NedsHead
Hazard to Others
Posts: 409
Registered: 9-12-2014
Location: South Australia
Member Is Offline
Mood: No Mood
|
|
Polishing scratches from a microscope lens?
Does anyone know if it is possible to polish away light scratches from a microscope eye piece, and what about the objective lens?
I have a 10x eye piece that came with a mic I purchased at a garage sale, the mic appears to be a former school microscope and this particular eye
piece has seen better days, if there is a chance it can be fixed by polishing, without making it any worse, I'll give it a try.
I was thinking of using Cerium oxide from a glass repair kit and a microfibre cloth, but maybe that will be to coarse?, http://www.ebay.com.au/itm/4-OZ-Glass-Polishing-Kit-Cerium-O...
What do you think?
[Edited on 13-10-2016 by NedsHead]
|
|
|
Harristotle
Hazard to Others
Posts: 138
Registered: 30-10-2011
Location: Tinkerville
Member Is Offline
Mood: I tink therefore I am
|
|
You could try it.
Often those lenses are coated with various layers, and trying to repolish means that you damage these.
Good luck!
|
|
|
Sulaiman
International Hazard
Posts: 3697
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
since none of the lens surfaces should be in focus, a good clean may be enough.
Polishing a lens would remove any multicoating and probably introduce abberations.
I guess that the cost of used eyepieces and objectives is less than the cost of setting yourself up as a lens grinder/polisher.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
CuReUS
National Hazard
Posts: 928
Registered: 9-9-2014
Member Is Offline
Mood: No Mood
|
|
maybe you could try rubbing it with a banana - https://www.youtube.com/watch?v=CS2NMeUBArs
|
|
|
zed
International Hazard
Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Polishing with Cerium Oxide? Sure why not try it?
Might mess up the lens, might not. Worth a try.
You are aware that when buffing with Cerium Oxide under friction, the surface of the lens actually flows a little bit, to fill in gaps? Kinda like
"low temperature" melting.
|
|
|
diddi
National Hazard
Posts: 723
Registered: 23-9-2014
Location: Victoria, Australia
Member Is Offline
Mood: Fluorescent
|
|
you can buy very fine diamond paste. it is used for gem stone faceting which I do. it is MUCH finer than cerium oxide and much better for this
purpose. you can buy cheap sets of various grades of grit quite cheaply as little kits. they range from about 200 grit to 100,000 grit
try say 3000 and 15000 for glass
Beginning construction of periodic table display
|
|
|
wg48
National Hazard
Posts: 821
Registered: 21-11-2015
Member Is Offline
Mood: No Mood
|
|
I suggest you clean the lens first.
If you still think repolishing is the way to go try it first on a spare piece glass or even better a lens. Perhaps scratch it first. You will need
to swot up on the process.
You will probably need to remove the lens which may be very difficult. Note carefully which way round they were so you can reassemble them correctly.
Unless your into it for the fun I would not attempt it.
|
|
|
nezza
Hazard to Others
Posts: 324
Registered: 17-4-2011
Location: UK
Member Is Offline
Mood: phosphorescent
|
|
Do not try to polish the scratches out. It will invariably impair the performance of the lens. Clean it with a lint free cloth or at worst an approved
cleaning fluid.
If you're not part of the solution, you're part of the precipitate.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
