The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
Calcium cyanurate ---> Cyanamide
Relavent previews from thread I did not want to hijack:
https://www.sciencemadness.org/talk/viewthread.php?tid=2762
Rosco quotes:
Quote: |
After filtering and drying , the calcium cyanurate should
yield calcium cyanamide upon heating to decomposition at red orange heat in the absence of air by the following reactions :
CaH(OCN)3 ---> Ca(OCN)2 + HOCN
Ca(OCN)2 ---> CaC(N)2 + CO2 |
Quote: |
A second experiment has been done on a 1 mole scale to
produce the hoped for calcium cyanurate . In a 4 liter beaker containing 3 liters of stirred hot water was added
165 grams cyanuric acid dihydrate . After 10 minutes most
of the cyanuric acid was dissolved and to the stirred suspension was added 80 grams solid NaOH . After another 15 minutes there was added a solution
of 110 grams CaCl2 in 500 ml hot water and the stirring continued for 30 minutes . After standing and cooling overnight the mixture was filtered
through cloth and the
cloth gathered and twisted down to squeeze excess
liquid as much as possible from the solids which compacted to a dense ball of microcrystalline and
slightly damp material which should air dry easily
when broken up . |
Calcium cyanurate was made on a 1/3mol scale, using the procedure Rosco posted, however more water was necessary to dissolve all cyanuric acid.
The cyanurate was allowed to dry on a windowsill for 2 weeks, at which point it was easily powdered.
Thermal decomposition:
34.1g of the cyanurate was added to a 42.8g metal can with a tight fitting lid. The lid had a dozen or so 1mm holes punched in the lid. 34.1 g was
only chosen as that was about the half filledmark on the can. Not sure where to get more of those cans, it was from zinc powder purchased at dye
store in vancouver a few years ago.. It was essentially a very small metal paint can, 2" tall and 3" wide. Assuming the above reactions above are
correct, after decomposition the can+cyanamide should weigh 59.1g. The can was wrapped in copper wire and a length attached to serve as a handle.
A good sized campfire was made, and the can put in at the bottom on the coals. It was left there for a couple hours occasionally shaking it around a
bit, and adding more wood to the fire. Meanwhile hotdogs were roasted away from the can
When the flames of the fire were just right, you could see flames being emitted from the holes in the lid of the can(cyanuric acid burning off). At
this point the can was a dull red. About 30 min later, flames from the can-hole were no longer noticable. A couple marshmallows were roasted, and
then the fire maintained for 40min to 1h more. The fire was allowed to die down and the can removed and left to cool. When it was cool the can was
noticibly degraded, the outer lay of metal on the can was flaking off. It weighed 55.2g. Metal flakes cracked off upon opening the can, and when the
can was open a pure white powder was seen. Few bits of charcoal got in through the holes, but nothing sugnificant. The white powder was weighed and
it weighed 11.4g. Slightly less than the 12.4g predicted, but that could be because cyanurate was damp.
Just based on the numbers it does look like cyanamide was produced, but I'll analyse it somehow, soon hopefully.
Calcium Cyanamide, all OTC
PS: Rosco, whats the referance for the cyanurate decomposing to cyamamide?
[Edited on 4-6-2007 by The_Davster]
|
|
Rosco Bodine
Banned
Posts: 6370
Registered: 29-9-2004
Member Is Offline
Mood: analytical
|
|
Campfire Cyanamide YeeeeHaaa !
And it should be reagent purity if my guess is right .
Making some tetracene or something else interesting would
be the ideal test to see if you've got what you think you've got Probably
could find some perfect tests for identifying this material .....over in the tetrazoles thread
I tried that brute force approach myself with the urea
and lime and charcoal mixture before figuring out
the cyanurate route would be better . What I used was a stainless steel chefs sized salt shaker with a threaded lid . It had one of those rotating
perforated plates that covers up the sprinkling holes to keep the salt dry when you aren't using it . I just rotated the plate to cover the holes ,
knowing it would keep out any ashes , but wouldn't be pressure tight so it would vent fumes from inside . It was a cannister about 2 1/2 inches
diameter by 4 inches tall , and I made a steel band to hold it to the end of about a six foot piece of tubular steel for a handle to stick it in the
coals . After glowing in the fire at a nice orange heat for an hour , even the stainless didn't hold up . The metal was so embrittled that when I
tried to unscrew the lid , the threads snapped off and left simply the unthreaded portion of the cannister . Nothing but a one time use even for a
stainless container ....with that crude mixture anyway and as much heat as I was using .
