode?
Is there specific current to go through the tube? Is it different to brands and models?
Need it to test valves for thorium. And broken X-ray guns, there's two powders one grey one white.
I heated one wire covered in it, and inhaled the smoke, it gave me heart kick. And oxide turned yellow.
Last time I opened container in which it is stored. It gave me a heart kick again. Possibly radioactive.
It's under my bed, where I sleep. Is it safe??
![553e51047a45.jpg - 141kB](https://www.sciencemadness.org/whisper/files.php?pid=444182&aid=49623)
[Edited on 3-4-2016 by Romix]
[Edited on 3-4-2016 by Romix]
|
|
Heavy Walter
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 127
Registered: 17-12-2015
Location: Argentina
Member Is Offline
Mood: No Mood
|
|
Romix
The picture shows CRT guns.
Powering the filament at open air oxidized the tungsten wire and you got the yellow oxide. They are supposed to be powered under vacuum.
No radiation risk.
|
|
Radium212
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
Try H.V Neher's 1938 book, "Building and using Geiger counters". It's got all the instructions you need. You can find it on Etsy or AbeBooks.
|
|
Radium212
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 85
Registered: 26-6-2017
Member Is Offline
Mood: Pyrophoric.
|
|
Quote: Originally posted by Romix ![](images/xpblue/lastpost.gif) | Very interesting thread.
Can Geiger tube operate of the battery with led diode?
Is there specific current to go through the tube? Is it different to brands and models?
Need it to test valves for thorium. And broken X-ray guns, there's two powders one grey one white.
I heated one wire covered in it, and inhaled the smoke, it gave me heart kick. And oxide turned yellow.
Last time I opened container in which it is stored. It gave me a heart kick again. Possibly radioactive.
Where did you get all those CRT guns ?![:D](./images/smilies/biggrin.gif)
It's under my bed, where I sleep. Is it safe??
[Edited on 3-4-2016 by Romix]
[Edited on 3-4-2016 by Romix] |
|
|