zoombafu
Hazard to Others
Posts: 255
Registered: 21-11-2011
Location: U.S.
Member Is Offline
Mood: sciencey
|
|
Help With Magnetic Stirring Bars
Hi, I have recently upgraded myself from a flat-bottom-flask-with- rubber-stoppers-and-all-sorts-of-connecting-tubes distillation setup, and now I
have a RBF ground glass joint setup. The question that I have is what size magnetic stirring bars do i need for a 2000 mL, 1000mL, 500mL, and 100mL
RBF. Also do you need a stirring bar in a 50mL(or smaller) flask? Any help would be greatly appreciated.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
I have 5 sizes of stir bars:
3"
2"
1"
1/2"
1/2" (lightweight)
I have used all of then at one time or another. My largest flask size is 1000mL. The 1/2" and 1" probably get used the most.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
peach
Bon Vivant
Posts: 1428
Registered: 14-11-2008
Member Is Offline
Mood: No Mood
|
|
Have a look on the Bel-art site here. When you click the bar, the description will give you a flask size recommendation.
There are stir bars for 50ml flasks yes. There even tinier bars for 5ml flasks. And tinier again for stirring vials. A topic of interest recently has
been stirring sub 1ml solutions.
Stirring bigger flasks, like 1 and 2l can be difficult nay even a little dangerous, as the bars are prone to decoupling from the magnet underneath and
go whizzing round the flask. They're heavy enough, and can be moving quickly enough, to potentially pop the walls of the flask.
Whether or not it needs stirring is another matter. Quite a lot of the reactions I do in tiny flasks, I will stir. Particularly those under vacuum.
With the big 2l flask, I tend not to even use it. If I am using it, it's probably to distill a lot of solvent and doesn't need stirring anyway.
If you can run something in a beaker (it doesn't need condensing or an inert atmosphere) that is by far the best way to stir things; with a big fat
ass flat stir bar. Some of the things I've done in a beaker would be impossible to stir in an RBF with a magnetic bar. They are good for big
neutralisations, especially if you have things going from solids to solutions, where they will need a lot of stirring and time to completely react and
homogenise.
There are neodymium stir bars for reactions up to 150C. The neodymium magnets are much stronger and less prone to decoupling, but they loose their
magnetism at higher temperatures.
Various stirring thingies.
<a href="http://img687.imageshack.us/i/img2120ja.jpg/" target="_blank"><img src="http://img687.imageshack.us/img687/4116/img2120ja.jpg"
alt="Free Image Hosting at www.ImageShack.us" border="0"/></a><br>
The one in that 50ml flask is about 6-8mm (quart inch odd), but the flask is full of benzene and other filthy shit which I don't want on my hands at
9am, so it's not on display at present.
<a href="http://img11.imageshack.us/i/img2114nm.jpg/" target="_blank"><img src="http://img11.imageshack.us/img11/486/img2114nm.jpg" alt="Free
Image Hosting at www.ImageShack.us" border="0"/></a><br>
A 10ml RBF
<a href="http://img20.imageshack.us/i/img2116y.jpg/" target="_blank"><img src="http://img20.imageshack.us/img20/8591/img2116y.jpg" alt="Free
Image Hosting at www.ImageShack.us" border="0"/></a><br>
The strangely shaped flea bars will stir things like this 50ml pear shaped distillation glass. These bars can also be cut into different shapes for
weird tasks. Despite owning much more expensive glass, this piece was remarkably cheap and I end up using it on a regular basis. Unlike the vacuum
jacketed glass, I can warm the sides of this up with a blowtorch if something tries solidifying on the way out.
<a href="http://img580.imageshack.us/i/img2118y.jpg/" target="_blank"><img src="http://img580.imageshack.us/img580/1266/img2118y.jpg"
alt="Free Image Hosting at www.ImageShack.us" border="0"/></a><br>
[Edited on 31-12-2011 by peach]
|
|
|
Arthur Dent
National Hazard
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
Ha hah, Peach, we seem to shop at the same place!
Anyway, in the image above, you see between the condenser and the vacuum spout one of these tiny "grain of rice" teflon magnets (I bought a bunch of
these) and they are quite useful in a pear-shaped bulb such as this since they tend not to rattle at all when they reach a specific speed. I also use
them extensively in test tubes. They come in lengths from 4mm to 1.5cm.
I've used this mini distilling kit only once and I had set-up a cylindrical sandbath on my hotplate using a flat-bottomed soup can that fit the bulb
quite well. But this is one of those kits that I use quite seldom.
My biggest bar is 5 cm long. I use it with my 1 liter erlenmeyer. It stirs up quite a storm in a jiffy. I wish I had a few of these football-shaped
bars though, heven't seen any at my glassware shop.
Robert
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
|
zoombafu
Hazard to Others
Posts: 255
Registered: 21-11-2011
Location: U.S.
Member Is Offline
Mood: sciencey
|
|
Thank you very much peach and arthur!
Ive been looking for a site that has those flask recommendations, so thank you for that bel-art link.
I remember that once I was mixing a nutrient broth solution solution in a beaker, and the magnet decoupled, bounced once or twice and the beaker
busted. The broth got all over my hot plate and started burning, the smell was horrible  .
|
|
|
Dr.Bob
International Hazard
Posts: 2734
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I have a bunch of oval shaped stir bars available still. I only had a few a while back, but have found an entire bag of them. Most are used, some
look new. Most sell for $10 or more on Bel-Art or VWR, I sell most around $3, and if you want an assortment of oval ones, I can provide a assorted
mix of 5 sizes for ~$10. The only size I have very few left of is the 3/4" x 3/8" oval (which work well in 14/20 glassware). I have lots of the
micro sized ones which are about 3/8 x 1/8", and many of the larger sized ones.