It was hot enough to make graphite from the charcoal
in the mixture . And it was a black mess that I haven't even attempted to use that came out of that preliminary experiment .
Yeah , I had a feeling it might work a lot better with the
calcium acid cyanurate .....no side reactions and a pure white product that can only be one thing so long as it was heated hot enough long enough to
complete the reaction . It should be a quantitative yield for cyanamide .
It might even work with no cyanic acid byproduct and
a better yield if the calcium normal cyanurate was used ,
that is if the Ca3 dicyanurate even exists IIRC it does exist and you would
simply need to adjust the stoichiometry for the precursors to get the normal Ca3 dicyanurate instead of the Ca Hydrogen Cyanurate .
I was sort of hedging my bet by going with the Ca acid cyanurate because of betting there would be some residual moisture in the precursor ....which
is poison
for the reaction ....but if there is some excess cyanic acid present ( as there is plenty excess using the Ca acid cyanurate precursor ) then it will
be involved in a mutual decomposition with any trace water , and protect the
pyrolysis reaction by thoroughly dessicating and guaranteeing the purity of the calcium cyanate intermediate , preventing any water vapor from
decomposing it before it can further decompose as planned from dry heat alone , to form the desired calcium cyanamide .
You could probably balance the reaction out so that
90% of the precursor is the normal Ca3 dicyanurate ,
and maybe have 10% of the Ca acid cyanurate present
as insurance against any residual moisture ....and still be just fine so long as the precursor is baked out good , and kept dry in storage before the
pyrolysis .
I'll have to look up the relevant patent numbers again .
I thought I already posted the patent references in the other threads . I didn't have a patent specifically for
this method , but it was shown that calcium cyanurate
was an intermediate in the reactions described in patents
that describe the urea plus lime reactions . And it was mentioned in passing in the text of a couple of those patents also that it could be done this
way using cyanurates or cyanates as higher intermediates , if
the purity of the end result was more important than
the economics of using cheaper urea . This is the
modification on the fertilizer grade process that you would
use to produce a reagent grade material for use in synthesis , rather than just making tons of something crude and impure to dump on a field as
fertilizer .
Something like an empty propane cylinder might make a decent pyrolysis chamber . I removed the valve stem which is a shrader valve like the valve
stem on a tire from an empty disposable propane cylinder , and drilled the hole out and tapped it for 1/4 " NPT , so a pipe nipple could screw into it
and a long piece of larger water pipe could be used for a handle .
I screwed a short section of 1/4" pipe nipple into a reducer coupling and drilled vent holes in the sloped bell of the coupling so fumes exit in the
fire and don't travel all the way through the handle which is capped off at the end .
The safety filler valve on the shoulder of the cylinder was also
drilled out and a stainless screw having a lengthwise groove
cut across the thread was screwed into that opening . The idea there was for a combination overpressure blowout plug and vent .
I haven't used this contraption yet , but it is about 3/4 of a liter capacity and thicker steel than a paint can , plus it can be rolled in the fire
easily to tumble the contents . It is good to know the reaction product is loose powder and not some
rocklike clinker . So once the reaction is complete , it is like
pouring out an hourglass ....instead of time for a hammer and chisel to remove the product . BTW the calcium cyanamide is definitely air and moisture
sensitive , so like calcium carbide , you should seal it up good for storage in a quality jar to keep atmospheric moisture away from it .
[Edited on 5-6-2007 by Rosco Bodine]
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
Quote: | Originally posted by Rosco Bodine
Making some tetracene or something else interesting would
be the ideal test to see if you've got what you think you've got Probably
could find some perfect tests for identifying this material .....over in the tetrazoles thread
|
Tetrazoles later, I want purity data 98%, 99% or whatever it is. I may compare
with commercial Ca-cyanamide from a supplier if I can scrounge some up at work.
Really, if you go the hydrazine route from here, you are a one pot reaction away from 5-ATZ But I have prefered transformations that avoid the hydrazine...but more work
Quote: | Originally posted by Rosco Bodine
It is good to know the reaction product is loose powder and not some
rocklike clinker . So once the reaction is complete , it is like
pouring out an hourglass .
|
Yes the powder is very fine, and if it is not, it is easily broken up. A few lumps remained after the heating, and I was worried they would be hard
as well, but it is the most easily powdered material I have come across. It is of extremely low density.
Funny thing is, urea and charcoal would likely cost me more than for cyanuric, NaOH, and CaCl2, all but NaOH available at the hardware store in
quantities not less than a kilo for under 10$.
