beerwiz
Hazard to Others
Posts: 128
Registered: 6-2-2014
Member Is Offline
Mood: No Mood
|
|
How to dry tartaric acid to make it anhydrous?
How to dry tartaric acid to make it anhydrous?
I tried drying it in the microwave for 5mins on high but it turned brown and started boiling, probably caramelized?
What's the best way of removing all water from tartaric acid to make it anhydrous?
|
|
|
j_sum1
Administrator
Posts: 6320
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
What organic solvents does it dissolve in?
My instinct would be to use a Dean Stark trap – the same as you do for oxalic acid (using toluene as a solvent). (Here is Nile Red. Here is Nurdrage[.)
|
|
|
beerwiz
Hazard to Others
Posts: 128
Registered: 6-2-2014
Member Is Offline
Mood: No Mood
|
|
It's soluble in water, methanol, and slightly soluble in acetone.
|
|
|
j_sum1
Administrator
Posts: 6320
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
What about ethanol?
The problem with using methanol is that there is no azeotrope with water.
You might also have success with vacuum dessication or the use of a dessicator.
|
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
The situation with oxalic acid is like this: PhMe dissolves neither oxalic nor H2O. If one can use azeotropic distillation using PhMe to dehydrate
oxalic then what about other combinations of hydrates and immiscible solvents? There are plenty others to choose from, like DCM, EtOAc or EtOH but I'm
not sure if tartaric will react with alcohols, acids or esters under such conditions, and Clevenger apparatus is needed for DCM.
|
|
|
monolithic
Hazard to Others
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Maybe this is a dumb question, but wouldn't a conventional (non-microwave) oven at 120-130C for a few hours also work?
|
|
|
UC235
National Hazard
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Microwave ovens with chemicals are almost always a bad idea. It's not good to run them against very little load and since your compound is polar it
will continue heating it to decomposition even after any water of hydration is gone. Not to mention they don't heat evenly. I've melted glass in a
microwave by accident trying to dry calcium chloride before.
A conventional oven a healthy margin below the decomposition point of the anhydrous compound is the way to go, as monolithic suggested. If you can
find a decomposition temp for the hydrate listed somewhere, try to stay a good amount above that.
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Microwaves are my favorite in the lab, sodium sulfate and magnesium sulfate for example are dried in a minute when put in a glass bowl with a glass
bowl inverted on top as a lid.
The dry salts don't absorp microwaves and don't heat any further while being dry.
Oxalic acid dihydrate also works fine but sublimes from bottom to top glass, so not to much can be dried at a time. And the glasses should closely fit
|
|
|
ErgoloidMesylate
Banned
Posts: 89
Registered: 8-8-2022
Location: Norad
Member Is Offline
Mood: Freedom of thought is priceless - You can't afford it
|
|
Quote: Originally posted by beerwiz  | How to dry tartaric acid to make it anhydrous?
I tried drying it in the microwave for 5mins on high but it turned brown and started boiling, probably caramelized?
What's the best way of removing all water from tartaric acid to make it anhydrous? |
Vacuum drying at 70 c.
Cannula transfer and cannula filtering is used for lysergic synth Compressed air and remove co2
|
|
|
Texium
|
Thread Moved
14-9-2023 at 08:00 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
