Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
how to pump nitric acid?
i'm trying to build a new apparatus for the home production of nitric acid, and part of the process is absorbing the gas in water.
i could use the classic boubbler, but i would need multiple stages to reoxidize any NO formed, a youtuber did it, but i won't be able to generate much
pressure to force the gas and an excess of air through multiple wash bottles.
my other option as an absorbtion column, and i want to try this.
i want to trickle the dilute acid from the top of the column while the feed NO2/Air is at the bottom, and pump back at the top the acid in the
receiver at the bottom of the column.
what pump could survive this?
my first thought is a peristaltic pump with a flexible teflon tubing, the issue is i can't find someone that sells to privates, or that sells small
quantities, i don't need $1000 worth of teflon tubing, i just need the 15cm or so for the pump, and use standard teflon tubing for the rest.
the other idea i had is an all aluminium piston pump. aluminium IIRC is not attacked by nitric acid thanks to its oxide layer, but this might be a
hard thing to pull off for cheap.
any ideas/suggestions/tips?
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
ahill
Hazard to Self
Posts: 57
Registered: 8-1-2015
Member Is Offline
Mood: triumphant
|
|
Suck the NO/air thru the bubblers Instead of pushing it.
|
|
|
Sulaiman
International Hazard
Posts: 3696
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Online
|
|
I think that ptfe tubing may be too rigid for a peristaltic pump,
Viton tubing may suit your purposes,
e. g. cnviton.com
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Eddie Current
Hazard to Self
Posts: 78
Registered: 25-7-2018
Member Is Offline
|
|
Tygon tubing isn't cheap, but it will do the job.
https://www.welco.net/dcms_media/other/05.Chemical_Resistanc...
|
|
|
Refinery
Hazard to Others
Posts: 371
Registered: 17-2-2014
Member Is Offline
Mood: Still
|
|
I used simply manual charge and gravity feed for cryogenic coolant. The flowrate was so low that 10 liter reserve had to be recharged only every 3
hours.
|
|
|
mackolol
Hazard to Others
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
As for the aluminium, NO2 dissolved in water will corrode it quite significantly. Not all of the NO2 reacts with water, some of it just dissolves.
And for teflon tubing, I bought it in some brewing shop. It wasn't expensive and does perfect job through all of my chemistry years, but it isn't very
flexible...
[Edited on 19-6-2020 by mackolol]
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
| Quote: |
Suck the NO/air thru the bubblers Instead of pushing it. |
my aspirator pump is really loud, and i care a bit too much about my rotary vane pump, then again, i'm trying to do something different from a multi
stage absorbtion system
| Quote: |
I think that ptfe tubing may be too rigid for a peristaltic pump, Viton tubing may suit your purposes, e. g. cnviton.com |
yeah teflon tubing is rigid, my pla was to use a flexible tubing for the pump, and then rigid teflon tubing to connect the pump to the glassware (this
way i need only a few centimeters of flexible acid resistant tubing, instead of 1.5m)
| Quote: |
I used simply manual charge and gravity feed for cryogenic coolant. The flowrate was so low that 10 liter reserve had to be recharged only every 3
hours. |
eh, i'm not aiming for a small scale nitric acid plant, more like 1L every now and then (NA is still hard to find and expensive here, i could make 1L
for maybe 3 euros with this method though)
| Quote: |
As for the aluminium, NO2 dissolved in water will corrode it quite significantly. Not all of the NO2 reacts with water, some of it just dissolves. And
for teflon tubing, I bought it in some brewing shop. It wasn't expensive and does perfect job through all of my chemistry years, but it isn't very
flexible... |
bye bye aluminium pump idea
ok so now i need to find someone that sells viton or tygon tubings to privates and not in bulk
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Venturi pump if you have access to compressed air but it's not going to be quiet or clean. Industrially this easily handled with PTFE double diaphragm
pumps but that's supremely overkill for 1 liter of fluid.
|
|
|
RedDwarf
Hazard to Others
Posts: 166
Registered: 16-2-2019
Location: UK (North West)
Member Is Offline
Mood: Variable
|
|
No idea if this is the flexibility or diameter that you need for your peristalic pump but might be worth pursuing further: https://www.ebay.co.uk/itm/VITON-RUBBER-TUBE-3-2MMID-X-6-2MM...
