Search |
[Next Page] |
Semicarbazide ---> Sodium Azide NaN3 method Hahaha that reply made me laugh Philou.
Just perform the hydrazine synthesis step outside if yo ... |
4-7-2017 at 09:23 by: greenlight |
How do you powderise substances? Buy a ball mill and chuck what you need powdered in it for an hour or two provided it isnt anything ... |
17-6-2017 at 19:05 by: greenlight |
New chemicals for sale ! I just received a 5th successful order of a hard to obtain chemical from mario.
10 out of 10 as usu ... |
6-6-2017 at 22:33 by: greenlight |
Exotic thermites & analogs I have done some tests with magnalium thermite before and took photos.
I had a similar ratio to the ... |
24-5-2017 at 23:53 by: greenlight |
How should I treat TATP? Just thought I would put this up. It's a friction sensitivity results graph for common primaries th ... |
20-5-2017 at 01:17 by: greenlight |
EGDN or PLX The PLX would be easier to manufacture as you just mix the two liquids together.
EGDN is not a bina ... |
18-5-2017 at 22:50 by: greenlight |
Short question / quick answer - Thread It is quite hard to find any test results for ETN as no one has really conducted many. Probably due ... |
9-5-2017 at 06:53 by: greenlight |
Electrical ignition system The first 4 there was no delay at all.
I think the batteries get drained pretty fast. |
25-4-2017 at 05:38 by: greenlight |
initiation system success Thanks NP I did end up getting the wire there. I purchased 30 metres of 14 gauge wire and finished ... |
25-4-2017 at 03:18 by: greenlight |
Electrical ignition system They look very small compared to standard gauge here.
What diameter in mm are the 16 gauge det line ... |
24-4-2017 at 07:16 by: greenlight |
Electrical ignition system I think I will definitely use steel wool instead of nichrome for the electric caps.
I have wired ... |
23-4-2017 at 22:46 by: greenlight |
Electrical ignition system Yes the LED is rated at 12V. I will purchase a 1K resistor and wire it according to the latest draw ... |
18-4-2017 at 10:25 by: greenlight |
Electrical ignition system Okay I will go purchase a 2K resistor.
It will go on the positive side of the LED on the right side ... |
17-4-2017 at 18:42 by: greenlight |
Electrical ignition system Okay then I will have to purchase one. Would that be connected right before the LED after the conne ... |
17-4-2017 at 09:52 by: greenlight |
Electrical ignition system Okay so without the test button and just having a two connection safety switch, LED and fire button ... |
17-4-2017 at 08:36 by: greenlight |
Electrical ignition system So I should add another led light to show that there is power?
I am still a bit sketchy on the ex ... |
16-4-2017 at 07:30 by: greenlight |
Electrical ignition system I have the switches installed and it is ready to wire up but I have one question.
In the diagram th ... |
15-4-2017 at 22:50 by: greenlight |
Cheap nitrates to potassium nitrate If you want to use calcium nitrate I think it would be preferable to react it with potassium sulfate ... |
11-4-2017 at 21:40 by: greenlight |
Exotic Primaries - Complex Salts Excellent work Neonpulse, I can't find any information on Cesium picrate at all except for what you ... |
7-4-2017 at 02:19 by: greenlight |
Ammonium perchlorate without DIY anodes? No the power supply is 5 volt 20 amp.
I did purchase a power meter but it requires a shunt to run ... |
2-4-2017 at 21:00 by: greenlight |
metered perc cell update I wired the whole system together and ran it but the amps are reading wrong.
With some help from WS ... |
31-3-2017 at 22:36 by: greenlight |
Electrical ignition system I have purchased most of the parts to make the ignition system. I will start wiring it together in ... |
31-3-2017 at 22:32 by: greenlight |
Electrical ignition system Okay thats extremely important because my site has large high voltage power lines a couple hundred m ... |
31-3-2017 at 05:38 by: greenlight |
Electrical ignition system Twist the wires together you mean until ready to fire?
[Edited on 31-3-2017 by greenlight] |
30-3-2017 at 23:18 by: greenlight |
Electrical ignition system @xeon, I will attempt to use the diagram with 14 gauge wire and two 9 volts in a series for power an ... |
30-3-2017 at 20:13 by: greenlight |
[Next Page] |