Zandins
Harmless
Posts: 25
Registered: 18-6-2016
Member Is Offline
Mood: No Mood
|
|
The Diaphragm Chronicles
Greetings Sciencemadness community,
Introduction
During the last month, I have done quite a lot of tinkering on different chloro-alkali electrolysis setups. One of the main caveats in its
implementation can be the diaphragm, which separates the anolyte from the catholyte. I have gone through several different materials and would like to
share my findings and conclusions.
Chapter 0:The Cell
The electrolysis cell is an empty plastic ice-cream box. The diaphragm separates the container into 2 unequal partitions. The cathode component(where
NaOH is generated) is approx. 3 times larger than the anode component, to provide more room for the product and reduce the amount of
chlorine-saturated water(in case of diaphragm failure).
Chapter I:Filter Paper
A diaphragm can be made from filter paper. If no sheet of sufficient size is avaliable, cardboard can be substituted with, with a cut square holding
the filter paper of available size.
Pros: Cheap, readily available and easily workable, low resistance.
Cons:Fails quickly in hot or corrosive conditions.
Conclusion: The simplest option in case of mundane, noncaustic chemicals.
Chapter II:Glasswool
Using epoxy resin, a patch of glasswool can be glued in the container.
Pros:Cheap, easily available
Cons:Irritant, can be a pain to adhere to the cell body, tends to fail after ~12h of use at the point of most mechanical stress(slightly above
the bottom adhesive)
Conclusion:More reliable than filter paper, though still not stable enough for bulk purposes.
Chapter III:Asbestos
In those countries where it is available, asbestos mattings can be used as diaphragms. However, safety precautions have to be observed, as asbestos is
harmful to the lungs.
Pros:Inert, durable
Cons:Hard to acquire, toxic.
Conclusion:Asbestos can be used effectively, however, its limited availability decreases its usefulness.
Chapter IV:Battey plate pockets
In some lead-acid battery, each plate is contained in a "pocket",which prevents badly adhering paste from falling off and shorting between plates. I
don't know the material they are made of, but it is durable,as they are made to resist 35 % sulfuric acid. The diaphragm must be soaked thoroughly
before it starts conducting ions.
Pros:Durable, does not fail
Cons: Must destroy a car battery, must be soaked in electrolyte for at least 30 minutes to start conducting current.
Conclusion:The best option taken so far.
To be continued...
----
In a few days' time, I plan to test each material's electrical resistance as well as add some pictures of my setups. This data will gradually appear
in the thread. Meanwhile, what are your preferred materials? Feel free to add any I am unaware of.
Zandins
|
|
|
Sulaiman
International Hazard
Posts: 3695
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
for some primary cell voltaic cell experiments I have been using these
http://www.edulab.com/prod/daniel-cell-porous-pot-150x50mm
|
|
|
BromicAcid
International Hazard
Posts: 3246
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
As I recall I have seen people using Tyvek and Gortex to various efficacies. An unglazed ceramic pot was always the go-to in college but it's my
understanding that it severely limits the current of your cell.
|
|
|
Fulmen
International Hazard
Posts: 1716
Registered: 24-9-2005
Member Is Offline
Mood: Bored
|
|
Something like Tyvek sounds promising. It's made from polyethylene, so it should be fairly resistant to chemical attacks. If needed you should be able
to heat-weld it to a larger support structure.
We're not banging rocks together here. We know how to put a man back together.
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
I've used ceramic pots for cells before and they definitely work, but the real question is how do you seal the hole at the bottom? Everything I've
tried hasn't fared well in the harsh environment of the cell.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
If you have access to a kiln for ceramics you could slip cast ceramic tubes, closed one end. These could be made to any desired composition and wall
thickness.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
Zandins
Harmless
Posts: 25
Registered: 18-6-2016
Member Is Offline
Mood: No Mood
|
|
Pottery
I have heard many people dismissing pottery as having too high electrical resistance, is there any quantitative data to confirm it?
|
|
|
careysub
International Hazard
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
This study tested Tyvek and found it had very high resistivity:
http://journals.plos.org/plosone/article?id=10.1371/journal....
But it is cheap and readily available and otherwise attractive (chemically resistant, tough), so if anyone has a mind to do any testing give it a go.
Any opinion on whether reverse osmosis membranes might be suitable?
http://www.ebay.com/itm/Osmosis-Membrane-Only-/112022860681?...
[Edited on 2-8-2016 by careysub]
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
Reverse osmosis membrane theorically will be of no use since it is only permeable to water...thus not to ions except maybe the ones from water
autoprotolysis (H(+) or H3O(+) and OH(-)); and if this happens, then you will have dramatic pH change from one side to the other...very fast leading
to reverse migration of the H(+) and OH(-) ions to neutralize.
