Sniffity
Hazard to Self
Posts: 70
Registered: 27-12-2014
Member Is Offline
Mood: No Mood
|
|
Why use Mineral Oil for Alkalis?
I understand, perfectly well, that mineral oil prevents water from mixing with alkalie metals when they're stored under it.
But here's my question: In theory, a mineral oil will have two or so oxygen atoms, around the glycerol head. Isn't there a slightest possibility of
some of this oxygen atoms reacting with the metals? Say, if some very small amount of water vapour was to come into contact with the alkali, form a
hydroxide, this could proceed as an alkali hydrolysis?
Under this logic, isn't a hydrocarbon better for storage? Say, hexane, or even common gasoline?
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
I believe that mineral oil is used because oxygen is very poorly soluble in it. Don't quote this.
I'd much rather use an inert material such as xylene to store sodium, because it's easier to remove. I looked up the solubility of oxygen in the
xylene isomers, and it's very slightly soluble. I couldn't find the data for mineral oil. I'm sure it's close at hand, but I'm too lazy to look for it
at the moment.
[Edited on 21-1-2015 by Awesomeness]
Fear is what you get when caution wasn't enough.
|
|
|
Crowfjord
Hazard to Others
Posts: 390
Registered: 20-1-2013
Location: Pacific Northwest
Member Is Offline
Mood: Ever so slowly crystallizing...
|
|
@Sniffity: You're thinking of fat, i.e. oil from a biological source. Mineral oil is derived from petroleum and has no glycerol "backbone." Mineral
oil is mostly very long alkane chains, I believe. It is indeed a hydrocarbon, but non-volatile, unlike hexane, heptane, etc.
[Edited on 21-1-2015 by Crowfjord]
|
|
|
IrC
International Hazard
Posts: 2710
Registered: 7-3-2005
Location: Eureka
Member Is Offline
Mood: Discovering
|
|
I think the important factors are it's cheap, readily available, works very well to protect O2 reactive metals, and is fairly stable over a long time.
I use mineral oil for many metals in the rare earth and alkaline series, and my U238. Never had a problem yet.
"Science is the belief in the ignorance of the experts" Richard Feynman
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I have some sodium under mineral oil for 5 years now, and it still looks kind of shiny.
It is under nitrogen and unopened though.
[Edited on 21-1-2015 by Tsjerk]
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
First result on google. That wasn't hard...
http://www.jbc.org/content/72/2/545.full.pdf+html
I'm planning to get some sodium, so I'll put some of it under xylene in an OXYGEN atmosphere and see how it does.
Fear is what you get when caution wasn't enough.
|
|
|
Praxichys
International Hazard
Posts: 1063
Registered: 31-7-2013
Location: Detroit, Michigan, USA
Member Is Offline
Mood: Coprecipitated
|
|
Yes, storing reactive metals under triglycerides (oils from animal or vegetable sources) would be very bad. You would make soap almost immediately
when the metal tears the fatty acids from the glycerol backbone.
Mineral oils, as mentioned above, contain no such backbone, and come from the ground. They are straight alkanes from C15-C60 depending on the grade.
Typically oil is used for a number of reasons. Pretty much all nonpolar oils will dissolve very little oxygen. Xylene, toluene, benzene, and lighter
naphtha fractions (like camp fuel or gasoline) will all work, but the oil has several advantages:
1. The oil forms a viscous film and does not evaporate, so when handling bigger samples the protection from air is better. Xylenes or lighter fluid
will eventually evaporate form the surface, leaving bare metal exposed to air during cutting and handling operations. Oil also has no odor and reduces
exposure to solvent vapors.
2. Mineral oil is difficult to ignite. Accidents happen, and even a tiny bit of accidental moisture on something can create a spark. Mineral oil will
not catch fire without significant heating first, so a spark here is no danger. If you are cutting sodium covered with xylenes, toluene, naphtha, etc,
a small spark will create a large fire. Further, vapors of volatile solvents can travel to other ignition sources, again creating large fires
involving reactive metals.
[Edited on 23-1-2015 by Praxichys]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
