Search |
[Next Page] |
LL8 from Dr. Liptakov Yes, but at inner diameter 6 mm is effect Misnay-Schardin minimal. A lot commerce tubes has flat bo ... |
15-4-2024 at 05:09 by: Laboratory of Liptakov |
Nickel aminoguanidine diperchlorate
Add water ammonia by drop after mixing Ni(ClO4)2 and AGu*HClO4 to pH=7.5...8:
Ni(ClO4)2+2AGu*HClO ... |
15-4-2024 at 00:36 by: Laboratory of Liptakov |
Nickel aminoguanidine diperchlorate I feel that will partially created Diamine nickel perchlorate. Which is relatively weak salt on ener ... |
13-4-2024 at 21:30 by: Laboratory of Liptakov |
TeACN I am afraid that this mixture will not works at this high density at all. Because TACN + 5% Al prov ... |
12-4-2024 at 23:35 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov Do whatever you want, but the open end of the tube gives the best results. When set vertically.....: ... |
12-4-2024 at 05:20 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov Why wait 30 minutes when you can have an exit segment in the cavity pressed in 30 seconds. You're ju ... |
10-4-2024 at 22:12 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov Your stainless steel is the best cavities for filling of any EM. If you use good pressed ETN, witho ... |
10-4-2024 at 07:13 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov Nice cavity. And cheap cavity. Thanks for link. Stainless steel is very solid. But for testing brisa ... |
8-4-2024 at 22:37 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov Military NC it may (or may not) contain antidetonation additing. Is necessary (for first attempts) ... |
8-4-2024 at 12:34 by: Laboratory of Liptakov |
Det Cap Strategies Lead block has universal using. For example for blacksmith method creating copper cone. Source of me ... |
7-4-2024 at 22:17 by: Laboratory of Liptakov |
Exotic Primaries - Complex Salts When I reading last problems about hydrazine, respectively about NHN, maybe will better focusing on ... |
7-4-2024 at 02:35 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov Best are grain 2x2 mm. Yes, can be used fuse ignition. No doped with pyrogen. Yes, k-dichromate can ... |
31-3-2024 at 21:50 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov Not. Nitrocelite is weak for initiation any mixture on AN base. |
30-3-2024 at 23:00 by: Laboratory of Liptakov |
NHN based improved primary composition Etanol described it perfectly. Nothing else to say.... |
26-3-2024 at 03:08 by: Laboratory of Liptakov |
Unconventional Shaped Charges I grabbed some old picture for construction EFP with results. Distance between liner and target was ... |
22-3-2024 at 23:49 by: Laboratory of Liptakov |
Unconventional Shaped Charges Also you can try normal steel and do it 3x annealing. Heating by PB on red color shining and insert ... |
21-3-2024 at 10:20 by: Laboratory of Liptakov |
Det Cap Strategies I estimate, that steel plate is only 1mm of thickness. Is it slim plate. For 0.6g output ETN is nec ... |
17-3-2024 at 23:35 by: Laboratory of Liptakov |
Oxidizer/2-EHN emulsions For first attempt mixing 79% dry anhydrous NaClO4 + 21% EHN + 5% dH2O. Heated on 70 C, mixing, coo ... |
13-3-2024 at 02:20 by: Laboratory of Liptakov |
Det Cap Strategies For mixture 1:1 is tapping not good idea. Because fine powder NHN fall down. Mixture will apparted p ... |
10-3-2024 at 23:27 by: Laboratory of Liptakov |
Det Cap Strategies Video is basically professional guide. Final pressing assemble is best what I saw ever. Thick wooden ... |
9-3-2024 at 07:55 by: Laboratory of Liptakov |
6km/sec VOD From Cast NaCLO4 Composition Paints content by important order: Water, senzitizer, binder, colorant. Activated matrix by nitrate ... |
2-3-2024 at 00:29 by: Laboratory of Liptakov |
Det Cap Strategies If you use wet sawdust, 2 short boards and a brick on the boards will serve (and will be enough) as ... |
1-3-2024 at 08:30 by: Laboratory of Liptakov |
LL8 from Dr. Liptakov pjig.....Yes, usually the padding design is as per your description. Nothing epoxy based. Only the a ... |
29-2-2024 at 11:11 by: Laboratory of Liptakov |
Det Cap Strategies Mikrotek said all important. You finally leave the casting ETN..... |
29-2-2024 at 03:39 by: Laboratory of Liptakov |
Det Cap Strategies ManyInterests.......The output segment does not need to be push to 20 Kg. It is enough to manually p ... |
27-2-2024 at 23:35 by: Laboratory of Liptakov |
[Next Page] |