[Edited on 2-8-2016 by PHILOU Zrealone]
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
Sulaiman
International Hazard
Posts: 3695
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
MrHomeScientist
i have read but not verified that candle wax is a suitable sealant for 'flower pot' holes.
Daniell's original cell used ox gullet ....
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
Quote: Originally posted by Sulaiman  | MrHomeScientist
i have read but not verified that candle wax is a suitable sealant for 'flower pot' holes.
Daniell's original cell used ox gullet .... |
Should be OK because wax is alcanic in nature --> hydrophobic, impermeable like polyethylen but with a much lower melting point...so don't go too
high or it will soften, lose integrity and melt.
Otherwise use silicone alone or PolyEthylen or PolyPropylen and glue (or silicone as a glue).
[Edited on 2-8-2016 by PHILOU Zrealone]
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
Romain
Hazard to Self
Posts: 63
Registered: 23-12-2013
Member Is Offline
Mood: Crystallized
|
|
Very interested in this topic, I'm looking to make a chlor-alkali cell too. Regarding flower pots:
I can say that I used one in a permanganate cell (see last post in permanganate thread for details) and it worked pretty well (alkaline sodium
permanganate up to 0.4 M on the anode side and KOH 1M on the cathode side). The pot was left untouched after electrolysis so it should withstand the
caustic environment in a chlor-alkali cell without too much trouble. Definitely not expensive to replace in any case.
As far as the electrical resistance is concerned, it worked surprisingly well (at 5 V and room temp. for a 7 cm diameter pot, a current of 500 mA
could pass through the cell).
And regarding sealing the bottom of the flower pot:
- I used a rubber stopper for the permanganate cell and it worked well.
- I tried candle wax for a very quick chlor-alkali test and it seemed to work too. Note that the wax tends to wick up in the ceramic and block the
pores so you loose some conductive surface on the sides if you use too much wax and heat for too long. It may not be an issue with bigger pots.
|
|
|
careysub
International Hazard
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
You might also consider sodium silicate/ground vermiculite cement for sealing. It is usually used as a high temperature cement, but should be an inert
ceramic material when hardened.
On-line guidance also suggests: "Adding a small amount of Portland cement or plaster to an aggregate mix of sodium silicate and vermiculite will cause
the mixture to set in just a few minutes."
Although I know it is not typical for electrolysis cells to operate "hot", be aware that candle wax can start to melt around 120 F, and the widely
available GulfWax melts at 128-133 F. The silicate cement can take any temperature.
[Edited on 17-9-2016 by careysub]
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
All interesting options! I'll have to try those next time I make a cell.
I've tried various types of caulk but those all fail relatively quickly. Candle wax sounds quick and easy.
|
|
|
alive&kickin
Hazard to Others
Posts: 100
Registered: 10-11-2012
Member Is Offline
Mood: No Mood
|
|
MrHomeScientist & Zandins, no need to seal a hole in ceramic pots when you can find them without holes. Found these at Walmart, (also saw them at
Michael's craft store, I'm sure others carry them) for $3.00 and they hold approx 500ml. Of course the outside pot would have to be fairly large, but
should work.
[Edited on 21-9-2016 by alive&kickin]
|
|
|
Deathunter88
National Hazard
Posts: 519
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by alive&kickin | MrHomeScientist & Zandins, no need to seal a hole in ceramic pots when you can find them without holes. Found these at Walmart, (also saw them at
Michael's craft store, I'm sure others carry them) for $3.00 and they hold approx 500ml. Of course the outside pot would have to be fairly large, but
should work.
|
The glaze on the inside of the pot would pose a problem right?
|
|
|
alive&kickin
Hazard to Others
Posts: 100
Registered: 10-11-2012
Member Is Offline
Mood: No Mood
|
|
sorry Deathhunter88, wrong picture, picked up both at the store glazed and unglazed. Wasn't sure what I was going to use them for at the time, but
thought ought to grab them while I could.
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
Wow nice! In the gardening section? I will definitely get some of those.
|
|
|
careysub
International Hazard
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
| Quote: Originally posted by alive&kickin | MrHomeScientist & Zandins, no need to seal a hole in ceramic pots when you can find them without holes. Found these at Walmart, (also saw them at
Michael's craft store, I'm sure others carry them) for $3.00 and they hold approx 500ml. Of course the outside pot would have to be fairly large, but
should work.
[Edited on 21-9-2016 by alive&kickin] |
I wonder if these are a regional item. I have looked at both stores in the past and have never seen them (SoCal) and they do not appear on either
stores website from what I can tell. I know that not everything in these stores is a national item.
