| Pages:
1
2 |
killer_lapin
Harmless
Posts: 47
Registered: 23-7-2010
Location: Qc, CAN
Member Is Offline
Mood: No Mood
|
|
Arecoline extraction
Hi guy,
Few months ago I've extracted some arecoline from betel nuts. I just wanted to share it with you since I've used a common extraction technique which
can work with other compounds as well.
I grounded the dry nuts and puted them in 10% KOH and start an hydrodistillation.
<img src="https://24.media.tumblr.com/81327048997e6e9fa73b326710fe51b4/tumblr_mxnv60gKVW1t7vuido3_1280.jpg" width="800" />
I from the turbidity could clearly see that there was something in the distillate. After what I've extracted the distillate twice with ether and
setted up an HCl bubbler.
<img src="https://24.media.tumblr.com/5e3dcf180f5b74966f4e635512d31836/tumblr_mxnv60gKVW1t7vuido2_1280.jpg" width="800" />
Then there was this fine precipitation of the arecoline hydrochloride.
<img src="https://31.media.tumblr.com/b49f1e71128633321deea8c7d1081e46/tumblr_mxnv60gKVW1t7vuido1_1280.jpg" width="800" />
Sadly the hydrochloride crystals were to fine to get a nice powder after filtration, it all stayed on the cellulose filter.It still have some betel
nuts around and if you have idea to improve the process I may try it again. ( And sorry for the large pictures I'll do better next time I make a post)
<!-- bfesser_edit_tag -->[<a href="u2u.php?action=send&username=bfesser">bfesser</a>: reduced
image size(s)]
[Edited on 11.12.13 by bfesser]
|
|
|
Crowfjord
Hazard to Others
Posts: 390
Registered: 20-1-2013
Location: Pacific Northwest
Member Is Offline
Mood: Ever so slowly crystallizing...
|
|
Nice. It would be interesting to do a TLC on the freebase extract. I suspect there may also be a small amount of guvacoline (nor-arecoline I suppose
one could call it, the N-demethyl analog) present. I have also wondered to what extent dimers, oligimers and polymers would form from Michael reaction
between the areca alkaloids in an extraction like this.
|
|
|
killer_lapin
Harmless
Posts: 47
Registered: 23-7-2010
Location: Qc, CAN
Member Is Offline
Mood: No Mood
|
|
Good idea to do a TLC, I haven't tought of that! Most of the alkaloid of this plant wouldn't show with UV, but I'think I still have Iodine on silica
gel which would reaveal the arecoline and guvacoline.
|
|
|
Nicodem
Super Moderator
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
That does not make sense. How could a methyl ester survive such treatment? And what's the reference for this isolation?
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
|
killer_lapin
Harmless
Posts: 47
Registered: 23-7-2010
Location: Qc, CAN
Member Is Offline
Mood: No Mood
|
|
Methyl esters are quite resistant, usualy LiOH is used because it coordinate with the carbonyl and helps the hydrolysis.
The 10% KOH idea comes from The Alkaloïds Vol I-Chemistry and physiology. They used a much complex procedure, I've cutted corners because I've read
somewhere that it was steam volatile but the amine needs to be deprotonated.
But you may also be right wich would explain why I had so little product. Next time I could try with K2CO3 insted of KOH. I can put the actual
procedure if you want.
Edit: it was actally moisten with 10% KOH(from the alkaloids) then i added water to have a sufficient volume to steam distill.
[Edited on 13-12-2013 by killer_lapin]
|
|
|
Nicodem
Super Moderator
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
You are very wrong. Methyl ester, particularly the aliphatic ones, hydrolyze in mater of minutes to one hour in single phase 10% aq. KOH. You can be
sure that this is going to be very fast at 100 °C.
| Quote: | | The 10% KOH idea comes from The Alkaloïds Vol I-Chemistry and physiology. They used a much complex procedure, I've cutted corners because I've read
somewhere that it was steam volatile but the amine needs to be deprotonated. |
Yes, post the whole procedure. Also, in the future make sure you provide references even when you make adaptations to the published ones.
| Quote: | | But you may also be right wich would explain why I had so little product. Next time I could try with K2CO3 insted of KOH. I can put the actual
procedure if you want. |
You only need a buffer to maintain about neutral pH. You don't need a strong base. K2CO3 also readily hydrolyzes methyl esters
at the water boiling point. Try with NaHCO3 or Na2HPO4.
…there is a human touch of the cultist “believer” in every theorist that he must struggle against as being
unworthy of the scientist. Some of the greatest men of science have publicly repudiated a theory which earlier they hotly defended. In this lies their
scientific temper, not in the scientific defense of the theory. - Weston La Barre (Ghost Dance, 1972)
Read the The ScienceMadness Guidelines!
|
|
|
killer_lapin
Harmless
Posts: 47
Registered: 23-7-2010
Location: Qc, CAN
Member Is Offline
Mood: No Mood
|
|
Here is the actually extraction methode for arecoline. It's complexe so you can understand why I tried a simple hydrodistillation.