I will caution people that you need to consider the size of the joint, if you have a 14/20 joint, you can only fit in the smaller ones, if you have
24/40 joints, you still cannot fit an unmodified 3/4 dia. oval in it. (We often trim them with a razor to fit in side a 24/40 joint flask if we want
good stirring in a big flask.)
Bob
|
|
|
Panache
International Hazard
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
Peach are you an aristocrat (with an endowed income) with a castle or stately home within which you sit and muse by windowside, hounds attentively
splayed at your feet.
I think you are and its great, please don't dispel this myth if its not true as i find its possibility enjoyable, although i do hate anything other
than strickly egalitarian virtues.
I am Australian after all, the home of egalitarianism and its dark underbelly the tall poppy syndrome.
That is to say keep posting as such, good show.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Good one Panache...I've wondered about this myself.
But more likely Persian cats winding around his feet.
Please explain this syndrome.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
starman
Hazard to Others
Posts: 318
Registered: 5-7-2008
Location: Western Australia
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Panache  | Peach are you an aristocrat (with an endowed income) with a castle or stately home within which you sit and muse by windowside, hounds attentively
splayed at your feet.
I think you are and its great, please don't dispel this myth if its not true as i find its possibility enjoyable, although i do hate anything other
than strickly egalitarian virtues.
I am Australian after all, the home of egalitarianism and its dark underbelly the tall poppy syndrome.
That is to say keep posting as such, good show. |
Got to agree with Panache about Peach.He has an incredible array of equipment (drool) for a young guy.
Chemistry- The journey from the end of physics to the beginning of life.(starman)
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
The tallest poppy get snipped first.
http://en.wikipedia.org/wiki/Tall_poppy_syndrome
[Edited on 7-1-2012 by Bot0nist]
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
Arthur Dent
National Hazard
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
From what has been described above, here's how I imagine our friend Peach:
Robert
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
|
zoombafu
Hazard to Others
Posts: 255
Registered: 21-11-2011
Location: U.S.
Member Is Offline
Mood: sciencey
|
|
It is possible that this is his lab...
Peach's Lab
|
|
|
Hexavalent
International Hazard
Posts: 1564
Registered: 29-12-2011
Location: Wales, UK
Member Is Offline
Mood: Pericyclic
|
|
Back onto the topic of stir bars, I've heard of people making their own by dipping ordinary magnets into wax. What are your thoughts?
"Success is going from failure to failure without loss of enthusiasm." Winston Churchill
|
|
|
zoombafu
Hazard to Others
Posts: 255
Registered: 21-11-2011
Location: U.S.
Member Is Offline
Mood: sciencey
|
|
| Quote: Originally posted by Hexavalent | | Back onto the topic of stir bars, I've heard of people making their own by dipping ordinary magnets into wax. What are your thoughts?
|
While that does sound like a possibly good idea, they probably wouldn't be able to be used at high speeds and stirring hot solutions.
|
|
|
peach
Bon Vivant
Posts: 1428
Registered: 14-11-2008
Member Is Offline
Mood: No Mood
|
|
Ha ha!
I was just thinking of Monty Burns laying in his clean room, {muffled}"Release the hounds!"{muffled}.
Magpie is right though, I have kitties, which sit 20ft up on the roof in the rain meowing at me through the windows because they can see me doing
something below.
I have seen that guys lab, I think he lives in Ireland. I'm not sure. But it's amazing if that's his house. No lab is complete without a pipe organ to
play evil overlord music on whilst waiting for something to finish.
Dipping magnets in wax I doubt is such a great idea. The chances of the wax being dissolved, attacked, contaminating the reaction, taking part in the
reaction or making the results a serious mess to clean up are high enough for it to be a downer.
Because they are spinning, the wax will gradually wear away or could be knocked off in places as it collides with things in the flask and rubs against
the bottom. Warm it up at all, or run a reaction that gets warm on it's own, and the wax will be off. It'll also be more prone to shattering if you
cool it down.
Any defect in the wax will allow the reactants contact with the magnet. Given how harsh some reaction conditions can be, the magnet it's self will
certainly react with a lot of them.
Compare the cost of your reactants, solvents and substrates, and your own wasted time and effort, with spending a few dollars on a PTFE bar, which you
can continually pound with just about anything you like and it won't do anything.
Stir bars used to be glass encapsulated before isostatic PTFE molding came along. That's a better option and something you can easily achieve at home
with a blow torch. But it still has issues when compared with PTFE; glass cracks rather easily, and you will likely have a pocket of air inside it,
which will try expanding as things warm up.
Another option is to buy a length of PFA or FEP tubing from eBay. Those are both sister polymers of PTFE but, quite unlike PTFE, they can be
manipulated more akin to normal plastics, by hot forming (they can be injection molded). You could drop a magnet into a length of that and then hot
crimp the ends shut. By the time you've bought some, paid the postage and done it, you'd still be better off getting an actual stir bar.
Platinum is often used for engagement and wedding rings. PTFE is as incredible in terms of it's resistance. It is even more incredible that it is so
cheap and widespread. Do not ever attempt to use that reasoning to explain a teflon wedding ring.
[Edited on 9-1-2012 by peach]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