When searching on-line for ceramic electrolysis cells I have found the terms of art are "porous cup" and "porous pot" is you want to find purpose-made
ones. They are rather hard to source even so.
In the UK you have "porous pot" at http://education.scichem.com/
In the US "porous cup" here:
http://crscientific.com/electricity.html
http://products.unbeatablesale.com/ginsberg_scientific_7_182...
In India:
http://japson.com/product/porous-pot-_280_4.html
In Australia:
http://www.haines.com.au/index.php/lab-equipment/porous-pot-...
Ginsberg Scientific makes these for school use (and Googling "Ginsberg cup" or variations is useful), and are available cheap in quantity here:
http://www.teachersupplysource.com/product/64163/ginsberg-po...
Anyone want to do a group order? They are only $1.75, but the minimum order is $40 (they have other school supplies though, so you could piggy-back).
This same Ginsberg cup is available on Amazon for the preposterous price of $22 each:
https://www.amazon.com/Ginsberg-Porous-Cup-Voltaic-Cell/dp/B...
I think you can order these from Fischer since it runs an educational supply operation, and is not just a B2B outfit:
https://www.fishersci.com/shop/products//s13612
[Edited on 21-9-2016 by careysub]
|
|
|
yobbo II
National Hazard
Posts: 763
Registered: 28-3-2016
Member Is Offline
Mood: No Mood
|
|
The Nafion store
http://www.nafionstore.com/
Nafion tubes
http://www.permapure.com/products/nafion-tubing/
[Edited on 28-9-2016 by yobbo II]
|
|
|
careysub
International Hazard
Posts: 1339
Registered: 4-8-2014
Location: Coastal Sage Scrub Biome
Member Is Offline
Mood: Lowest quantum state
|
|
| Quote: |
The store at least lists prices and has an actual store front purchasing system in place. But the cheapest membrane listed is $140 per square foot.
Not impossibly expensive, just very, very expensive:
http://www.nafionstore.com/store/p/40-Nafion-Membrane-NR-211...
Like most industrial suppliers, there are no prices listed, nor any way to buy on-line. You have to contact them for a quote, and submit a purchase
order. Nearly all such places have no interest in dealing with hobbyists (I occasionally try to contact such places, but rarely do I get a response,
and never a helpful one thus far.) |
About that which we cannot speak, we must remain silent.
-Wittgenstein
Some things can never be spoken
Some things cannot be pronounced
That word does not exist in any language
It will never be uttered by a human mouth
- The Talking Heads
|
|
|
yobbo II
National Hazard
Posts: 763
Registered: 28-3-2016
Member Is Offline
Mood: No Mood
|
|
Agreed on all fronts.
One way to get some product that sometimes works is to request a sample. You can suggest you are a student or somesuch.
If two people were to purchase the square foot it would get more manageable but still expensive.
These guys sell smaller amounts but the price is the same for a square foot
http://fuelcellsetc.com/store/Nafion/N212?gclid=CPK19tfAtM8C...
Lots to choose from here but the prices are still high
http://fuelcellstore.com/fuel-cell-components/membranes
The 'resin' beads that (I don't know exactly what these things are) are in water softeners were obtained, places onto a flat surface (say a glass
sheet) in a one bead layer and they some substance (say polyester resin (no relation the the 'resin' mentioned above) or wax) was pored onto this
layer so that a sheet of 'resin beads in a solid matrix' was formed. This could be used as a membrane (or could it). The beads would perhaps be too
thick. What are the beads made from?
You sometimes see domestic water softeners dumped with the beads still inside.
http://www.softenerparts.com/Resin_Replacement_s/54.htm
Resin for sale
http://www.softenerparts.com/High_Capacity_Cation_Softening_...
About 120 dollars for a cubic foot of stuff. That would make a lot of one bead think membrane assuming the half crazy idea is sensible.
Water softening manual attached.
[Edited on 29-9-2016 by yobbo II]
Attachment: 0901b80380885879.pdf (2.8MB)
This file has been downloaded 550 times
|
|
|
Melgar
Anti-Spam Agent
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
Doesn't anyone else use glue guns to quickly assemble prototypes? The glue sticks that they use are basically low-melting-point polyethylene. At
least the white translucent ones are. And in my experience, as long as you attach it to a clean, dry surface, it has the same chemical properties as
polyethylene, in that it's inert to just about everything as long as it stays below its melting point, which is hot enough to burn your skin, so
probably 80-90C. You could just put the pot on an upside-down beaker or some other piece of glass, then use a glue gun to fill in the hole with glue,
or use any other heat source for that matter. Or just glue a piece of polyethylene to the top or the bottom of the hole.
edit: yobbo, you want ion exchange MEMBRANES, not resin.
[Edited on 9/30/16 by Melgar]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
