helzblack
Harmless
Posts: 35
Registered: 6-8-2019
Member Is Offline
|
|
Creating eutectics
So I have never made an eutectic salt. I want to make the salt-potassium chloride eutectic.
Do I have to mix them forcefully with a mortar? Dissolve them and then evaporate the water?
How is the eutectic made, it is supposed to melt at around 600C
|
|
|
Rainwater
National Hazard
Posts: 924
Registered: 22-12-2021
Member Is Offline
Mood: Loving every second
|
|
What other compound are you mixing with the KCl?
To the best of my knowledge, KCl will decrease the melting point of water and a few other organic solvents
It will decrease the melting point of calcium chloride when mixed to a ratio of 70% KCl
(going off memory here, lots of crc errors)
https://www.sciencedirect.com/science/article/abs/pii/S09270...
[Edited on 12-10-2024 by Rainwater]
"You can't do that" - challenge accepted
|
|
|
Fulmen
International Hazard
Posts: 1719
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
You need to melt them together. Once one of the components melts the others will start dissolving into it. Finely ground and mixed materials will
probably melt faster, but not at a lower temperature.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
helzblack
Harmless
Posts: 35
Registered: 6-8-2019
Member Is Offline
|
|
@Rainwater Salt and Potassium Chloride
NaCL and KCL
|
|
|
chornedsnorkack
National Hazard
Posts: 563
Registered: 16-2-2012
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Fulmen  | | You need to melt them together. Once one of the components melts the others will start dissolving into it. Finely ground and mixed materials will
probably melt faster, but not at a lower temperature. |
Is it so? Compare water and salts. The eutectic is -21 for NaCl, lower for some other salts. If solid NaCl and solid water are brought to contact at
say -10 degrees, will solid-solid contact initiate melt formation, or will there be no reaction till they are warmed to 0 degrees?
|
|
|
Fulmen
International Hazard
Posts: 1719
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Fair point. As you come close to the melting points there is bound to be some interaction. So in theory you should be able to form the eutectic
slightly below the melting point. But it's going to be a slow process compared to melting the ingredients together.
[Edited on 12-10-24 by Fulmen]
We're not banging rocks together here. We know how to put a man back together.
|
|
|
Deathunter88
National Hazard
Posts: 519
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by chornedsnorkack | | Quote: Originally posted by Fulmen | | You need to melt them together. Once one of the components melts the others will start dissolving into it. Finely ground and mixed materials will
probably melt faster, but not at a lower temperature. |
Is it so? Compare water and salts. The eutectic is -21 for NaCl, lower for some other salts. If solid NaCl and solid water are brought to contact at
say -10 degrees, will solid-solid contact initiate melt formation, or will there be no reaction till they are warmed to 0 degrees?
|
Yes the solid water would melt - this is precisely how road salt works to melt snow and ice.
|
|
|
Bedlasky
International Hazard
Posts: 1240
Registered: 15-4-2019
Location: Period 5, group 6
Member Is Offline
Mood: Volatile
|
|
Awesome eutectic is LiCl-KCl. 41,8 mol % KCl, 58,2 mol % LiCl (anhydrous). Mixture melt at 352 °C, which is very low for ionic chloride mixture.
|
|
|
DraconicAcid
International Hazard
Posts: 4339
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
| Quote: Originally posted by Bedlasky | | Awesome eutectic is LiCl-KCl. 41,8 mol % KCl, 58,2 mol % LiCl (anhydrous). Mixture melt at 352 °C, which is very low for ionic chloride mixture.
|
Molten lithium salts will weaken glass. You get slow ion exchange which makes the glass very brittle.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
knowledgevschaos
Harmless
Posts: 41
Registered: 9-8-2023
Location: Sci-Hub and the hardware store
Member Is Offline
Mood: Hungry for information
|
|
Phase diagrams are super useful for this kind of thing.
This website has a great article on how they work. Although it's specialized for the alloys of metals, everything should still apply for eutectic
salts.