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
| Quote: |
Venturi pump if you have access to compressed air but it's not going to be quiet or clean. Industrially this easily handled with PTFE double diaphragm
pumps but that's supremely overkill for 1 liter of fluid. |
sadly no compressed air, but even if i did have it i think this kind of pump would mess up with the flow as it would push more air from the top, while
i want the gas to raise from the bottom of the column.
thanks a lot! i'm looking on ebay many listings, just tryiing to find the best deal.
i also tried searching for tygon, but apparently there are many grades, and some resist acids better than others, i can only find generic tygon for
fuel lines or the specific acid resistant one, but in bulk sizes
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
If your apparatus can hold a bit of positive pressure it might be possible to circulate the liquid without a pump.
Okay, I know this will sound a bit goofy, and probably isn't the smart solution, but picture that the liquid and gas from the absorption tower are
both led into an Erlenmeyer flask through 2 holes in the stopper, and the third hole in the stopper has a vertical glass tube that dips to nearly the
bottom of the flask.
Both the liquid, and the larger volume of gas, will be forced up the tube.
This will probably happen in a slurping, bubbling way that results in drops of liquid being forced up the tube by the gas pressure with considerable
gas between them.
At the top, this tube is bent over so it empties into an addition funnel.
The addition funnel has a vent tube out the top to let the gas out, and the drip tip at the bottom runs the liquid back into the top of the tower.
Yes, the tower is under slightly increased pressure, but this is produced by a column consisting of mostly gas with drops of liquid spaced out in the
rising tube, and it has less weight per unit of height than the solid but shorter column of liquid in the addition funnel forcing its way into the
top of the gas tower.
So this idea is certainly a long-shot and probably not worth the effort when there are acid proof pumps out there, but it would be an interesting
apparatus if it worked.
The liquid bubbling and rising, the gas absorbing, If you ran it out on the porch you'd probably have stoned people showing up to stare at it like an
unusually toxic and corrosive lava lamp.
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
Quote: Originally posted by SWIM  | If your apparatus can hold a bit of positive pressure it might be possible to circulate the liquid without a pump.
Okay, I know this will sound a bit goofy, and probably isn't the smart solution, but picture that the liquid and gas from the absorption tower are
both led into an Erlenmeyer flask through 2 holes in the stopper, and the third hole in the stopper has a vertical glass tube that dips to nearly the
bottom of the flask.
Both the liquid, and the larger volume of gas, will be forced up the tube.
This will probably happen in a slurping, bubbling way that results in drops of liquid being forced up the tube by the gas pressure with considerable
gas between them.
At the top, this tube is bent over so it empties into an addition funnel.
The addition funnel has a vent tube out the top to let the gas out, and the drip tip at the bottom runs the liquid back into the top of the tower.
Yes, the tower is under slightly increased pressure, but this is produced by a column consisting of mostly gas with drops of liquid spaced out in the
rising tube, and it has less weight per unit of height than the solid but shorter column of liquid in the addition funnel forcing its way into the
top of the gas tower.
So this idea is certainly a long-shot and probably not worth the effort when there are acid proof pumps out there, but it would be an interesting
apparatus if it worked.
The liquid bubbling and rising, the gas absorbing, If you ran it out on the porch you'd probably have stoned people showing up to stare at it like an
unusually toxic and corrosive lava lamp.
|
eh as you described it, it wouldn't work, no liquid is going to flow from the funnel as the pressure of the system is higher and the funnel is open to
the air (same thing as when you open the stopcock on an addition funnel and forget to remove the cap, liquid won't flow).
maybe an airlift pump but the head is too high for a small flow of air
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
flaminglasrswrd
Harmless
Posts: 9
Registered: 17-9-2019
Member Is Offline
|
|
Viton comes in a soft variety that is suitable for peristaltic pumps. But there are cheaper Tygon varieties based on PVC that will work for nitric acid.
In either case, you should consider the peristaltic pump tubing as a consumable.
