Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Ground glass compatibility
enkephalin
Harmless
*




Posts: 7
Registered: 22-12-2005
Member Is Offline

Mood: No Mood

[*] posted on 24-12-2005 at 05:11
Ground glass compatibility


Could 24/29 (european) joints be used with 24/40 (american) joints? the only difference is the length of the joint i think, the width and angles are the same.... thanks.
View user's profile View All Posts By User
chochu3
Hazard to Others
***




Posts: 185
Registered: 21-10-2003
Location: South Side Tejas [Cloverland]
Member Is Offline

Mood: Inside looking out

[*] posted on 24-12-2005 at 11:13


It is possible, use a keck clamp to make sure it does not blow out of the hole when heating. I use a 19/24 stopper in my 19/22 3 neck flask and have had no problem when heating as long a keck clamp is in place.



\"Abiding in the midst of ignorance, thinking themselves wise and learned, fools go aimlessly hither and thither, like blind led by the blind.\" - Katha Upanishad
View user's profile View All Posts By User
enkephalin
Harmless
*




Posts: 7
Registered: 22-12-2005
Member Is Offline

Mood: No Mood

[*] posted on 25-12-2005 at 04:02


Thanks for the help.
View user's profile View All Posts By User
Mush
National Hazard
****




Posts: 633
Registered: 27-12-2008
Member Is Offline

Mood: No Mood

[*] posted on 11-4-2015 at 06:34


Is 14/20 joint compatible with 14/23?
View user's profile View All Posts By User
gdflp
Super Moderator
*******




Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline

Mood: Staring at code

[*] posted on 11-4-2015 at 07:38


Yes, as long as the first number is the same, the joints are typically compatible.
View user's profile View All Posts By User
macckone
Dispenser of practical lab wisdom
*****




Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline

Mood: Electrical

[*] posted on 11-4-2015 at 08:05


This topic comes up frequently.
Shorter male joints fit nicely in longer female joints.
However longer male joints will only fit in shorter female
joints if there are no interfering parts beyond the joint.
Often the glass beyond the joint is narrower and you
get interference, especially on lower quality glassware.
View user's profile View All Posts By User
gdflp
Super Moderator
*******




Posts: 1320
Registered: 14-2-2014
Location: NY, USA
Member Is Offline

Mood: Staring at code

[*] posted on 11-4-2015 at 08:20


Quote: Originally posted by macckone  
This topic comes up frequently.
Shorter male joints fit nicely in longer female joints.
However longer male joints will only fit in shorter female
joints if there are no interfering parts beyond the joint.
Often the glass beyond the joint is narrower and you
get interference, especially on lower quality glassware.


I could see how that would be an issue with more complex pieces of glassware, but for most simple glassware; flasks and straight condensers and such, I have never had an issue with this. It also depends on how different the lengths of the joints are. In most cases, I doubt that 3mm is going to cause any trouble.
View user's profile View All Posts By User
Mush
National Hazard
****




Posts: 633
Registered: 27-12-2008
Member Is Offline

Mood: No Mood

[*] posted on 11-4-2015 at 09:23


Thanx guys!
Would it be okay even for vacuum distillation?
View user's profile View All Posts By User
Loptr
International Hazard
*****




Posts: 1348
Registered: 20-5-2014
Location: USA
Member Is Offline

Mood: Grateful

[*] posted on 11-4-2015 at 09:55


What size TS glass stoppers are used with each? I thought TS27 went with 24/40, but I have some that are definitely larger. They are Pyrex brand, so do they differ amongst manufacturers?
View user's profile View All Posts By User

  Go To Top