B.D.E
Hazard to Self
Posts: 97
Registered: 5-8-2019
Member Is Offline
Mood: Oscillating
|
|
Graham condenser - explosion hazarded?
Hey there,
I recently read(somewhere in the forum) that refluxing with a Graham condenser might cause pressure buildup due to condensed liquid clogging the coil.
The explanation was that the gas pressure might prevent the condensed liquid from falling down.
Before reading about it I've ordered a soxhelt extractor with, you guessed it, a Graham condenser.
I wanted to ask if the risk is real, and if so in which cases? Also, is there anything I can do to minimize the risk down to negligible levels?
As the soxhelt extractor is expected to run for long periods of time without supervision, I obviously want to make sure it safe to use it.
Much thanks, Ben.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
don't use a gram for that very stupid idea them selecting that type IMO, use an Allihn condenser or Dimroth for best result.
https://en.wikipedia.org/wiki/Condenser_(laboratory)#Allihn_condenser
I ordered a converter to standard 24/40 for that reason.
[Edited on 25-1-2020 by XeonTheMGPony]
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
I wouldn't call it an explosion hazard so much as a potential geyser.
But I agree with the above post.
I've seen those graham type condensers on Chinese Soxhlets for some time now and I've always wondered if they work okay or not.
Nanshin makes ones like that, or at least did a couple of years ago.
When switching condensers on a Soxhlet, remember that Soxhlets are meant to reflux very fast to get the job done 'quickly', so you'll want to be sure
the replacement condenser has plenty of capacity.
Friedrichs condensers are popular, as are the much cheaper Alihns.
If you've got two Liebigs you can try using both on a Claisen adaptor.
I think that would be better than just stacking them but maybe my reasoning is off.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by SWIM  | I wouldn't call it an explosion hazard so much as a potential geyser.
But I agree with the above post.
I've seen those graham type condensers on Chinese Soxhlets for some time now and I've always wondered if they work okay or not.
Nanshin makes ones like that, or at least did a couple of years ago.
When switching condensers on a Soxhlet, remember that Soxhlets are meant to reflux very fast to get the job done 'quickly', so you'll want to be sure
the replacement condenser has plenty of capacity.
Friedrichs condensers are popular, as are the much cheaper Alihns.
If you've got two Liebigs you can try using both on a Claisen adaptor.
I think that would be better than just stacking them but maybe my reasoning is off. |
I like the Allihn's, very easy to clean, good surface area and internal volume, the volume being most important to allow the condensate to pass over
the vapor rushing in.
The Dimroth I'd be worried any bumping could rattle the tubes enough to break, same reason the gram seems like very poor selection
|
|
|
stoichiometric_steve
National Hazard
Posts: 827
Registered: 14-12-2005
Member Is Offline
Mood: satyric
|
|
I've never seen that happening. Have you?
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
I never said I saw it, I said I'd be worried.
|
|
|
B.D.E
Hazard to Self
Posts: 97
Registered: 5-8-2019
Member Is Offline
Mood: Oscillating
|
|
Thanks for the replies. I think I'll just buy another condenser(or an adapter).
I likely to be using this apparatus with ether extractions. A potential geyser of ether near an hotplate with high(ish) pressured ether-containing-RBF
on top of it... It's just too much of a risk...
I am however might check it's limits just for fun(I really curious to see how much of an issue it really is).
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Graham condensers are absolutely useless for reflux (and not very good for distillation in most cases either). Don't buy one of those. On the other
hand, a coil condenser (coolant through coiled tube, vapour around the outside of the coil) works very well.
|
|
|
morganbw
National Hazard
Posts: 561
Registered: 23-11-2014
Member Is Offline
Mood: No Mood
|
|
I use one sometimes in a vertical position as a condenser for low boiling stuff.
I have had fairly good luck.
To be sure they are not a normal condenser and as for reflux, just don't do it.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
That is their main purpose, for low boiling substances where you need high efficiency low flow.
but for much of any thing ells ya, they are crap, impossible to clean so on.
|
|
|
Texium
Administrator
Posts: 4580
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
The only thing I use my Graham condenser for is when I distill bromine or diethyl ether. It works beautifully for those, but it's overkill for
anything else that I've ever needed to distill. It's one of those pieces of glassware that if you're offered one for free, you should absolutely take
it, but unless you're planning on setting up a large scale bromine still, you don't need to go out of your way to buy one.
|
|
|
Dr.Bob
International Hazard
Posts: 2733
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
If you prefer an Allihn condenser for the Soxhlet, I have some extra conensers that fit most every size Soxhlet made. The Soxhlet's get broken way
easier, so I have extra condensers. They are the best, short of a really big reflux one or a double condenser (jacket outside and coil inside),
which I have a few of, but they are fragile and expensive. Note that using an adapter from 40/38 to 24/40 and a 24/40 condenser will almost
certainly limit you a lot, as the condenser will just be too small to work well. There is a reason that most Soxhlets have larger diameter condensers
on top, which is becasue they are needed to work well. Vapors need a lot of surface area to condense quickly.
