Sulaiman
International Hazard
Posts: 3697
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Accuracy of cheap volumetric flasks ?
I intend to buy a 100ml class A volumetric flask.
Pyrex : Bomex China = 5 : 1 cost ratio.
Anyone cheched the calibration accuracy of cheap Chinese volumetric flasks ?
Specifically I'm looking at
https://shopee.com.my/Pyrex-Volumetric-Flask-Class-A-Ready-S...
vs
https://shopee.com.my/Teamwinm-1pcs-100ml-Clear-Glass-Volume...
EDIT : reply to below comment by Ubya here to avoid bumping this thread......
____________________
That's pretty accurate !
I closed one eye and ordered the pyrex volumetric flask, to be reasonably confident of accuracy.
(local disctributor for scilabware=uk pyrex/quickfit, batch certificate available)
P.S. I have a selection of classA and classB volumetric flasks, packed in boxes, in uk.
I just want something to play with now (vs. my new balance),that will be useful later.
[Edited on 6-3-2020 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
well i haven't bought many volumetric flasks, i only bought a chinese 1ml one. i tested its accuracy using a milligram balance, after calibration and
zeroing it i measured 1.000+-1mg
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
Dr.Bob
International Hazard
Posts: 2734
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
The effect of the temperature on the density and the glass volume is almost as much as any variation in glass manufacturing, unless they are just
crap. The analytical chemists in my group tend to measure solvent by weight (using the known density of the solvent at a set temperature) if they
are really needing accurate amounts. My compromise is that I tend to test a volumetric flask by filling to the line and weighting before and after
to see if the actual weight matches the calulated weight. If so, then I just use the flask, if not, I can either find another flask or do it by
weight. But for 99% of what I do, a simple volumetric flask (type A) does fine. We use them for opptical rotation samples, acid/base solutions
when needed, and making standards for HPLC.
If anyone in the US wants cheap used Pyrex volumetrics I have lots, but it would cost a fortune to ship to the UK, sadly. I even have some brand new
ones in small sizes.
|
|
|
brubei
Hazard to Others
Posts: 188
Registered: 8-3-2015
Location: France
Member Is Offline
Mood: No Mood
|
|
Just ask to the seller what are the quality, certification (ISO) and measurement error associated with for the products.
Reliable sellers must know this parameters.
exemple of quality classification :
| Quote: | | Even Class A volumetric glassware is not absolute but rather has a tolerance from its stated nominal value. For example, a 25 mL Class A Transfer
Volumetric Pipet has a capacity tolerance of ± 0.03 mL, and a 50 mL Class A Buret has a tolerance of ±0.05 mL at full capacity.
|
https://www.sigmaaldrich.com/content/dam/sigma-aldrich/count...
I'm French so excuse my language
|
|
|
Sulaiman
International Hazard
Posts: 3697
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Quote: Originally posted by Dr.Bob  | | ... The analytical chemists in my group tend to measure solvent by weight (using the known density of the solvent at a set temperature) if they are
really needing accurate amounts... |
I agree that for accuracy chemicals/solvents/reactants are best measured by weight.
In this case I intend to do some density measurements so this 100 +/- 0.08 ml volumetric flask will be my reference for volume.
I would have prefered a larger size as the relative accuracy of volumetric flasks increases with increasing capacity,
but I'm limited by my balance to 220g max.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
As long as the glass is stable (and I expect it would be), you can calibrate it yourself using a balance.
|
|
|
Sulaiman
International Hazard
Posts: 3697
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
my first intention is to measure the density of water as accurately as I can 
(tap/rain/distilled, 'as-is'/boiled = six results)
I hope that the limitations to the accuracy will be ;
. temperature dependant corrections for water density and air density
. the accuracy of the volumetric flask
. weighing errors (c1mg ... when I'm patient)
and not just ;
. my techniques
______________________________________________________________
I downloaded the batch certificate for the volumetric flask ;
Attachment: 100ML.pdf (671kB)
This file has been downloaded 314 times
If on the day of production the average was 100.021ml with std.dev. of 0.014ml,
can I confidently report the capacity (at 20oC) to be 100.021 ml +/-0.014ml ?
[Edited on 13-3-2020 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
