UncleJoe1985
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 88
Registered: 30-9-2008
Location: Sunnyvale, CA
Member Is Offline
Mood: No Mood
|
|
help! lead contamination
Crap, I just messed up big time. I was making lead acetate to make PbO2 anodes by mixing PbO and acetic acid. Except I left the hot plate
on for too long, causing it to decompose into this monstrosity ![:o](./images/smilies/shocked.gif)
![20150412_042023.jpg - 3.5MB](https://www.sciencemadness.org/whisper/files.php?pid=400799&aid=38947)
The hot plate temperature was set to 450F and left on for 2 hours. I guess the solution was already saturated at the beginning with about 160g
Pb(CH3COO)2.
I had no idea lead acetate would decompose and generate PbO fumes or else I would've done it outside. Now my bathroom stinks with some bitter smell
(not sure how to describe it exactly). How bad do you guys think it is and how should I go about decontaminating it?
|
|
blogfast25
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
The level of contamination is probably quite low because most lead compounds are non-volatile. But droplets carrying lead compounds may have escaped
the solution/slurry and ended up on the walls etc of your bathroom. Since as we don't actually know the level of contamination I would take ZERO
chances here.
At a very minimum, wearing decent marigold gloves, sponge EVERYTHING down with soapy water, dry with kitchen towel or such like, then rinse with clean
water and dry again. Any carpet should be thoroughly vacuumed. Anything like towels and the stuff used for the clean up I'd dispose of to be on the
safe side.
Dealing with such quantities of lead based compounds in a domestic dwelling was never a smart idea to begin with, so learn from the experience.
[Edited on 12-4-2015 by blogfast25]
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Most of your decomposition smell is probably from the acetic acid rather than lead. As blogfast suggested wipe everything down. Most lead salts are
really insoluble. The nitrates and the acetates being the exceptions. After cleaning everything you should sprinkle baking soda over everything
which should convert any soluble lead salts to insoluble carbonates. You will need to either use a wet solution of baking soda or let it sit long
enough for atmospheric moisture to work on it. Then vacuum up the baking soda. You should get the area where you were working tested for lead
contamination after the clean up. And you are required by law to disclose such contamination to your landlord and/or future purchasers of the
property if you live in the US and contamination is found.
[Edited on 12-4-2015 by macckone]
|
|
violet sin
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1476
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
I would say: sponge TSP cleaner on all surfaces, in my experience there is *always* at least a a small layer of oil/dirt on the walls of an inhabited
dwelling. release of this from the wall will hopefully dilute and contain the lead if any was present, but will definitely clean a lot better than
soap and water. pre/post treatment with an ozone machine would deff help the smell and possibly oxidizing the lead if any was still there as the
acetate.
@ macckone: don't forget about the sulfamate salt for soluble lead compounds ![:)](./images/smilies/smile.gif)
re-rocking (drywall) the bathroom would be fairly easy if you are capable; nice small room, only take a couple days short of repainting. if you clean
the walls with a partially damp sponge and try to squeeze the residue into a container for testing, it would help to know if you just clean and call
it good, paint over it, or deeper remediation like stripping the walls out.
save the solution, evaporate, leach with either sulfamic/acetic/nitric acid, and try to plate out the lead with small graphite electrodes( easier to
see and insoluble).
obviously none of this came from a hazmat book, or lab procedure... and isn't a strictly legal protocol. but more from actual life experience, and
what I would think might be workable. I do drywall for a living, so I clean walls regularly for remodels. standard soap and water is almost useless
for me in that regard. for a small bathroom 8' x 8', you are probably looking at 200$ materials, + tools if you don't own them + a lot of frustration
if you are new to it. but it would be substantially more to pay some one to do it for you in most cases. ~600$ around here depending on texture
style, more or less based on where you are located.
-VioletSin-
|
|
UncleJoe1985
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 88
Registered: 30-9-2008
Location: Sunnyvale, CA
Member Is Offline
Mood: No Mood
|
|
Quote: |
The level of contamination is probably quite low because most lead compounds are non-volatile
|
Whew, that's a relief. Thanks everyone for their advice.
I'll never do that again in a residential area.
I understand the benefit of converting soluble lead compounds into insoluble ones to make it harder to get absorbed into your body. But then why all
the fuss over lead paint, which contains insoluble lead carbonate and chromate. Is that fear mongering?
I'll try using TSP, but it seems to be doing the same thing as soap by dissolving oil that the lead might stick to. Vaguely, saponification seems more
effective since it actively dissolves the oil instead of passively dissolving it like soap?
