LuckyWinner
Hazard to Others
Posts: 163
Registered: 27-8-2018
Member Is Offline
|
|
Best Lightweight Portable Mini Vacuum Pump ?
Hello everyone,
I need to vacuum distill an oil with a boiling point of 295 C.
the pump should pull a strong enough vacuum to lower this to 140 C max.
https://www.sigmaaldrich.com/chemistry/solvents/learning-cen...
5.45 mmhg or 7.26 mbar of vacuum is needed, according to this calculator.
my flask has 250ml/500ml of volume.
My prerequisites :
-Relatively quiet
-LIGHTWEIGHT not 12kg,6kg if possible under 2kg max
-vacuum gauge
-Pulls a steady vacuum (not keen on fluctuations)
-Ability to run continuous for several hours
-Chemical resistance
-pumping speed does not matter
-NO WATER ASPIRATOR
-NO chinese fridge AC rotary vane pumps, they break are loud and heavy
-price under 2000 USD
[Edited on 2-4-2020 by LuckyWinner]
[Edited on 2-4-2020 by LuckyWinner]
|
|
|
Sulaiman
International Hazard
Posts: 3697
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
https://www.youtube.com/watch?v=gGtYlS1ihbE&t=70s
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
dicyanin
Hazard to Self
Posts: 57
Registered: 29-3-2020
Location: Europe
Member Is Offline
Mood: inquisitive
|
|
neat, but I doubt it will pull 5mmHg ?
What about this? Yes it's cheap Chinese but it'll do the job.
sic transit gloria mundi
|
|
|
LuckyWinner
Hazard to Others
Posts: 163
Registered: 27-8-2018
Member Is Offline
|
|
looks good on video but...
i googled some scienmadness threads about these type of pumps and came up with this
http://www.sciencemadness.org/talk/viewthread.php?tid=9782
' Peristaltic pumps are designed for pumping liquids, they suck at vacuum production. Well, they don't suck well enough. '
...
did you successfully reproduce what is seen in the video?
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
It his video.
Why would he bother to reproduce it???
It is now time to edit your post so you look like you were paying attention.
|
|
|
LuckyWinner
Hazard to Others
Posts: 163
Registered: 27-8-2018
Member Is Offline
|
|
Quote: Originally posted by SWIM  | It his video.
Why would he bother to reproduce it???
It is now time to edit your post so you look like you were paying attention. |
to check if its valid and actually working as seen in the video for a longer period of time...
and not just for a couple seconds...
obvious...
|
|
|
Lion850
National Hazard
Posts: 517
Registered: 7-10-2019
Location: Australia
Member Is Offline
Mood: Great
|
|
Hi Dicyanin I use a Value vacuum pump, maybe a bigger model than shown in your picture. These are made for air conditioning service personnel. They
pull a great vacuum, mine often boils solutions at 45 ambient temp. But they don’t seem to be chemically resistant as mine show signs of internal
corrosion after a few months. And the pump side gets very hot when running more than 15 minutes or so.
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Search eBay for PTFE diaphragm pumps and check the spec sheets for your vacuum requirements. It's going to be really hard to find something that fits
your needs, period. Chemically resistant means a diaphragm pump and the ones that can pull <5 mm Hg are multi-head models cost $4-6k new. Examples
include Labconco 7393000, Welch 1191B series, Buchi V300, Welch 2000 series "high capacity" diaphragm pumps, etc.
It would be far cheaper to just buy a Chinese HVAC pump for $50-100 that can pull <5 mm Hg without any trouble, plus another $10 on oil to flush
the pump after use. Use a weaker vacuum source (aspirator) to strip any solvents that might hold your oil and then switch to the HVAC pump to vacuum
distill the oil.
|
|
|
BromicAcid
International Hazard
Posts: 3247
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
| Quote: Originally posted by monolithic | | Chemically resistant means a diaphragm pump and the ones that can pull <5 mm Hg are multi-head models cost $4-6k new. |
We use the Welch rotary vane pumps at work. Pull HCl, phosgene, HBr, amines, everything in the world through them. As long as you change the oil
after the fact they hold up for years and years. Unless you put them on a cart though they are certainly not portable - super heavy.
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by BromicAcid | | Quote: Originally posted by monolithic | | Chemically resistant means a diaphragm pump and the ones that can pull <5 mm Hg are multi-head models cost $4-6k new. |
We use the Welch rotary vane pumps at work. Pull HCl, phosgene, HBr, amines, everything in the world through them. As long as you change the oil
after the fact they hold up for years and years. Unless you put them on a cart though they are certainly not portable - super heavy.
|
Yes, I have an old Welch-style pump that I've torn down to bare components and rebuilt. They seem practically indestructible as long as you're not
trying to vacuum pump HCl fume and then letting the oil sit. Might not be the case with the cheaper HVAC pumps, however. And yes, they are definitely
not portable! I think mine is close to 65 pounds. 
[Edited on 4-6-2020 by monolithic]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
