Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: Reduction of organic acid to aldehyde.
White Yeti
National Hazard
****




Posts: 816
Registered: 20-7-2011
Location: Asperger's spectrum
Member Is Offline

Mood: delocalized

[*] posted on 18-11-2012 at 12:15
Reduction of organic acid to aldehyde.


This may be a rather fussy question, but is there a practical reaction which allows for the reduction of an acid group to an aldehyde? I've done some searching and came up with nothing but reductions of acid groups all the way down to alcohols.



"Ja, Kalzium, das ist alles!" -Otto Loewi
View user's profile View All Posts By User
tatapouette
Harmless
*




Posts: 6
Registered: 17-11-2012
Member Is Offline

Mood: No Mood

[*] posted on 18-11-2012 at 12:28


There are some methods that describe the reduction of the acid to the aldehyde.
But, often, it seems to work better on the whiteboard than in the flask...

The usual method is indirect and consists in :
- converting caboxylic acid to the methyl ester ;
- reducing to the primary alcohol ;
- smoothly oxidize to the aldehyde.

This usually is found better, even if in three steps, because :
- the first two steps are usually easy, clean and good yielding ;
- there are lots of methods (and papers) for the the third step.

EDIT : oops, my bad... There are some methods for reducing carboxylic acid derivatives more or less easily obtained (acyl chloride etc) to the aldehyde. Starting strictly from the carboxylic acid might be more exotic. I guess the lability of the proton is the main problem here.

[Edited on 18-11-2012 by tatapouette]

[Edited on 18-11-2012 by tatapouette]

[Edited on 18-11-2012 by tatapouette]
View user's profile View All Posts By User
kristofvagyok
National Hazard
****




Posts: 659
Registered: 6-4-2012
Location: Europe
Member Is Offline

Mood: No Mood

[*] posted on 18-11-2012 at 12:47


There bis a LOT reference on this kind of reductions, use the search engine.

I would suggest 2 method:

1: DIBALH. A bit expensive, but great to work with.

2: convert the RCOOH to RCOCl and reduce it with Pd/BaSO4. This is a selective method used widely, it is called Rosemund Reduction.




I have a blog where I post my pictures from my work: http://labphoto.tumblr.com/
-Pictures from chemistry, check it out(:

"You can’t become a chemist and expect to live forever."
View user's profile Visit user's homepage View All Posts By User
Sydenhams chorea
Harmless
*




Posts: 29
Registered: 16-8-2009
Member Is Offline

Mood: No Mood

[*] posted on 18-11-2012 at 12:58


Na(Hg) works too



Il n'y a point de sots si incommodes que ceux qui ont de l'esprit.
François de La Rochefoucauld.
View user's profile View All Posts By User
SM2
Hazard to Others
***




Posts: 359
Registered: 8-5-2012
Location: the Irish Springs
Member Is Offline

Mood: Affect

[*] posted on 18-11-2012 at 13:21


Yeti, were you looking for an electronic explanation as to why it is possible to oxidize an alcohol to the aldehyde/ketone stage? You can easily over do it and take things a step further to the COOH acid. Then again, some alcohols are tougher, and some are very vulnerable. Lots of factors can be involved in such a seemingly simple reaction because your end product is highly reactive, and is best taken up and away as it is formed.
View user's profile View All Posts By User
Dr.Bob
International Hazard
*****




Posts: 2734
Registered: 26-1-2011
Location: USA - NC
Member Is Offline

Mood: No Mood

[*] posted on 19-11-2012 at 06:33


I've tried to do the selective partial reduction of acids to aldehydes. Even the best working reaction usually gives multiple products, which is why I agree with tatapouette. I just try to avoid needing the aldehyde if possible. For example, rather than do a reductive amination of an aldehyde and amine, I would make the amide and then reduce, which works pretty well, in most cases. Not all routes work this way, but aldehydes are some of the most challenging compounds to work with, as they are hard to make, often hard to purify, and most do not store well, as they oxidize, dimerize, trimerize, polymerize, and degrade faster than most other chemicals.
View user's profile View All Posts By User
Nicodem
Super Moderator
Thread Moved
19-11-2012 at 07:29
PHILOU Zrealone
International Hazard
*****




Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline

Mood: Bis-diazo-dinitro-hydroquinonic

[*] posted on 20-11-2012 at 14:39


It doesn't work for all organic acids because of the roughness/harshness of the reaction conditions,
but the fusion (dry distillation) of Calcium formate in excess with the Calcium carboxylate of the organic acid will give you the aldehyde...It works also with Baryum or Strontium.

It is based on the same kind of reaction as:
Ca(O2C-CH3)2 -heat-> CaCO3 + CH3-CO-CH3
Ca(O2C-CH3)2 + Ca(O2C-CH2-CH3)2 -heat-> CaCO3 + CH3-CO-CH3 + CH3-CO-CH2-CH3 + CH3-CH2-CO-CH2-CH3
Ca(O2C-CH3)2 + Ca(O2CH)2 -heat-> CaCO3 + CH3-CO-CH3 + CH3-CH=O + CH2=O

Playing with the proportions allows one to favourise one of the reaction products.
Distillation must be used to separate the products.

In some cases of diacids one can get cyclocetons.
Hexan-1,6-dioic acid leads to cyclopentanone and heptan-1,7-dioic acid to cyclohexanone.
Succunic acid provides 1,4-cyclohexadione.




PH Z (PHILOU Zrealone)

"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
View user's profile View All Posts By User

  Go To Top