anoopai
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 51
Registered: 27-11-2005
Location: india
Member Is Offline
Mood: No Mood
|
|
Tinning PCB
What is the easiest method to apply tin to home made PCBs ?
|
|
urbs
Harmless
Posts: 12
Registered: 16-5-2006
Member Is Offline
Mood: No Mood
|
|
IIRC, the solution that I used was Tin Chloride, a bit of sulfuric acid and Thiourea. The Tin Chloride I made since I happened to have some mossy
tin, (don't ask), and ordered the thiourea. You might be able to use one of those liquid silver tarnish removers since they have a bunch of thiourea
included. Make the solution as you need it since it won't store. Do a search for electroless tinning.
http://books.google.com/books?id=m8sJBIMtETgC&pg=PA318&a...
|
|
anoopai
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 51
Registered: 27-11-2005
Location: india
Member Is Offline
Mood: No Mood
|
|
thanks
thanks urbs , but its stannous or stannic chloride ?
|
|
anoopai
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 51
Registered: 27-11-2005
Location: india
Member Is Offline
Mood: No Mood
|
|
ok its stanous chloride
http://www.finishing.com/0200-0399/260.shtml
|
|
IrC
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2710
Registered: 7-3-2005
Location: Eureka
Member Is Offline
Mood: Discovering
|
|
I would look into electrochemical methods. I used to build hundreds of boards and the method you are looking at sucks. You need the copper super
clean, free of oxygen and hydrocarbons. Green scrubby pad (no soap type) in hexane or trichlor to clean works. After you finish it will still suck so
bad most often it actually interferes with soldering. If you plan to do many and/or of high quality learn to electroplate. But still clean well first.
"Science is the belief in the ignorance of the experts" Richard Feynman
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1310
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
I found the easiest way is to paint the board with liquid flux (essential !), then use a piece of desoldering braid, full of solder, wrapped around
your soldering iron tip, and basically paint the copper tracks with solder. Results aren't especially pretty, but with care you end up with a flat
'tinned' surface that won't oxidise, and solders very easily.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
Arthur Dent
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
This is the stuff I use:
http://www.lpkfusa.com/boardfinish/tinplating.htm
It's a mixture of fluoroboric acid, Stannous fluoroborate and thiourea. It works incredibly well. You drop any cleaned-copper PCB in this solution and
in minutes, you have a perfect, uniform coating of tin on your traces.
Robert
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
Texium
|
Thread Moved 19-11-2023 at 16:21 |