Chemgineer
Hazard to Others
Posts: 216
Registered: 25-5-2021
Member Is Offline
|
|
Nitric Acid
If I have a 10% concentration of Nitric Acid, can I boil it to increase the concentration? I note Nitric Acid boils at 83 deg C but a 68%
concentration boils at 121 deg C.
Will boiling my 10% just boil out my Nitric Acid lowering the concentration?
|
|
|
Antigua
Hazard to Others
Posts: 155
Registered: 27-9-2020
Member Is Offline
|
|
Yes - you can concentrate HNO3 up to 68%. At this concentration it's going to form what's called an azeotrope - when boiling it, you'll evaporate the
same ratio of water and acid, thus distilling the same thing you heated up.
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
In practice the above is limited. When you boil nitric acid, then the vapor, leaving the liquid will contain a percentage of HNO3, which is a function
of concentration of the acid. For concentrations, less than the azeotropic concentration, the concentration of HNO3, leaving the boiling liquid, is
lower than the concentration of the acid in the liquid, but it is not zero. The closer you get to the azeotropic concentration, the closer the
concentration of HNO3-vapor comes to the concentration of HNO3 in the liquid.
E.g. with 10% HNO3, near boiling temperature, the vapor will be almost 100% H2O.
With 40% HNO3 in the liquid, near boiling temperature, the vapor will contain around 25% HNO3.
With 50% HNO3 in the liquid, near boiling temperature, the vapor will contain around 40% HNO3.
So, concentrating the acid by boiling is possible, but the losses increase with increasing concentration of HNO3 in the liquid. In practice I think
that you can go to 25% or so without excessive losses. Of course, you can collect the vapors (especially from concentrations above 20% or so) and keep
that liquid as an additional dilute, but high purity, stock of nitric acid.
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
woelen is correct; when I've done this in the past even the first few drops of distillate turn blue in contact with copper. When you distill nitric
acid from a mixture that has a considerable amount of dissolved solid, like the leftover material from a nitric acid preparation that has been
re-dissolved, it's actually possible to pass up the azeotrope; the concentration of nitric acid keeps increasing well into the 80-90% range. So when I
add water to that big solid puck of sodium bisfulfate/nitrate/sulfate etc. and continue my distillation, I usually collect a large, somewhat dilute
fraction, and then a fair bit of very concentrated acid as well.
|
|
|
Chemgineer
Hazard to Others
Posts: 216
Registered: 25-5-2021
Member Is Offline
|
|
Thanks for the detailed explanations, i'm just getting the concept straight in my head of how azeotropes work and which vapour will come off first.
I'm going to open boil my 10% to half the volume first and then probably distil it to give two concentrations... then bottle it.
|
|
|
arkoma
Redneck Overlord
Posts: 1761
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
bee careful. no2 fumes are ugly. invest in a disty kit if u dont have one
edit...my kb got wet
[Edited on 6-17-2021 by arkoma]
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
