Pupper
Harmless
Posts: 16
Registered: 14-11-2017
Location: STRAYA
Member Is Offline
Mood: No Mood
|
|
Heating Element for DIY Hotplate
Hello everyone
I'm trying to make myself a hotplate, but I don't know what to use for the heating element. I've thought of Peltier modules but they don't seem very
efficient. I've also considered heating elements but most of them are too big and expensive.
Should I make my own heating element using nichrome wire?
(Sorry if this has already been posted... I did do a search but didn't find anything)
|
|
|
violet sin
International Hazard
Posts: 1480
Registered: 2-9-2012
Location: Daydreaming of uraninite...
Member Is Offline
Mood: Good
|
|
The conventional hot plate I opened had nichrome wire ribbon (flattened wire) wound around a mica sheet, spring pressed against a ceramic top surface.
The wire wasn't large, ~1/16" wide. If you want to go coppycat.
Alternately, I see coffee maker machines with the warming plate below have an attractive shape element and Teflon coated surface to match. But
plastic alone will not do to support it. Maybe brass standoff lugs or even long screws to give it stilts. Mount it to a coffee can or something
else common. A dimmer switch or such to set degree of ON.
Some skills required in tinkering/soldering/fabricating. Others have also used a clothes iron clamped upside down to a desk, with heat facing up. If
you like bought as is and cheap, one from a thrift store can be super affordable.
Ok, hope that helps
|
|
|
Pupper
Harmless
Posts: 16
Registered: 14-11-2017
Location: STRAYA
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by violet sin  | The conventional hot plate I opened had nichrome wire ribbon (flattened wire) wound around a mica sheet, spring pressed against a ceramic top surface.
The wire wasn't large, ~1/16" wide. If you want to go coppycat.
Alternately, I see coffee maker machines with the warming plate below have an attractive shape element and Teflon coated surface to match. But
plastic alone will not do to support it. Maybe brass standoff lugs or even long screws to give it stilts. Mount it to a coffee can or something
else common. A dimmer switch or such to set degree of ON.
Some skills required in tinkering/soldering/fabricating. Others have also used a clothes iron clamped upside down to a desk, with heat facing up. If
you like bought as is and cheap, one from a thrift store can be super affordable.
Ok, hope that helps |
thanks c:
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
| Quote: Originally posted by Pupper | Hello everyone
I'm trying to make myself a hotplate, but I don't know what to use for the heating element. I've thought of Peltier modules but they don't seem very
efficient. I've also considered heating elements but most of them are too big and expensive.
Should I make my own heating element using nichrome wire?
(Sorry if this has already been posted... I did do a search but didn't find anything) |
I can not imagine a diy hotplate that can compete with a simple hotplate like this
https://www.ebay.co.uk/itm/1500W-ELECTRIC-SINGLE-HOB-HOT-PLA...
and if you are competent to bypass the internal thermostat and use an external controller such as this
https://www.ebay.co.uk/itm/2000W-AC-50-220V-25A-Adjustable-M...
then you will have a very useful hotplate.
P.S. here in UK, on eBay there are many used domestic electric cookers, hobs, ovens ...
usually working and priced to sell/dispose of, replaced by one in this season's colours 
- worth checking second hand first.
[Edited on 23-1-2018 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Pupper
Harmless
Posts: 16
Registered: 14-11-2017
Location: STRAYA
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Sulaiman | | Quote: Originally posted by Pupper | Hello everyone
I'm trying to make myself a hotplate, but I don't know what to use for the heating element. I've thought of Peltier modules but they don't seem very
efficient. I've also considered heating elements but most of them are too big and expensive.
Should I make my own heating element using nichrome wire?
(Sorry if this has already been posted... I did do a search but didn't find anything) |
I can not imagine a diy hotplate that can compete with a simple hotplate like this
https://www.ebay.co.uk/itm/1500W-ELECTRIC-SINGLE-HOB-HOT-PLA...
and if you are competent to bypass the internal thermostat and use an external controller such as this
https://www.ebay.co.uk/itm/2000W-AC-50-220V-25A-Adjustable-M...
then you will have a very useful hotplate.
P.S. here in UK, on eBay there are many used domestic electric cookers, hobs, ovens ...
usually working and priced to sell/dispose of, replaced by one in this season's colours
- worth checking second hand first.
[Edited on 23-1-2018 by Sulaiman] |
Unfortunately that hotplate doesn't post to Australia :'(
|
|
|
BaFuxa
Hazard to Self
Posts: 61
Registered: 18-9-2017
Location: Mars
Member Is Offline
Mood: Buzzing
|
|
Well I have been down that road a few months back. I experimented a lot with nichrome wires and a voltage regulator.
I just wasted my time. Nichrome is real bitch to work with. Trust me I had looked at every possible DIY design there is on this planet and I could not
get it to work properly. Then there is the problem of heat regulation and safety. Playing around with that type of voltage is dangerous. You should
just by one on ebay, they are cheap, safe and work really well.
The only thing I still consider making myself is a furnace.
[Edited on 4-2-2018 by BaFuxa]
Potential counts for nothing until realized.
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
I have a single element version of this: Kmart hotplate
Dirt cheap. For our US friends Kmart is a bit like walmart.
Don't try to build an element - its not an easy thing to do well.
The other option is to find an electrical wholesaler that sells spares for ovens and hobs, and buy a solid element there.
But I'd bet the Kmart option is cheaper.
For more accurate temperature control you can buy PID controllers quite cheap off Aliexpress.com.
[Edited on 4-2-2018 by Twospoons]
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
