NeonPulse
Hazard to Others
Posts: 417
Registered: 29-6-2013
Location: The other end of the internet.
Member Is Offline
Mood: Isolated from Reality! For Real this time....
|
|
recover ethylene diamine from its dihydrochloride salt
HI, i was wondering if anyone could help me with the procedure to convert ethylene diamine back to a liquid state from its dihydrochloride salt? i
have looked around a bit on this site and other places but i cant seem to find a definate process to do this. there is plenty of info on how to make
ethylene diamine dihydrochloride from the liquid using HCI. i have only found a few small references on using NaOH as a possible way to do this but
not many.there was also a mention of converting aniline back to liquid from its hydrochloride form. could this method be used with ethylene diamine
also? any help on the procedure or a point in the right direction as to where i would find how out would be greatly appreciated. thanks. NP
|
|
|
sonogashira
National Hazard
Posts: 555
Registered: 10-9-2006
Member Is Offline
Mood: No Mood
|
|
You shouldn't be messing with chemicals if you need to ask that.
|
|
|
NeonPulse
Hazard to Others
Posts: 417
Registered: 29-6-2013
Location: The other end of the internet.
Member Is Offline
Mood: Isolated from Reality! For Real this time....
|
|
I know. Electronics is
more my specialty. I'm still learning when it comes to chemistry.
|
|
|
bfesser
|
Thread Moved
24-10-2013 at 06:40 |
Random
International Hazard
Posts: 1120
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
Electronics as in making a spark to detonate something?
|
|
|
woelen
Super Administrator
Posts: 8014
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Why this answer? I unfortunately notice a
change of atmosphere on sciencemadness the last few months. The place seems to become less friendly. This is just one example of such a type of
response, I do not want to put you, sonogashira, in the spotlight, I use your response as just an example of this type of responses.
This may sound like a beginner's question, but the extraction of the free amine can be less straightforward than one thinks of at first glance. The
reaction itself is straightforward, just add enough NaOH and then a slight excess amount to have all of the ethylenediamine released from the ion. But
the isolation of this compound from the water is not that trivial. The amine has a boiling point, close to the boiling point of water. That is one
complication. Another issue is that if you want all of the amine to be released, then you need to use excess NaOH, but if you distill such solutions
and if you want all of the amine to be expelled from the solution, then you need to distill off nearly all liquid. This is very hard on your
glassware. It might even be that you need copperware instead of glassware. I know of a similar problem with distilling hydrazine from solutions of
N2H4.H2SO4 which are neutralized with NaOH. Because of the excess NaOH needed, you need to distill in copper apparatus if you value your glassware.
Maybe extraction in some organic solvent which does not mix with water is an option, but someone with experience in organics may be of more help in
this.
|
|
|
deltaH
Dangerous source of unreferenced speculation
Posts: 1663
Registered: 30-9-2013
Location: South Africa
Member Is Offline
Mood: Heavily protonated
|
|
Well said woelen, even the simplest of processes can be an art to fine tune and get working well.
NeonPulse, another route could be to pass a solution of your salt through a column filled with a strong base type ion
exchange resin in it's 'free base' form. From the bottom will come a solution of relatively pure ethylene diamine in water until the column
becomes saturated with chloride which happens from the top down. You then regenerate the column by flushing with NaOH solution that yields,
separately, a NaCl solution.
Solvent extraction followed by distillation can then be used to get the ethylenediamine back into a concentrated form from the water ethylenediamine
solution and regenerate your organic solvent.
[Edited on 24-10-2013 by deltaH]
|
|
|
NeonPulse
Hazard to Others
Posts: 417
Registered: 29-6-2013
Location: The other end of the internet.
Member Is Offline
Mood: Isolated from Reality! For Real this time....
|
|
Thanks woelen and deltah, these were the kind of answers I was looking for.I knew it was not going to be as simple as it sounds and there was bound to
be thee problem of the amine and waters similar BP.
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
@Woelen; Couldn't the corrosive effect of NaOH on glass be avoided by using a little less NaOH? You would have a little lower yield ethylendiamine but
it will be less bad for your precious round bottom or Erlenmeyer.
|
|
|
woelen
Super Administrator
Posts: 8014
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
It might be that if you use an amount of NaOH just insufficient to convert all ethylenediamineH(+) ions to free ethylenediamine that the effect on the
glass is much less severe. On the other hand, I expect that you need to heat more strongly to het the last free amount of ethylenediamine from the
slurry of solid/liquid mix at the end of the distillation. This will cause a lot of bumping and splattering at the end of the distillation. But it
might be worth a shot.
|
|
|
deltaH
Dangerous source of unreferenced speculation
Posts: 1663
Registered: 30-9-2013
Location: South Africa
Member Is Offline
Mood: Heavily protonated
|
|
This is very interesting... I also found this patent:
"Method for recovering ethylenediamine from an aqueous ethylenediamine solution"
http://www.google.com/patents/US3055809
That describes how to do extractive distillation to break the ethylenediamine/water azeotrope. Looks like all you need is a glycol or
monoethanolamine(MEA)... I'd certainly prefer to work with the glycol myself!
The route I propose now is (i)ion exchange to make ethylenediamine free base in water then (ii) extractive distillation using added propylene glycol
to break the water/ethylenediamine azeotrope.
While the patent is for a continuous extractive distillation column, there is certainly nothing stopping you from carrying this out batch wise.
[Edited on 25-10-2013 by deltaH]
|
|
|
DraconicAcid
International Hazard
Posts: 4334
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
You could also use carbonate to deprotonate the ethylaminediamine (pKa of HCO3- is 10.3, pKa of
H2NCH2CH2NH3+ is 9.9). It might even be possible to do this reaction in dry methanol, and let excess
sodium carbonate absorb any water...
Why do you want to isolate the ethylenediamine? If you want to use it as a ligand, you can usually make it and use it in situ...
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