Quote: | Save the solution, evaporate, leach with either sulfamic/acetic/nitric acid, and try to plate out the lead with small graphite
|
I'll try that too. But I don't think leaching will work because it will dissolve the TSP too. I think you mean to leach the TSP out with water, then
dissolve the remaining insoluble lead in acid? Or does it not matter if you have TSP in the electrolyte?
I'm thinking about getting a lead test kit, but it says consumer ones only have a threshold of 2000ppm, well above the safe levels for long term
contact, and not anywhere near the level for drinking water (15 ppb). I'll get one anyways and test it on the waste water I collect.
|
|
violet sin
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1476
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
nah, I meant to evaporate the solution to wax, oil, dirt, TSP( sodium metasilicate), prob sodium carbonate, lead acetate(?), lead carbonate(?), lead
oxides(?) and a few others like maybe titanium dioxide from the paint. but the dried cake would only have sodium and maybe lead that would leach out
with the acid extraction. personally I would use sulfamic acid, but I just like the stuff and have it on hand. when filtered and reduced in volume
to electroplate it out on the graphite, only lead would plate out. the sodium would just be present as a spectator for the most part, other than
maybe changing the pH.
sulfamic acid works great for electroplating lead. I have a bunch of papers on it, alas that mother board on that PC recently took ill, and the hard
drives are waiting for a full desktop PC transplant... I have been left with the pittance of papers and patents I had dupes of on the lap top until
the other one gets back from the shop
but a bought test seems WAY easier and and quantifiable. where the electrolysis would be more for curiosity and a rudimentary test that would have to
be conducted with incredibly small electrode surface area in order to see a coating or crystals. and you would have to save as much of the solution
as poss to see anything if it is a really low concentration, if at all.
|
|
jock88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 505
Registered: 13-12-2012
Member Is Offline
Mood: No Mood
|
|
Wash the place down with a soluble sulphite if you can get one. Lead Sulphite is the least soluble of lead compounds. Sulphate is probably next
best.
Lead is particularly dangerous to young things (animals and children).
|
|
blogfast25
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by jock88 ![](images/xpblue/lastpost.gif) |
Wash the place down with a soluble sulphite if you can get one. Lead Sulphite is the least soluble of lead compounds. Sulphate is probably next
best.
Lead is particularly dangerous to young things (animals and children). |
I think you meant sulph<b>ide</b>. As in PbS (lead sulphide). Water soluble sulphides stink of H<sub>2</sub>S though.
|
|
jock88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 505
Registered: 13-12-2012
Member Is Offline
Mood: No Mood
|
|
Indeed I did, sorry about that.
Are there any common uses for a soluble 'xxx' sulphide sale or a soluble 'xxx' hydrogen sulphide salt?
Where might you purchase them OTC.
What happens when you mix a solution of soluble Lead compound and sodium Sulphite (thats sulphite not sulphide)
[Edited on 14-4-2015 by jock88]
|
|
violet sin
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1476
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
liver of sulfur for aging silver and copper is a mix of pollysulfides as far as I know.
"Liver of Sulfur is a poorly defined mixture of potassium sulfide, potassium polysulfide, potassium thiosulfate, and probably potassium bisulfide."
http://en.wikipedia.org/wiki/Liver_of_sulfur
https://www.youtube.com/watch?v=30hEhFJ8Ejc
youtube vid of making it, not in english though.
|
|
AJKOER
Radically Dubious
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
On the thermal decomposition of Lead acetate, to quote from one source (see page 5 at https://www.google.com/url?sa=t&source=web&rct=j&... ):
"The products from the acetoxy radical were found to be mainly C02 and methyl acetate by vapor phase infrared spectroscopy. Ethane, if formed, must be
present in small proportions."
The author also further details the different reactions in the thermal decomposition of Lead acetate.
Now, with respect to methyl acetate (MA), Wikipedia comments ( see http://en.m.wikipedia.org/wiki/Methyl_acetate ):
"Methyl acetate is occasionally used as a solvent, being weakly polar and lipophilic, but its close relative ethyl acetate is a more common solvent
being less toxic and less soluble in water. Methyl acetate has a solubility of 25% in water at room temperature. "
and also:
"A major use of methyl acetate is as a volatile low toxicity solvent in glues, paints, and nail polish removers."
Wikipedia also notes that MA is more soluble in a strong base, so you may wish to try Washing Soda and not NaHCO3.
[Edited on 6-5-2015 by AJKOER]
|
|