njl
National Hazard
Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline
Mood: ambivalent
|
|
Definitive POCl3 prep
After UTFSE I've seen several claims that P2O5 and NaCl should react at high temperatures to form POCl3. The only ref I've found will be linked below,
but in their experiments they always used a fluoride salt as well as NaCl. Can anyone weigh in on this?
Attachment: Tarbutton.POCl3.from.P2O5.NaCl.pdf (802kB)
This file has been downloaded 274 times
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
See Lerner, Leonid (2011). Small-Scale Synthesis of Laboratory Reagents with Reaction Modeling. Boca Raton, Florida: CRC Press. pp. 169–177. ISBN
9781439813126. PDF available from libgen.
| Quote: |
19.3.1 Preparation from P2O5
The best reaction vessel for this preparation is a test tube with a quickfit joint, a capacity of at least 100 mL, and at least 22 mm in diameter. If
this is not available, a 100-mL, single-neck flask can be used instead with a slight loss of yield. Scaling the reaction requires proportionally
larger vessels.
First, 35.1 g (0.25 mol) of phosphorus pentoxide is rapidly introduced into the reaction vessel, ensuring that as little atmospheric moisture as
possible reacts with the P2O5, as it subsequently generates HCl and HPO3, which attacks the glass. The transfer is best done by inverting a powder
funnel inserted into the reaction vessel, over the mouth of the reagent bottle, and tilting until approximately the right amount of reagent is
transferred into the flask. Next, 34 g (0.58 mol) of finely ground and thoroughly desiccated (1 h at 250°C) NaCl is added, and the reagents
thoroughly mixed. The approximately twofold excess of NaCl improves the yield by about 10%. Finally, about 10 g NaCl is poured in a layer on top of
the mixture, which serves to convert unreacted P2O5 subliming from the reaction zone (bp 360°C). The reaction vessel is placed in an air oven and
connected to a bend leading through a Liebig condenser to a receiver flask immersed in cold water. The outlet from the flask is vented through a CaCl2
protection tube with a bubbler optionally attached for observation of reaction progress.
The oven is rapidly heated to 270°C, from where the temperature is raised more slowly to 450°C at about 65°C/h. A distillation conducted more
rapidly than this will serve both to reduce yield by excessive sublimation of P2O5, and increase the possibility of the reagent vessel bursting due to
excessive buildup of HCl and POCl3 pressure inside the reactor, as these do not have sufficient time to percolate through the viscous sodium
metaphosphate medium (the reagents liquefy during the reaction). About 8.2 g (0.053 mol) POCl3 collects in the receiver at the end of the reaction
while the reactor tube loses 9.3 g (the difference is due to losses in the distillation setup), corresponding to a yield of 76% (86% with respect to
reactor weight loss) based on P2O5.
|
[Edited on 3-7-2020 by DavidJR]
|
|
|
njl
National Hazard
Posts: 609
Registered: 26-11-2019
Location: under the sycamore tree
Member Is Offline
Mood: ambivalent
|
|
Perfect, Thanks.
Edit: In the interest of not starting a new thread, could P2O5 be used to dehydrate a secondary amine salt to an amide (akin to formamide synthesis).
I know that excess dehydration of primary amides can give nitriles, but it seems like a substitution on the nitrogen would prevent this. I can't find
any work on this so I'm not expecting a definite answer, but unless anyone can see any glaring issues with this logic I think I might experiment with
this idea.
[Edited on 3-7-2020 by njl]
|
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
