Magpie
lab constructor
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
FIRE IN THE HOOD!
A forum member asked me if I have ever had a fire in my hood, and if so, did I turn the fan off or leave it on.
I have had a phosphorus fire that nearly overwhelmed my powerful fan (~400 cfm). I left the fan ON as otherwise my garage would have been filled with
P2O5 smoke. It was a bit concerning to see white smoke billowing out of the vent in the peak of my garage, but otherwise not a fire risk. I was just
hoping the neighbors wouldn't see it and call the fire department. It lasted less than 1 minute.
On the other hand I've never had a solvent fire in my hood. I keep a dry chemical fire extinguisher and a bucket of sand handy, and I would quickly
use them. But would I leave the fan ON, or turn it OFF? On the one had you would want to move all that smoke out of your hood and lab. But on the
other hand the fan is feeding the fire fresh oxygen and potentially carrying the flame into the PVC ducting. I really haven't thought this through
very well.
What would you do, and why?
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3632
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
1) change my trousers
2) close the hood if possible, preventing fresh oxygen and trapping the CO2
3) turn the fan off .... sucking flames up the vent may cause a wiring short so better if no power available.
4) tidy up and pretend it never happened
|
|
Molecular Manipulations
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 447
Registered: 17-12-2014
Location: The Garden of Eden
Member Is Offline
Mood: High on forbidden fruit
|
|
For a solvent fire or any substance that burns to produce non-toxic gasses like carbon dioxide, water and nitrogen, I'd leave the fan off to keep it
from burning the fan, which is mostly plastic. If/when I have sulfur, phosphorus or something that burns to make a toxic oxide I'd leave/turn the fan
on. I've never had a bad fire in my hood (because I made it recently, and haven't really used it much). All my fires where before I had a hood, and
most where outside.
I did have one really bad fire, which started by itself while I was gone. It ruined at least $100 worth of reagents and left a lot of soot in my lab,
no equipment was destroyed though, because it happened in one of my chemical storage cabinets. To this day I don't know what started the fire, but I
think it may have been iodine trichloride (I2Cl6) because it a hole was burned through the plastic lid, and all of it was gone
because the glass cracked.
-The manipulator
We are all here on earth to help others; what on earth the others are here for I don't know. -W. H. Auden
|
|
aga
Forum Drunkard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
The smart-ass reply would be :
Think things through, and arrange things so that an Uncontrolled fire was not possible.
I have not had an uncontrolled fire yet.
My attitude will likely change if i do.
|
|