RogueRose
International Hazard
Posts: 1594
Registered: 16-6-2014
Member Is Offline
|
|
Sipohn flow rate
I've always been curious if there is something that governs the speed at which siphoning can occur. If a pump is used to start the process and a rate
of 30 GPM is achieved, will that rate be continued when the pump is removed (as long as the outlet is below the source)?
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by RogueRose | I've always been curious if there is something that governs the speed at which siphoning can occur. If a pump is used to start the process and a rate
of 30 GPM is achieved, will that rate be continued when the pump is removed (as long as the outlet is below the source)? |
You can find a more or less complete mathematical derivation of how siphons work, here:
http://www.sciencemadness.org/talk/viewthread.php?tid=65532&...
In short, once initial flow is established by a pump and you then switch off the pump, the initial rate becomes irrelevant very quickly. The flow rate
of a siphon isn't affected by the initial rate but is determined by gravity and limited by friction (viscous) resistance in the siphon's pipe itself.
So if initially a rate of 30 GPM was established by the pump, after switching off the pump, the volumetric flow rate Qv will
adjust until it is approx.:
$$Q_v \approx \frac{\pi}{4}D^2\sqrt{2gy}$$
With D the siphon pipe diameter and y the height difference between the surface of the water and the outlet of the siphon. The
formula is roughly valid for internally smooth siphons that aren't too long.
[Edited on 28-5-2016 by blogfast25]
|
|
Eddygp
National Hazard
Posts: 858
Registered: 31-3-2012
Location: University of York, UK
Member Is Offline
Mood: Organometallic
|
|
Oh wow! In spite of knowing that there have been many topics discussed here, I would have never thought that this would have been addressed already.
there may be bugs in gfind
[ˌɛdidʒiˈpiː] IPA pronunciation for my Username
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Quote: Originally posted by blogfast25 |
$$Q_v \approx \frac{\pi}{4}D^2\sqrt{2gy}$$
With D the siphon pipe diameter and y the height difference between the surface of the water and the outlet of the siphon. The
formula is roughly valid for internally smooth siphons that aren't too long.
|
I thought this equation looked familiar. It is Toricelli's law, equally valid for a tank draining through an orifice:
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Magpie | Quote: Originally posted by blogfast25 |
$$Q_v \approx \frac{\pi}{4}D^2\sqrt{2gy}$$
With D the siphon pipe diameter and y the height difference between the surface of the water and the outlet of the siphon. The
formula is roughly valid for internally smooth siphons that aren't too long.
|
I thought this equation looked familiar. It is Toricelli's law, equally valid for a tank draining through an orifice:
|
Yes, in the simple treatment of siphons the head loss in the pipe is neglected, which is OK for short, smooth siphons. Bear in mind though that for
siphons y is not the same as the fluid height in a tank.
Taking head loss into account makes it quite complicated, mathematically.
[Edited on 28-5-2016 by blogfast25]
|
|