Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
Hotplates
Ok, so here's the deal.
I am thinking of following the tutorial on the wiki to synthesize salicylic acid from acetylsalicylic acid. Only problem is, I need to heat a solvent
(acetone or isopropanol), however, I do not have a hotplate right now, nor the money to buy one. So my question is, what should I do, I do not need
stirring, all I need is a safe way to heat glassware containing flammable solvents.
Can I just buy a cheep camping hotplate, is there something that makes this impractical, just some things I should know. Or, is there something I can
put my burner (home science tools pressurized alcohol) in?, Something I can do with it?
Any help is appreciated.
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
|
stephill92
Harmless
Posts: 23
Registered: 19-3-2019
Member Is Offline
|
|
I have done this reaction using an out door burner attached to a grill, and everything worked out fine. I would recommend using a camping stove
however if you have one since they are a bit more mobile. If you do choose to use an open flame make sure you have a plan to put out a potential fire
in case something goes wrong.
|
|
|
Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
OK, interesting. What solvent did you use? I read that both acetone and isopropanol vapours are heavier than air, is this true? Is it no problem
because it disperses in air outdoors?
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
|
mackolol
Hazard to Others
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
I strongly recommend just buying cheap electric kitchen hotplates, I would even say, that these are the essential in amateur lab. In my country one
costs about 30zł (7Euro), so it is extremely cheap, but they are very durable and can heat very fast to 500C. It is even stronger than my hotplate
stirrer (400C) So I use it when I need high temps or just don't need stirring.
It is still way better than burners, because it eliminates (or at least reduces) the risk of fire, and is more precise than just open flame. And come
on don't you have 7Euro or whatever currency?
[Edited on 14-5-2020 by mackolol]
|
|
|
Sulaiman
International Hazard
Posts: 3697
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
+1 for the cheap hotplate.
Plenty of power when required
cheap enough to not worry about occasional spills
I also like to use cooking oil in a metal pot on the hotplate for heating flasks
as it is less likely to stress glassware than a bare hotplate.
(hotplate surfaces and glassware bottoms are rarely flat, so hotspots are normal)
but I do prefer my heating mantles for heating RBFs (diy 500ml and a free 5l)
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Chemorg42  | | OK, interesting. What solvent did you use? I read that both acetone and isopropanol vapours are heavier than air, is this true? Is it no problem
because it disperses in air outdoors? |
I used a butane camping stove with methanol as my solvent first time with a reflux condenser. After getting sick and tired of buying fuel I ordered a
heating mantle insert from Deschem, and been happy ever since!
I used an old coffee tin and light dimmer for the control of it, very cheap!
No worry, but I have halon and ABC extinguishers and lots of experience with solvent fires! (I use methanol/Ethanol a lot for starting my wood stove!
(Living it up like 1785!))
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Do not use open flames to heat vessels of flammable solvents. It is an accident waiting to happen/
|
|
|
Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
OK, I will probably pick up a cheep kitchen hotplate. Now another question, can I put my glassware directly on the hotplate, or should I put wire
gauze between them?
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Use a water bath, especially with these water miscible solvents. If something breaks at least it is contained and diluted with water.
No matter whether you are using a flame or a hot plate, always use a bath of some kind. Water with low boiling stuff, oil or sand with higher boiling
stuff. Acetone or IPA on a hot plate will also catch fire.
|
|
|
Syn the Sizer
National Hazard
Posts: 600
Registered: 12-11-2019
Location: Canada
Member Is Offline
|
|
| Quote: Originally posted by Chemorg42 | | OK, I will probably pick up a cheep kitchen hotplate. Now another question, can I put my glassware directly on the hotplate, or should I put wire
gauze between them? |
I have a stirring hotplate, I stick my glass right on the hotplate. That's what we do in school I have only ever used a gauze when heating with flame
and I think that is to spread the heat out more than protect the glass. Though I am sure somebody will come on here with more info.
|
|
|
Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
OK, so the last two replies seem to represent two extremes. Is it really necessary to use a water bath with a cheep hotplate or alcohol burner? Is it
really safe to place glassware directly on a hotplate?
I don't know the answers to these questions, just not sure what to think.
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I would use a water bath, it is just safer. It can be as simple as a pot or a pan. If you use hot water from a cooker to fill it it is even faster
than waiting for the hotplate to heat your reaction.
|
|
|
Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
OK, but how do I keep things like beakers and flasks from floating, or is the water just not that deep.
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
|
B(a)P
International Hazard
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
Fill the water bath to the depth of liquid in your reaction vessel.
|
|
|
Mateo_swe
National Hazard
Posts: 541
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
Dont you have a lab stand, the heavy base with a metal rod that you attach clamps for the flasks, condensers etc..?
If not, just make a DIY one.
If the flask is securely held in place you reduce risk off accidents happen.
Preferely the flask is held securely with clamps on lab stand and the heating bath and hotplate is put on a jack so its adjustable in height.
If you dont have the gear just invent some DIY solution that does the same.
|
|
|
mackolol
Hazard to Others
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
| Quote: Originally posted by Chemorg42 | | OK, I will probably pick up a cheep kitchen hotplate. Now another question, can I put my glassware directly on the hotplate, or should I put wire
gauze between them? |
For all my chemical life I have always put my flasks directly onto the surface of the hotplate and it went well I didn't have problems just because it
was touching its surface. I used sand baths for some time, but I often had the problem of the flask not touching the bottom of the pot, which resulted
in not proper heating. Water bath is impractical in most cases as it only has the temperature of 100C which is quite low.
For now, instead of using baths, I insulate my aparature using aluminium foil and it's really working.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