I bought a ~1L paint can, could probably make over 500g at once in it, but a vessel that size would require bigger fire, and longer heating so the
thin metal may fail. So it will probably go unused. a 100 or 150g(cyanurate) reaction would give me all the Ca-cyanamide I would ever need anyway.
I should post a pic of the sorry state the little paint can is in. Need a new vessel now too
|
|
Rosco Bodine
Banned
Posts: 6370
Registered: 29-9-2004
Member Is Offline
Mood: analytical
|
|
If you held a good steady red heat for an hour ,
then its a good bet you have pure cyanamide @ 99+%
purity . The only hitch would be that it needs to be anaerobic pyrolysis , because if too much air got to the glowing hot cyanamide , it would just
oxidize to being burnt lime .
So you don't want too many vent holes , nor an open container ....but something that will trap the last bit of evolved CO2 inside as something of a
protective atmosphere .
Looks like another good one for the upgraded Wiley
volumes
Possibly a simple furnace something like was mentioned in another thread using a couple of flower pots
to make a clamshell chamber , and a large Humboldt Meker type lab burner in an enlarged drain hole underneath would be sufficient for a crucible
furnace that would get to the red to red orange heat that would be good . A clay piped triangle support for the crucible , maybe a fiberglass or
rockwool wrap around the outside of the pots to help insulate the furnace a bit . Or just build a box furnace from marinite panels and some screws
and angle iron as a sort of low range burner fired kiln .
A metal bucket lined with kaowool or some refractory would also do it . Any elementary furnace should get
hot enough .
|
|
roamingnome
Hazard to Others
Posts: 363
Registered: 9-9-2006
Member Is Offline
Mood: No Mood
|
|
time for some hotdogs for me..... thanks... at the end of summer its sale time on this stuff too
http://www.jbc.org/cgi/reprint/32/3/297.pdf
although it is just a web link, their lab was happy with this procedure when needing cyanamide from the calcium salt
+++++++++++++++++++++++++++++++++++++++++++
Syntheses and Structures of Metal
Cyanamide Compounds
http://deposit.ddb.de/cgi-bin/dokserv?idn=966164989&dok_...
the book!
Question
what is the reactivity difference between sodium or calcium cyanamide in anyones opinion?
+++++++++++++++++++++++++++++++++++++++++++
http://www.cyanamide.com/content/reactions.htm
pH will be a player in reaction pathways....
[Edited on 20-9-2007 by roamingnome]
[Edited on 21-9-2007 by roamingnome]
|
|
Hilski
Hazard to Others
Posts: 197
Registered: 13-9-2006
Member Is Offline
Mood: No Mood
|
|
Quote: | and to the stirred suspension was added 80 grams solid NaOH |
Just out of curiosity, would KOH be as effective as NaOH in this role? Or is the sodium required for this reaction to work?
\"They that can give up essential liberty
to obtain a little temporary safety
deserve neither liberty nor safety. \"
- Benjamin Franklin
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
The purpose of the base is to simply deprotonate the cyanuric acid, forming the alkali salt, followed by the calcium salt to precipitate the calcium
cyanurate.
KOH would work, but you may need more water depending on the solubility of the intermediate potassium cyanurate.
No procedural changes are really necessary, just get the required molar ammount of KOH and add it to the hot suspension/solution of cyanuric acid, and
add water to it if after a while in hot basic solution the cyanuric acid has not dissolved. Ammount of water is not too critical, the latter calcium
cyanurate is very insoluble.
|
|
Rosco Bodine
Banned
Posts: 6370
Registered: 29-9-2004
Member Is Offline
Mood: analytical
|
|
Quote: | Originally posted by roamingnome
time for some hotdogs for me..... thanks... at the end of summer its sale time on this stuff too |
Time for a calcium cyanurate cookout ?
Quote: |
Question
what is the reactivity difference between sodium or calcium cyanamide in anyones opinion?
+++++++++++++++++++++++++++++++++++++++++++
[Edited on 21-9-2007 by roamingnome] |
IIRC the sodium salt is more stable in solution , whereas
the calcium salt is very subject to hydrolysis .
BTW....
Those above references seem to be woefully incomplete ......
as they are all totally lacking any reference whatsoever to
Rosco's good old country campfire / furnace / pottery kiln recipe for pure calcium cyanamide , another shake and bake grocery store precursors production
[Edited on 22-9-2007 by Rosco Bodine]
|
|
chloric1
International Hazard
Posts: 1140
Registered: 8-10-2003
Location: GroupVII of the periodic table
Member Is Offline
Mood: Stoichiometrically Balanced
|
|
ROSCO you are a scream!
