jgourlay
Hazard to Others
Posts: 249
Registered: 9-7-2008
Member Is Offline
Mood: No Mood
|
|
Help: Thermometer bizarrity
Sorry if this is a double post, but I think my prior attempted errored out.
I have a red ink/dye thermometer where the ink has seperated in the glass. THere is ink in the bulb, a 1 or 2" or so gap, and a line of ink for a few
degrees, another gap, and then ink all the way to the small air reservoir in the top.
I've heated it, frozen it. Neither gets all the ink into a contiguous line. Can I fix this? How? Note that I'm assuming that there is no way to
get a reading with it this way.
|
|
|
DJF90
International Hazard
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
You cannot use the thermometer in its current state. There are several ways to fix this, but depends on what you have available.
The first is to cool it in a cryogenic mixture to get all the liquid into the bulb. This has worked for me before using dry ice-acetone.
The second is to heat the thermometer to get everything together. I've seen one "pop" when trying this, so be careful and probably use a heating bath
set at a temperature that should just get the liquid level to rise to the top. I'd advise against using a heat gun unless you're very careful.
Some people have reported success by swinging the thermometer in an arc so that the liquid is forced towards the bulb by centripetal action. Be
careful not to let go of it and be cautious of your surroundings.
|
|
|
DrAldehyde
Hazard to Self
Posts: 82
Registered: 12-1-2014
Member Is Offline
Mood: No Mood
|
|
The swinging method has worked for me. It takes a fair amount of pretty serious whipping motion to get it to work. Of course getting the proper motion
going where you are swinging fast enough to cause fluid to move, without starting/stopping so fast that you break the glass is the real trick. Also,
make sure you have plenty of clearance. I don't recommend heating, too easy too blow out the end.
|
|
|
jgourlay
Hazard to Others
Posts: 249
Registered: 9-7-2008
Member Is Offline
Mood: No Mood
|
|
Thanks all.
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
When you swing the thermometer, it might be wise to tie it to a small cord (or use gaffers "Duct" tape as this hold more securely).
I've never used the cryogenic liquid method, but I have successfully removed gaps in the liquid column be heating (With a blowtorch  ). Not to worry, I was fully protected.
The cryogenic liquid approach sounds the most reasonable to me, if you have access to dry ice.
Fear is what you get when caution wasn't enough.
|
|
|
jgourlay
Hazard to Others
Posts: 249
Registered: 9-7-2008
Member Is Offline
Mood: No Mood
|
|
Thanks guys, worked well.
|
|
|
zig
Harmless
Posts: 42
Registered: 27-1-2014
Location: I whip my hair
Member Is Offline
Mood: Back and forth
|
|
My thermometer pulled the same stunt today. DrAldehyde isn't exaggerating- it takes some seriously violent whipping to clear things up!
What causes this to occur? My thermometer is Hg, so it doesn't seem liquid-type-dependent.
"The chemists are a strange class of mortals, impelled by an almost insane impulse to seek their pleasures amid smoke and vapor, soot and flame,
poisons and poverty; yet among all these evils I seem to live so sweetly that I may die if I were to change places with the Persian king."
-Johann Joachim Becher
|
|
|
Artemus Gordon
Hazard to Others
Posts: 178
Registered: 1-8-2013
Member Is Offline
Mood: No Mood
|
|
If I were to try the whipping trick, I'd make a holder for the thermometer from half-inch PVC pipe and a couple of corks held in with duct tape. Or,
if you want to get fancy, you can buy PVC end caps to fit the pipe and use plumber's PVC cement to glue on the bottom cap. This way you remove the
risk of snapping the thermometer while whipping it, and you have a decent holder to store it in after you fix it.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
