coyote
Harmless
Posts: 16
Registered: 5-1-2017
Member Is Offline
Mood: No Mood
|
|
Separating stuck ground glass joint
I have two 24/40 pieces of glassware stuck to eachother, and I have tried pulling them apart, twisting them, and heating up the outer one with my heat
gun, but I've been unable to separate them. I tried getting some kind of liquid in the joint but nothing is permitting it.
Any ideas on how to get these unstuck?
|
|
|
arkoma
Redneck Overlord
Posts: 1761
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
I have had some luck boiling them in a sodium carbonate base bath. Have a stopper stuck in a 100ml RBF at the moment and probably attempt to break it
without screwing up the 24/29 joint on the flask.
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
|
coyote
Harmless
Posts: 16
Registered: 5-1-2017
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by arkoma  | | I have had some luck boiling them in a sodium carbonate base bath. Have a stopper stuck in a 100ml RBF at the moment and probably attempt to break it
without screwing up the 24/29 joint on the flask. |
Good idea, I'll try that and send an update when I get home from my classes.
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Wiggling the joint side to side (as if trying to bend at the joint) works much better than twisting.
A little WD40 helped me to un-freeze a joint.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Clear_horizons_glass
Harmless
Posts: 42
Registered: 30-9-2019
Location: Pullman, WA
Member Is Offline
Mood: Glass
|
|
Running them through an annealing cycle. So ya need to put it in an oven or kiln and slowly heat it up to 1050F and then slowly cool it down.
If you can get the slightest drop of water in between the joints sometimes you can heat it up very slowly and the steam helps.
A Bunsen burner might be better at separating the joints that a heat gun. Start above the flame an inch or two and slowly work your way into the
flame.
Clear Horizons Laboratory Glassblowing Services
-------------------------------------------------------------
www.clearhorizonsglass.com
Phone and Fax:
(855) LAB-GLAS
(855) 522-4527
Have a glass project you want made? email me at
info@clearhorizonsglass.com
or message us here |
with a U2U |
message |
\/
|
|
|
j_sum1
Administrator
Posts: 6320
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
Patience.
I have broken many stuck joints through being impatient. (I don't want to buy any more sep funnels for a while if I can help it.)
My last stuck joint was on a vacuum desiccator. I resisted the temptation to apply any significant force. When it did not come apart with a couple
of taps with a wooden dowel I sprayed it liberally with WD40 and left it in a position where the oil would soak into the joint. Two days later it was
still stuck. On the third day it came free with a finger-touch.
|
|
|
coyote
Harmless
Posts: 16
Registered: 5-1-2017
Member Is Offline
Mood: No Mood
|
|
Update: I made an idiot move, I tried to force it open after getting wd40 in it, it cracked in my hand and cut it open.
Anyways, I'll just smash the rest of the glassware that's already broken to get it off
|
|
|
Rainwater
National Hazard
Posts: 919
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
Sorry for your loss. Rethink, reuse, recycle.
My broken glass gets cleaned, ground joints are cut off and annealed.
Unusable pieces are brough to red heat and tossed in a bucket of water to produce fritz material.
Its great as boiling stones. Tried a few times to make a filter fritz, always ends up cracking.
Manages to fuse a male joint to a test tube to make a long thermowell once. It works perty good
"You can't do that" - challenge accepted
|
|
|
Osmiridium
Harmless
Posts: 26
Registered: 13-3-2023
Location: Multiverse
Member Is Offline
Mood: excited
|
|
Be careful.
Using force might actually work sometimes in this case. If there's an expensive apparatus involved, the cheaper part, like a stopper that's stuck, may
be destroyed purposedly to get it off.
But it's very important to wear cut resistant safety gloves and protective goggles. It should be clear that broken glass is sharper than a razor and
may cause horrible injuries.
It is very important to always grease the joints properly, especially if there are alkaline solutions involved or the tolerances of the ground joints
are high (cheap glassware).
Ethanolic KOH is a good mixture to soak it in that might help. I also cleans the glassware nicely.
|
|
|
pneumatician
Hazard to Others
Posts: 411
Registered: 27-5-2013
Location: Magonia
Member Is Offline
Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **
|
|
The last I read, put pressure with fingers around the joint. The labglass makers are sadistic idiots??? from where get ideas to make the labware??
from his asshole?? :-D
now this people maybe start to wake up??
https://www.aliexpress.com/item/4000554896023.html?spm=a2g0o...
I ended in making my own "design", I searched a guy making labware and my flask are all the news with male joint. The stopper is a 50, 100 ml...
female joint flask. if any problem, I put the "stopper" between two wood tables and with a dry impact the "stopper" is liberated. And now I can
"froze" very hard the "stopper" because I can remove it no matter how hard is joined. I'm very happy, inclusive now for distillation too I buy male
joints, and when all the olds broke never buy it again. With the same price!
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
