Boffis
International Hazard
Posts: 1867
Registered: 1-5-2011
Member Is Offline
Mood: No Mood
|
|
N-nitroso-N-methyl-p-toluenesulphonamide
Recently I acquired some chemicals and amongst them was a jar that was labelled as this compound. It has its original label from the company that
supplied it (Koch Light) and the label states that the jar held 100g but it mentions nothing else. This compound is a well known precursor of
diazomethane and is described as a pale yellow powder, insoluble in water. It was sold as Diazald by Sigma Aldrich as it is consider less toxic than
other diazomethane precursors.
However the jar is full of a slightly viscous almost colourless, odourless, liquid which on a cold day deposit a small crop of large well formed pale
yellow crystals. When the liquid is diluted with water is turns milky white at first but on further dilution
Has anyone every used this compound? Does it decompose on keeping to a liquid? Is it deliquescent? Is it supplied as a solution? If so in what? I did
notice that one MSDS sheet described it as potentailly explosive and so I wondered if it had been shipped as a solution for safety.
Anyone have any experience of this material or a means of testing it so see if it yield diazomethane?
|
|
|
clearly_not_atara
International Hazard
Posts: 2787
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
"CH2N2 may explode in contact with sharp edges, such as ground-glass joints, even scratches in glassware.[16] Glassware should be inspected before
use and preparation should take place behind a blast shield. Specialized kits to prepare diazomethane with flame-polished joints are commercially
available."
"The compound explodes when heated beyond 100 °C, exposed to intense light, alkali metals, or calcium sulfate. Use of a blast shield is highly
recommended while using this compound."
I suppose you might consider adding KOH and covering your ears...
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
I can smell the cancer from here...
|
|
|
wg48temp9
National Hazard
Posts: 784
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
"CH2N2 may explode in contact with sharp edges"
I wounder how a sharp edge can cause it to explode. Presumable the edge catalyses decomposition and thermal runaway causes the explosion. But how can
an edge do that? I searched but found no explanation. Does anybody know the mechanism and can explain it or provide a link?
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
clearly_not_atara
International Hazard
Posts: 2787
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
If you consider the Navier-Stokes equations in presence of a sharp corner, you find that the flow rate diverges. Possibly this generates some
localized heating which acts like a spark. See e.g.
https://demonstrations.wolfram.com/FluidFlowAroundACorner/
To be fair I have only done the math for the 2D case which is much simpler thanks to the fact that R^2 has a field structure while R^3 does not.
|
|
|
wg48temp9
National Hazard
Posts: 784
Registered: 30-12-2018
Location: not so United Kingdom
Member Is Offline
|
|
Presumably the increase in temperature caused by local increase in pressure can be be calculated from the change in velocity, density and
compressibility of the fluid though given how incompressible most liquids are I would expect the heating to be less than 1C even if it is stirred
vigorously.
I thought perhaps if the surface is catalytic the intersection of two surfaces at the corner could double the decomposition which then causes the
thermal run away.
I am wg48 but not on my usual pc hence the temp handle.
Thank goodness for Fleming and the fungi.
Old codger' lives matters, wear a mask and help save them.
Be aware of demagoguery, keep your frontal lobes fully engaged.
I don't know who invented mRNA vaccines but they should get a fancy medal and I hope they made a shed load of money from it.
|
|
|
Boffis
International Hazard
Posts: 1867
Registered: 1-5-2011
Member Is Offline
Mood: No Mood
|
|
Ha guys, you are getting way of topic! I am not asking about diazomethane. I have heaps of data on the stuff and detailed descriptions of its
preparation as an ether solution, however, my question is about the specifics of one particular commercial precursor. In particular what what form it
comes in solid or solution.
|
|
|
S.C. Wack
bibliomaster
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
Rough surfaces in general.
A solution would be more unstable. Vogel should answer everything. If a sample is denitrosated, perhaps it can be restored.
|
|
|
Dr.Bob
International Hazard
Posts: 2733
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
We would dissolve it in a mixture of aq. NaOH and ether and mix for a while. The diazomethane dissolves in the ether and the rest stays in the
water, so you can use a sep funnel to separate them, and then react the diazomethane as a solution. It is stable as a dilute solution, the hazards
are much worse when it is concentrated or distilled to be pure, then it is extremely unstable to sharp edges, heat, loud noises, and near about
everything. There was special polished glassware available for that, but much simpler to just use it as a solution. If you make a small amount,
then react the solution with a simple acid, like benzoic or such and see if the methyl ester forms. We used it often to make methyl esters,
occasionally methyl ethers.
|
|
|
UC235
National Hazard
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
I think the stuff is probably long since garbage, having reverted to some sort of hygroscopic tosylate salts or tosic acid.
|
|
|
Boffis
International Hazard
Posts: 1867
Registered: 1-5-2011
Member Is Offline
Mood: No Mood
|
|
I'm inclined to agree with UC235 and this stuff has long since passed its sell-by date.
|
|
|
Dr.Bob
International Hazard
Posts: 2733
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Boffis  | | Ha guys, you are getting way of topic! I am not asking about diazomethane. I have heaps of data on the stuff and detailed descriptions of its
preparation as an ether solution, however, my question is about the specifics of one particular commercial precursor. In particular what what form it
comes in solid or solution. |
It comes as a solid. Not sure how unstable it is, but it may be hygroscopic, not sure what it would look like if wet.
Your stuff is likely crap now, but you could try to purifiy the material. It is highly carcenogenic, but it sounds like you are aware of that. Might
be easier to find some new stuff.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
