monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
How to dissolve wood?
Long story short, I'm doing essential oil extraction of wood. There's a piece of wood stuck in my round bottom flask - I guess it swelled up during
the steam distillation process. It almost fits through the neck of the flask but gets stuck, and I can't break it up or pull it out. I'm currently
letting it soak in hot (50 C) saturated NaOH with stirring. It doesn't seem to be doing much. Any other ideas?
|
|
|
SWIM
National Hazard
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
I'd try 10% bleach for a few days of soaking.
You could put the dry flask in an oven at 200 to 250C and try to carbonize it..
Concentrated H2SO4 might break it down.
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Good ideas, thanks for the quick response. I think I'll try H2SO4 first, since I have some drain cleaner sitting around.
|
|
|
WGTR
National Hazard
Posts: 971
Registered: 29-9-2013
Location: Online
Member Is Offline
Mood: Outline
|
|
I’d suggest putting it in an oven and letting it dry out. If it swells in water, then without water it shrinks again...?
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Burn it?
|
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
i dont think heating that hot is better than H2SO4. a bunch of organics like tar will stick to the flask. good luck in removing that unless you have
piranha soln.
|
|
|
DraconicAcid
International Hazard
Posts: 4333
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
Copper(II) hydroxide dissolve in concentrated ammonia will dissolve cellulose- it might help break up the wood.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
clearly_not_atara
International Hazard
Posts: 2787
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Ding ding ding! This is the original rayon process. It isn't used anymore because avoiding copper contamination of effluent is hard --
Cu(NH3)22+ is very stable and its salts are highly soluble.
There are also ionic liquids that can be used for dissolving cellulose. The anion is usually acetate, since it is a good H-bond acceptor. Cations are
often imidazolium, though morpholinium, amidinium and choline have been used. Choline acetate in particular is accessible to the amateur, as is the
DES choline chloride-urea. See:
https://onlinelibrary.wiley.com/doi/abs/10.1002/chem.2011032...
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Thank you everyone for the interesting ideas. Some hot H2SO4 drain cleaner did the trick. 
|
|
|
Mabus
Wiki Master
Posts: 238
Registered: 3-11-2013
Member Is Offline
Mood: Energetic
|
|
Glad to hear. Sulfuric acid works best I see.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Wood is disintegrated in pulp mills using aqueous NaOH/Na2S (Kraft process) at about 180°C for 3 hrs under pressure. This dissolves the lignin that
binds the cellulose fibers together.
I would try heating it in aqueous NaOH (~25%) as hot as possible for a few hours.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