Fellow molecular manipulator
|
|
Engager
Hazard to Others
Posts: 295
Registered: 8-1-2006
Location: Moscow, Russia
Member Is Offline
Mood: Lagrangian
|
|
Preparation of calcium cyanamide from urea and calcium carbonate.
[Edited on 8-3-2010 by Polverone]
|
|
SplendidAcylation
Hazard to Others
Posts: 203
Registered: 28-10-2018
Location: Starving in some deep mystery
Member Is Offline
Mood: No one I think is in my tree.
|
|
Write-up
Hi,
I have repeated the procedures detailed here, and I have had some success in the preparation of calcium cyanamide.
Moreover, I carried out a titration of my product, using the method proposed by Engager https://www.sciencemadness.org/talk/viewthread.php?tid=14267
Based on the results of the titration, my product had a purity of 53.9%.
I have detailed my whole procedure in a write-up that I have attached as PDF, I hope this will be helpful to anyone wishing to attempt this.
Attachment: Preparation of calcium cyanamide for SM.pdf (51kB) This file has been downloaded 350 times
|
|
clearly_not_atara
International Hazard
Posts: 2787
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
This would also lead to guanidine and possibly thiourea, methinks. The latter might be a little tricky.
Quote: | A convenient method for the preparation of secondary amines which are not contaminated with primary or tertiary amines is the reaction of cyanamide
with alkyl halides to N,N-dialkylcyanamides which can easily be hydrolyzed to dialkylamines and then decarboxylated. |
|
|
SplendidAcylation
Hazard to Others
Posts: 203
Registered: 28-10-2018
Location: Starving in some deep mystery
Member Is Offline
Mood: No one I think is in my tree.
|
|
Where would the sulphur come from?
Quote: Originally posted by clearly_not_atara | Quote: | A convenient method for the preparation of secondary amines which are not contaminated with primary or tertiary amines is the reaction of cyanamide
with alkyl halides to N,N-dialkylcyanamides which can easily be hydrolyzed to dialkylamines and then decarboxylated. |
|
Oh I see you got that from Wikipedia... Decarboxylation!? Lol. I guess someone will need to edit it and correct that...
[Edited on 29-3-2023 by SplendidAcylation]
|
|
clearly_not_atara
International Hazard
Posts: 2787
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Sulfur would have to come from hydrogen sulfide, or hopefully a synthon, e.g. NaSH.
Hydrolysis product of a dialkyl cyanamide is probably the carboxamic acid, which decarboxylates when protonated.
|
|
SplendidAcylation
Hazard to Others
Posts: 203
Registered: 28-10-2018
Location: Starving in some deep mystery
Member Is Offline
Mood: No one I think is in my tree.
|
|
Quote: Originally posted by clearly_not_atara | Sulfur would have to come from hydrogen sulfide, or hopefully a synthon, e.g. NaSH.
Hydrolysis product of a dialkyl cyanamide is probably the carboxamic acid, which decarboxylates when protonated. |
Not many people know this, but Neil Young left CSNY because he said Graham Nash smelled unbearable when anyone spilled acid on him.
Ahhh yes that makes sense.
Still, surely "hydrolyzed to dialkylamines and then decarboxylated" is incorrect, since a dialkylamine isn't a carboxamic acid?
True, it could be an amine and a carboxamic acid, of course, but to refer to it as an amine would be unhelpful, akin to referring to an amino acid as
an amine, am I correct or am I just too tired and talking nonsense?
|
|
night429
Harmless
Posts: 48
Registered: 12-11-2019
Member Is Offline
Mood:
|
|
I recently produced calcium cyanamide by this method (ammoniacal silver nitrate produced the characteristic yellow precipitate). Despite washing the
calcium cyanate with over 1L of water pre-calcination, I'm still concerned about the presence of sodium cyanide being present in the solid.
In adding the calcium cyanamide directly to a solution of ferrous sulfate, followed by acidifcation, only a yellow solution formed. Is this a good
enough test result to show cyanide is trace, if present at all?
In a free fall of fire and ice with explosions in the sky
|
|
clearly_not_atara
International Hazard
Posts: 2787
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Cyanide formation in this rxn is very unlikely because it would require carbon to be reduced, but there is no reducing agent present. Formally,
cyanate and cyanamide are both compounds of cyanyl, CN+, while cyanide is CN-.
|
|