| Pages:
1
2 |
Morgan
International Hazard
Posts: 1694
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
https://www.osha.gov/SLTC/toluene/health_hazards.html
|
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
1 )Ask your local authorities how you can deal with the problem before it comes back to bite you (legally). You cant expect to incomodate hundreds of
people without payback.
2) Dont ask ScienceMadness members as they'll recommend being cautious.
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by beerwiz  | Most of the smell is generated when pouring from one container to the other and during the buchner filtration when the vacuum pump dissipates all the
VOC's all over the place.
|
Why not switch the pump off?
Once it has pulled the air out of the flask then all it can do after that is pump vapour and upset the neighbours.
|
|
|
clearly_not_atara
International Hazard
Posts: 2789
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Consider using different solvents? I'd be surprised if ethyl acetate were causing these problems but toluene/chlorocarbons/etc certainly will.
| Quote: Originally posted by VSEPR_VOID | | The only reason you are using gallons of solvents that would seem reasonable would be if you were preparing drugs. Dont you have posts about
extracting alkaloids? I dont care either way but at least spill the beans on what you are doing. Also please dont gas your neighbors well doing it.
|
Any drug manufacturer ought to have sufficient capital to procure a better venue. You can make gram quantities of most drugs operating on a much
smaller scale than that.
[Edited on 3-1-2019 by clearly_not_atara]
|
|
|
Sigmatropic
Hazard to Others
Posts: 307
Registered: 29-1-2017
Member Is Offline
Mood: No Mood
|
|
To remove traces of nasty volatile organic compounds consider leading the off-gasses into something like a catalytic oxidiser, a furnace or an engine
(as was suggested further up in this thread). The catalytic oxidiser method is shown in the video linked below. But be carefull to avoid the explosion
mentioned in the video, so be sure to check out the recommendations at the end of the video.
https://www.youtube.com/watch?v=_2UnKLm2Eag
|
|
|
clearly_not_atara
International Hazard
Posts: 2789
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Actually one thing that should work pretty well is venting the exhaust through a big container of a low-volatility solvent that dissolves everything.
I think polyethylene glycol (PEG 400 or maybe 600) would be particularly suitable.
After a while though you're gonna have one nasty bucket of polyethylene glycol. Presumably this can be disposed of by combustion.
[Edited on 5-1-2019 by clearly_not_atara]
|
|
|
zed
International Hazard
Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Yup! Folks are complaining? Stinking up the neighborhood? Got laws against that.
You are in legal jeopardy.
Figure out how to cool and trap those vapors.
Dry ice ? An expensive solution, but better than an ominous knock on the door, followed by exorbitant legal fees.
|
|
|
lordcookies24
Hazard to Self
Posts: 78
Registered: 2-1-2019
Location: pluto
Member Is Offline
Mood: curious
|
|
i am not exactly mr. safe myself but if you want to deal with gallons on top of gallons of solvent, just don't do it in a residential area.
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