A glass syringe pump would work as well. It would last forever, but be more expensive upfront. There are some DIY versions out there that are fairly
cheap.
May I ask how you are producing your NO? Plasma?
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
| Quote: Originally posted by flaminglasrswrd | Viton comes in a soft variety that is suitable for peristaltic pumps. But there are cheaper Tygon varieties based on PVC that will work for nitric acid.
In either case, you should consider the peristaltic pump tubing as a consumable.
A glass syringe pump would work as well. It would last forever, but be more expensive upfront. There are some DIY versions out there that are fairly
cheap.
|
i thought about a glass syringe, but it also need check valves, and those also must survive the acid.
| Quote: |
May I ask how you are producing your NO? Plasma? |
Nope, thermal decomposition of calcium nitrate fertilizer, it is cheap when bought in bulk, and you don't even need sulphuric acid
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
Heptylene
Hazard to Others
Posts: 319
Registered: 22-10-2016
Member Is Offline
Mood: No Mood
|
|
Shameless plug of my own abosrption column.
I used an "IWAKI" type pump. Actually a chinese copycat, model number is MP-6RZ bought on aliexpress.
The pump head is polypropylene, so chemically resistant. It is not self-priming! It must be full of liquid to start, it doesn't suck air and draw
liquid through the inlet.
[Edited on 22-6-2020 by Heptylene]
|
|
|
flaminglasrswrd
Harmless
Posts: 9
Registered: 17-9-2019
Member Is Offline
|
|
Ahhh. Nice. I might have to look into that.
I bought 5lbs of "calcium nitrate" for hydroponic use a while ago. I didn't realize that it was actually calcium ammonium nitrate. It should still
work, albeit at lower conversion.
Maybe a tesla valve would work well here. The pumping cost is negligible so a little inefficiency might be worth the long life?
You could also just try some cheap aquarium check valves. They might be constructed with nitric resistant plastic, a lot of plastics are. Who knows?
Nicely done! Have you looked at ozone injection?
[Edited on 22-6-2020 by flaminglasrswrd]
|
|
|
densest
Hazard to Others
Posts: 359
Registered: 1-10-2005
Location: in the lehr
Member Is Offline
Mood: slowly warming to strain point
|
|
One way valves made with thin Teflon flaps are feasible. It's flexible enough for that.
I have a diaphragm pump made entirely of Teflon & other fluoroplastics.
In your case the devil is in the details. How concentrated will the acid be and how much dissolved NO2?
Polypropylene will work for a while but degrades.
Other than fluoroplastics you should consider anything organic as a consumable.
For concentrated or hot acid I don't know oof any tubing which would work in a peristaltic pump. THe compression and stretching would force the acid
into any crack rapidly eating through.
Viton, EDPM, and Kalrez are possible. Under 3M and under 70C you have a lot of choices for tubing.
Butyl rubber is mentioned on some charts.
|
|
|
Heptylene
Hazard to Others
Posts: 319
Registered: 22-10-2016
Member Is Offline
Mood: No Mood
|
|
Thank you!
No I never thought about that, but it sounds interesting! I'll try when whenever I've repaired my tube furnace. I had considered running the
absorption tower on dilute hydrogen peroxide though, considering it is much more available than nitric acid. Anyways, I don't want to hijack this
thread...
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
| Quote: | | I bought 5lbs of "calcium nitrate" for hydroponic use a while ago. I didn't realize that it was actually calcium ammonium nitrate. It should still
work, albeit at lower conversion. |
i have the same mixed salt, it works, but ammonium nitrate also decomposes to N2O, and in small quantities into ammonia and nitric acid that combine
again in cooler parts forming a white smoke (i have already done a few small scale experiments). My plan is to add some lime (super cheap) and convert
all the ammonium nitrate to calcium nitrate and ammonia, it is another step that is going to take some days (filtering, evaporating the water and then
drying the salt)
| Quote: |
Maybe a tesla valve would work well here. The pumping cost is negligible so a little inefficiency might be worth the long life?
|
mh tesla valves don't work that well with low speed fluids
[Edited on 22-6-2020 by Ubya]
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