Know thy incompatibilities
|
|
|
Fulmen
International Hazard
Posts: 1719
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
The KCl/NaCl eutectic is pretty underwhelming (650/800C). Adding MgCl2 can drop it under 500C, I'm going to try that as a flux for molten aluminum in
a future project.
If you're just after cool eutectics I would study the K/Na/CaNO3-system. The constituent salts melt from 300-550C, the eutectics go down to 160C.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
Rainwater
National Hazard
Posts: 924
Registered: 22-12-2021
Member Is Offline
Mood: Loving every second
|
|
I accidentally mixed sodium and potassium metal. It was not nice.
It is very unpleasant to depose.
1 drop of water into the alloy was too explosive, so i thought to drip the mix into an extreme excess of water. It worked great until it didn't
Eat through a ptfe stopcock in a seperation funnel and leaked out very, very fast, instantly ignited my table, bucket, grass. Big booms and puffs,
flashes, and pops.
1 of 5 stars will not repeat.
Leftovers turned yellow, poked with a stick from far away. Instant pops.
Wear ear protection
3 of 5 stars would recommend to a friend.
"You can't do that" - challenge accepted
|
|
|
Sir_Gawain
Hazard to Others
Posts: 435
Registered: 12-10-2022
Location: [REDACTED]
Member Is Online
Mood: Stable
|
|
I think he’s referring to a mixture of all three nitrates. Not elemental Na/K.
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
|
Morgan
International Hazard
Posts: 1694
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
When doing some experiments/toying with solid rock salt, I thought it would be nice to make my own solid rock salt, but the melting point is
annoyingly high. I was able to melt or glaze the surface of some table salt with a simple torch but beyond that of course it's more effort to melt it
so the idea of a eutectic appealed to me. It would be nice if a eutectic could retain or improve the high thermal expansion property of rock salt.
When the physicist John Tyndall was studying the Trevelyan Rocker, on this topic, of all the minerals he experimented with, he found rock salt to be
the best. "I scarcely know a substance, metallic or non-metallic, with which vibrations can be obtained with greater ease and certainty than with this
mineral."
A few random experiments tried with salt.
https://www.youtube.com/watch?v=jlD1EGEieC0
https://www.youtube.com/watch?v=5bu01y_6LJU
https://www.youtube.com/watch?v=Yet6p4ja7qQ
https://www.engineeringtoolbox.com/linear-expansion-coeffici...
One curious tidbit if anyone knows, is it possible that this very tiny spark from this tiny hot brass fitting was caused by an electrostatic discharge
when set upon the salt? It occurs at the the 10 second mark and it's very faint. I haven't been able to reproduce it, hoping to amplify it if
possible.
https://www.youtube.com/watch?v=i-7kbkVx8bI
|
|
|
Fulmen
International Hazard
Posts: 1719
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
You are correct, my apologies for the confusion. It is of course KNO3/NaNO3/Ca(NO3)2. NaK is pretty cool, but not really suited for
amateurs. And combining it with nitrates sounds like a bad day in the lab for everyone.
[Edited on 14-10-24 by Fulmen]
We're not banging rocks together here. We know how to put a man back together.
|
|
|
helzblack
Harmless
Posts: 35
Registered: 6-8-2019
Member Is Offline
|
|
| Quote: Originally posted by Fulmen | The KCl/NaCl eutectic is pretty underwhelming (650/800C). Adding MgCl2 can drop it under 500C, I'm going to try that as a flux for molten aluminum in
a future project.
If you're just after cool eutectics I would study the K/Na/CaNO3-system. The constituent salts melt from 300-550C, the eutectics go down to 160C.
|
And how do you plan to mix them to make the eutectic? Mortar and pestle? I have heard that it must be forcefully and intimately mixed, hence why I am
asking if this is correct?
[Edited on 15-10-2024 by helzblack]
|
|
|
chornedsnorkack
National Hazard
Posts: 563
Registered: 16-2-2012
Member Is Offline
Mood: No Mood
|
|
I am unsure that a double eutectic needs forceful mixing. A triple eutectic might.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