|
|
|
Heptylene
Hazard to Others
Posts: 319
Registered: 22-10-2016
Member Is Offline
Mood: No Mood
|
|
I recommend buying a condenser with a classic joint size like 24/40 and an adapter from your soxhlet to your condenser etc. That way you can use the
condenser for other things too. I would also avoid a condenser without top joint (like the one you showed) as it cannot be connected at the top to
other glassware if you need it.
|
|
|
B.D.E
Hazard to Self
Posts: 97
Registered: 5-8-2019
Member Is Offline
Mood: Oscillating
|
|
Thanks everyone. I'm planning to buy a new condenser soon 
| Quote: Originally posted by Texium (zts16) | | The only thing I use my Graham condenser for is when I distill bromine or diethyl ether. It works beautifully for those, but it's overkill for
anything else that I've ever needed to distill. It's one of those pieces of glassware that if you're offered one for free, you should absolutely take
it, but unless you're planning on setting up a large scale bromine still, you don't need to go out of your way to buy one. |
So you claim that it's safe to use for extractions with ether? Because this is one of my main uses for the apertures.
My biggest concern was that due to the rapid boiling of ether - the condensed liquid might clog the condenser, resulting in a pressure buildup inside
the apertures until eventually it would get high enough to squirt the ether out of the condenser into the surrounding area(e.g the hotplate).
| Quote: Originally posted by Dr.Bob | | If you prefer an Allihn condenser for the Soxhlet, I have some extra conensers that fit most every size Soxhlet made. The Soxhlet's get broken way
easier, so I have extra condensers. They are the best, short of a really big reflux one or a double condenser (jacket outside and coil inside),
which I have a few of, but they are fragile and expensive. Note that using an adapter from 40/38 to 24/40 and a 24/40 condenser will almost
certainly limit you a lot, as the condenser will just be too small to work well. There is a reason that most Soxhlets have larger diameter condensers
on top, which is becasue they are needed to work well. Vapors need a lot of surface area to condense quickly. |
The smaller diameter was a concern of mine too. But after some thinking I concluded that the larger diameter is probably there just to make it easier
to get solids in and out of the extractor. And that no matter what the diameter of the condenser is, the bottle neck of the evaporation will most
likely remain the narrow tube connecting between the bottom and the top of the apparatus.
[Edited on 2-2-2020 by B.D.E]
|
|
|
morganbw
National Hazard
Posts: 561
Registered: 23-11-2014
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by B.D.E | Thanks everyone. I'm planning to buy a new condenser soon
| Quote: Originally posted by Texium (zts16) | The only thing I use my Graham condenser for is when I distill bromine or diethyl ether. It works beautifully for those, but it's overkill for
anything else that I've ever needed to distill. It's one of those pieces of glassware that if you're offered one for free, you should absolutely take
it, but unless you're planning on setting up a large scale bromine still, you don't need to go out of your way to buy one.
|
So you claim that it's safe to use for extractions with ether?
Because this is one of my main uses for the apertures.
[Edited on 2-2-2020 by B.D.E] |
I did not read the term extractions. Perhaps reread this thread carefully.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Grams are good for RECOVERING Ether by distillation or for making Bromine liquid.
For reflux based extraction Dimroth or Allihn.
|
|
|
Steam
Hazard to Others
Posts: 238
Registered: 25-3-2014
Location: Minnesota
Member Is Offline
Mood: Triple Point
|
|
I think you have your answer already, but the Graham condenser is apt to start "gurgling" and will eventually start to spew out the top if left
unchecked. It is a really poor design on their part...
Probably with some additional tubing, you could make it into a condenser for a water distiller or something :]
DISCLAIMER: The information in this post is provided for general informational purposes only and may not reflect the current law in your jurisdiction.
No information contained in this post should be construed as legal advice from the individual author, nor is it intended to be a substitute for legal
counsel on any subject matter. No reader of this post should act or refrain from acting on the basis of any information included in, or accessible
through, this post without seeking the appropriate legal or other professional advice on the particular facts and circumstances at issue from a lawyer
licensed in the recipient’s state, country or other appropriate licensing jurisdiction.
|
|
|
B.D.E
Hazard to Self
Posts: 97
Registered: 5-8-2019
Member Is Offline
Mood: Oscillating
|
|
| Quote: Originally posted by XeonTheMGPony | Grams are good for RECOVERING Ether by distillation or for making Bromine liquid.
For reflux based extraction Dimroth or Allihn. |
Got you
| Quote: Originally posted by Steam | I think you have your answer already, but the Graham condenser is apt to start "gurgling" and will eventually start to spew out the top if left
unchecked. It is a really poor design on their part...
Probably with some additional tubing, you could make it into a condenser for a water distiller or something :] |
Thanks for the advice man.
I actually used it as a "suck-back trap" and it worked quite nice(the reaction on the other hand was a complete failure).
and yes I got my answer. thanks everyone 
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
