EF2000
Hazard to Others
Posts: 153
Registered: 10-5-2023
Location: The Steppes
Member Is Offline
Mood: Taste testing the Tonka fuel
|
|
How to totally destroy non-stick coating?
Background:
About year ago, I was planning to make some Lithex. Bought both lithium perchlorate and hexamine. And then went to home depot to buy a frying pan. I
remembered what Liptakov said in LL8 thread:
So I chose the most cheap, tiny pan. Maybe it's for small pancakes or some special model for poor undergrads who lost their stipend, don't know. (Local pancakes are thin but huge; small are Western perversion of a whole pancake idea)
Pan surface wasn't clean steel, but I assumed that there can't be PTFE on such cheap one, and that it's some decorative paint.
Guess what? I was proven wrong: the moment I added LiP to heated pan, it started decomposing. So there must be at least some teflon here.
Now I'm trying to remove the coating. Tried dissolving it with household-grade acetone (cause it's most likely not pure teflon), failed. Tried
scraping it of with sandpaper, steel brush and flat screwdriver, it kind of works but scratches metal surface (also eww, hard physical
labor+not-so-healthy dust).
So, the question:
Is there some clever way to remove fluoroplast-based non-stick coating from a pan?
Like some strong solvent to dissolve it back to the stone age?
[Edited on 16-9-2023 by EF2000]
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
2 minutes with Google and you would know you are already using the best (and likely safest) method: abrasive + elbow grease. Unless you have some
perfluorinated elbow grease?
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
EF2000
Hazard to Others
Posts: 153
Registered: 10-5-2023
Location: The Steppes
Member Is Offline
Mood: Taste testing the Tonka fuel
|
|
Quote: Originally posted by Twospoons  | | 2 minutes with Google and you would know you are already using the best (and likely safest) method: abrasive + elbow grease. Unless you have some
perfluorinated elbow grease? |
Alright, thought so. I have been going to continue scraping anyway, just asked here in case someone has better plan, like "mate, just heat it with
magnesium powder and see how quickly it'll burn off" or something like that. (Also DuckDuckGo >> Yes we spy, Inc.)
|
|
|
BromicAcid
International Hazard
Posts: 3245
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Molten sodium hydroxide?
|
|
|
clearly_not_atara
International Hazard
Posts: 2787
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Attachment: TeflonSolubility.pdf (903kB)
This file has been downloaded 210 times
|
|
|
Rainwater
National Hazard
Posts: 919
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
LiP seams to work well.
Without buying anything, high heat (+350c) then dunking in water and elbow grease
For about 10 bucks
https://www.walmart.com/ip/Mainstays-Stainless-Steel-10-Piec...
These work reasonably well for molten sodium, potassium and lithium but being a walmart stainless steel, they are magnetic, which means they are not
stainless steel.
They will eventually corrode from high heat, but so will everything
"You can't do that" - challenge accepted
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
There are ferromagnetic stainless steels - typically 400 series alloys.
But 304 is usually used for cookware, and isn't ferromagnetic.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
EF2000
Hazard to Others
Posts: 153
Registered: 10-5-2023
Location: The Steppes
Member Is Offline
Mood: Taste testing the Tonka fuel
|
|
Breaking news from the frontline: PTFE forces are defeated by some dummy with dish scourer.
Thank you all for reassuring that abrasives are the easiest way! After a bit of scraping and sandpaper-ing, I decided to go into full-scale offensive
and went to the kitchen. About 2 hours or so of scouring with steel dish scourer and washing soda, I removed most of coating. Hardest part was the
sides, main part on the bottom got away really quickly.
Then I sandpapered what remained and polished it a bit with GOI paste (chromium(III) oxide-based abrasive, one of the
finest parts of Soviet legacy, along with Soyuz rockets and smoothbore tank cannons. Served me well for cleaning spot rust from my training
sword).
Then washed paste remains away with ordinary dish washing liquid.
Well, I think it's success: pan shines in the sun, fluoroplast is gone and I didn't choose slippery consumerist way. Thanks again for your suggestions
and support!
(Handle says: "Not for food!")
|
|
|
charley1957
Hazard to Others
Posts: 159
Registered: 18-2-2012
Location: Texas
Member Is Offline
Mood: Roasting
|
|
(Handle says: "Not for food!")
Nice touch
You can’t claim you drank all day if you didn’t start early in the morning.
|
|
|
Texium
|
Thread Moved
17-9-2023 at 07:38 |
Dr.Bob
International Hazard
Posts: 2733
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
If you really want to destroy the non-stick coating, just let my wife use it a couple of times, she can scratch it up good and peel it right off.
:-)
|
|
|
Texium
|
Thread Moved
5-12-2023 at 13:58 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
