Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Freezing point depression by impurities?
How big of an effect does impurities have on freezing point? Can even minor contamination of solvents decrease freezing point significantly?
|
|
unionised
International Hazard
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
It depends on the solvent.
https://en.wikipedia.org/wiki/Cryoscopic_constant
but the effect is usually quite small.
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Strange. I got a compound that should freeze at approx -17, but it remains crystal clear at -30C and no agitation has effect on it. Every test
performed on it indicates that it is what it's supposed to be, but this is out of range.
|
|
metalresearcher
National Hazard
Posts: 737
Registered: 7-9-2010
Member Is Offline
Mood: Reactive
|
|
Quote: Originally posted by Fyndium | Strange. I got a compound that should freeze at approx -17, but it remains crystal clear at -30C and no agitation has effect on it. Every test
performed on it indicates that it is what it's supposed to be, but this is out of range. |
That is called Supercooling. Recently I evacuated a flask with clean (tap-)water of 14 C and it remained liquid until -4 C and then it froze.
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
That's why I noted the agitation, I shaked the bottle, but nothing happened. This always freezes any liquid that's supercooled.
|
|
unionised
International Hazard
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
It's not guaranteed- especially if the liquid is viscous.
The other thing that often works is scratching the inside of the container with a glass rod.
Until you actually have the solid and liquid together, you don't know what the freezing point is.
|
|
CharlieA
National Hazard
Posts: 646
Registered: 11-8-2015
Location: Missouri, USA
Member Is Offline
Mood: No Mood
|
|
The interesting fact here is that the depression of the freezing point can be used to estimate the equivalent mass of the solute...just another
factoid from the ancient era of "wet" chemistry.
|
|
zed
International Hazard
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Yup! I remember using the Melting point depression concept to estimate the molecular Wt. of an unknown.
But, when we talk about "freezing point", we are also talking about crystallization.
Crystallization is tricky. It can take weeks, months, years, for crystals to form.
Are you sure you have the pure stuff, free of solvents and interfering crud?
Maybe refusal to crystallize (or solidify), is telling you something about the purity of your product.
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
It's not 99% pure, it very likely contains at least a little of the lower fraction as I did not use fractionating column when I vacuum distilled it. I
tried to use it in a reaction and it seems to indicate that it is over 90% at least.
I might do a fractional distillation to it just because I want to know how much of what is in it, and I want to get it crystallize at given temp.
On the other hand, in the topic of benzaldehyde, I remember reading two freezing points, one was -56C and other was -26C. I got the impure one
partially crystallize, and the distilled one remained liquid. So I suppose one does not simply freeze all kind of stuff.
|
|