Polverone
Now celebrating 21 years of madness
Posts: 3186
Registered: 19-5-2002
Location: The Sunny Pacific Northwest
Member Is Offline
Mood: Waiting for spring
|
|
ethylene glycol
I would like some of this compound to experiment with. Ideally, as with all chemicals, it should be inexpensive, readily obtained, and pure. But
I'll take what I can get.
Is antifreeze truly the best/only OTC way (assuming that I don't want to start from ethylene)? I've seen some indication that there may be
brake fluids that contain it, but the few MSDS I have looked at indicated complex mixtures.
PGP Key and corresponding e-mail address
|
|
|
BromicAcid
International Hazard
Posts: 3245
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Well if you did want to start from ethanol and go to ethylene you could react ethyl alcohol with a paste of concentrated H2SO4 with sand at
high heat to yeild ethene. Then bubble the gas though a basic solution of potassium permanganate to get your ethylene glycol.
HOCH2CH3 --H2SO4--> CH2CH2 + H2O
CH2CH2 --KMnO4 / OH--> OHCH2CH2OH
But if you just want to get your ethylene glycol from OTC sources I really can't help you there, I know nothing about purities or brands or
anything.
[Edited on 2/11/2004 by BromicAcid]
|
|
|
leopard
Harmless
Posts: 12
Registered: 14-11-2002
Member Is Offline
Mood: No Mood
|
|
ethylene glycol
Polverone I did an MSDS search of several brands of anti-freeze a while back and found that the more expensive "Brand Name" ones (eg.
PRESTONE) were about 90% pure with the remainder comprised of water, anti-rusting agents, anti-gelling agents etc. The lesser known low cost brands
(eg. PEAK brand) were 95% pure with less of the additives. I found the PEAK brand worked fine for EDN.
|
|
|
Haggis
Hazard to Others
Posts: 238
Registered: 1-12-2002
Location: Mid-America.
Member Is Offline
Mood: Lacrymating
|
|
I remember reading a while back on the E&W that NBK had aquired EG in relatively pure amounts with only a slight methanol contamination in the
form of antifreeze. The thread discussed nitrogen mustards, IIRC.
One could easily distill over the methanol for relatively pure EG. What are you going to use it for? Is it something in which a dye wouldn't
matter, or is it something a bit more sensitive?
Great ideas often receive violent opposition from mediocre minds.
<b> <a href=\"http://pgp.mit.edu:11371/pks/lookup?op=get&search=0xEE41A2B1\">PGP Key</a> </b> 0C0A 7486 B97F
92EE AE50 A98C A4F3 087E 8CE9 A782 |
|
|
chemoleo
Biochemicus Energeticus
Posts: 3005
Registered: 23-7-2003
Location: England Germany
Member Is Offline
Mood: crystalline
|
|
How about using any antifreeze, evaporating any water off with heat (ethylene glycol has a boiling point of 198 deg C - so you will get rid off most
other volatiles before that), and THEN adding H2SO4/H3PO4 to form dioxane (reflux)?
Dioxane distills off at 101.5 deg C. This way you should get rid off 1) all low boiling volatiles and 2) distill off dioxane after other volatiles
were removed.
After the reaction, the ethyleneglycol can be recovered by refluxing the solution in NaOH - at high purity.
PS I have to admit though that I have no backup on the NaOH de-etherification - but on the other hand I don't see why it shoudn't work!
Sounds like a nice method to me anyhow!
Never Stop to Begin, and Never Begin to Stop...
Tolerance is good. But not with the intolerant! (Wilhelm Busch)
|
|
|
Pyrovus
Hazard to Others
Posts: 241
Registered: 13-10-2003
Location: Australia, now with 25% faster carrier pigeons
Member Is Offline
Mood: heretical
|
|
I read somewhere about how methane can be prepared by heating sodium acetate with sodium hydroxide:
CH3COONa + NaOH -> CH4 +Na2CO3.
Perhaps an analogous reaction with sodium tartrate could be used to prepare ethylene glycol:
Na2 OOC-CH(OH)-CH(OH)-COO +2NaOH -> (CH2OH)2 +2Na2CO3?
|
|
|
Hermes_Trismegistus
National Hazard
Posts: 602
Registered: 27-11-2003
Location: Greece, Ancient
Member Is Offline
Mood: conformation:ga
|
|
Ethylene Glycol
Commonly used in those radiant heating systems they use in concrete builings.
Comes delivered in large drums. Just says ethylene glycol on the MSDS. Had to move some once on a building site. Safety regs say we get to read MSDS
on every chem we come into contact with. I just used it as an excuse to catch my breath for five minutes.
Arguing on the internet is like running in the special olympics; even if you win: you\'re still retarded.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