The ground areca nut (in 500-kg. lots) is moistened with 250 kg. of 10% aqueous
potassium hydroxide, dried and successively refluxed for 2 hours with three portions of
ether. The combined extract is concentrated to 80 L. and the water that separates is
removed. The concentrate is then divided into portions of convenient volume and to
each 50% acetic acid is added with stirring until a turbidity appears. After vigorous
stirring, water (1 L.) is added and the ether removed by distillation. After the last trace
of ether has been removed, the warm aqueous solution is allowed to cool overnight in
evaporating dishes. The solid fat which rises to the surface is collected, melted, and
stirred with several 1L. portions of water, each time allowing it to cool and decanting
the water to recover the base retained by the fat. The combined acidic aqueous extract
is filtered and extracted with ether to remove suspended and nonbasic material, then
saturated with potassium carbonate, shaken with three portions of ether, and dried over
anhydrous potassium carbonate. The mixture of bases, recovered after removal of the
ether, is sufficiently pure to be used directly for the isolation of pure arecoline as its
hydrobromide. The bases are dissolved in twice their weight of absolute ethanol, the
solution filtered, cooled, and made slightly acid by the addition, with stirring, of a 50%
ethanolic solution of hydrogen bromide. The crystalline hydrobromide separates on
the addition of ether to incipient turbidity followed by clarification with a few drops of
ethanol. The solution is cooled for 24 hours and the crystalline salt is filtered and washed
first with an ethanol-ether mixture, and then with ether. The arecoline hydrobromide
thus obtained, when dried at 60°, melts at 170°.
Edit: procedure from The Alkaloïds Vol I-Chemistry and physiology p.171
[Edited on 15-12-2013 by killer_lapin]
|
|
|
bfesser
Resident Wikipedian
Posts: 2114
Registered: 29-1-2008
Member Is Offline
Mood: No Mood
|
|
Please cite a reference when you copy-paste procedures and such.
|
|
|
Crowfjord
Hazard to Others
Posts: 390
Registered: 20-1-2013
Location: Pacific Northwest
Member Is Offline
Mood: Ever so slowly crystallizing...
|
|
It's interesting that they do it that way. I wonder why they handled the fat manually rather than acidifying and defatting with a solvent. If I was to
try the arecoline extraction (had I not found an established procedure), I would wet with acid, defat with naphtha or petroleum ether (or similar),
then basify and extract with a non-polar (like ether). After that, I like what they do in the above reference. Does anyone know if there is an
advantage to salting with HBr rather than HCl or other acid? I've noticed that commercial arecoline is usually sold as the hydrogen bromide salt.
There must be a reason.
|
|
|
DJF90
International Hazard
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
It could be that the hydrochloride salt is hygroscopic/deliquescent. There are many factors involved in salt selection, and even more if you're
considering pharmaceutical salts.
|
|
|
bfesser
Resident Wikipedian
Posts: 2114
Registered: 29-1-2008
Member Is Offline
Mood: No Mood
|
|
<a href="http://www.scribd.com/doc/35979437/The-Alkaloids-Chemistry-and-Physiology-Volume-1-1950#page=180" target="_blank">The Alkaloids -
Chemistry and Physiology - Volume 1 (1950)</a> <img src="../scipics/_ext.png" />
[Edited on 17.12.13 by bfesser]
|
|
|
BillyRubin
Harmless
Posts: 1
Registered: 21-12-2013
Member Is Offline
Mood: No Mood
|
|
FWIW: "A general procedure for extracting fresh plant tissues and fractionating into different classes according to polarity was described by Harborne
in 1998."
-illustrated in Phytochemical Techniques by N. Raaman, ISBN 81-89422-30-8
Many other detections and isolations are detailed also.
|
|
|
metalayer
Harmless
Posts: 23
Registered: 7-7-2013
Member Is Offline
Mood: No Mood
|
|
Calculating amount of solvent required
Is there a general method or equation for determining the quantity of a solvent (DCM in my case) needed to extract x moles of a compound?
Thanks
|
|
|
Mailinmypocket
International Hazard
Posts: 1351
Registered: 12-5-2011
Member Is Offline
Mood: No Mood
|
|
Research the solubility of said compound in DCM
|
|
|
metalayer
Harmless
Posts: 23
Registered: 7-7-2013
Member Is Offline
Mood: No Mood
|
|
I can't find the solubility anywhere. Compound in question is Arecoline Hydrobromide.
Is there a way to calculate its solubility in DCM if I know its solubility in another solvent like diethyl ether?
|
|
|
Pyro
International Hazard
Posts: 1305
Registered: 6-4-2012
Location: Gent, Belgium
Member Is Offline
Mood: No Mood
|
|
Not calculate, but you can speculate.
why not use ether?
If acquiring DCM isn't a problem, just use a large excess. Then just Distill/evaporate the DCM off
all above information is intellectual property of Pyro.  |
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
Take 10ml of DCM and put it in a beaker on top of your mag stirring hotplate. Take an accurate temperature measurement. Add a stirbar and begin
stirring. Slowly add your compound untill no more will dissolve at that temp. Then raise/ lower the temp, with fresh DCM and do it agian. Plot all
your data and make a solubility curve, then post it for the world to benefit.
[Edited on 10-1-2014 by Bot0nist]
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
metalayer
Harmless
Posts: 23
Registered: 7-7-2013
Member Is Offline
Mood: No Mood
|
|
Thanks for your responses, I'm on the right track now.
|
|
|
Pyro
International Hazard
Posts: 1305
Registered: 6-4-2012
Location: Gent, Belgium
Member Is Offline
Mood: No Mood
|
|
I assumed that since he wants to extract it he doesn't have any to test solubility
all above information is intellectual property of Pyro. |
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
I thought as much too, but he could perhaps do a small extraction with a large excess of DCM, or ether, then plot a solubility curve for DCM to do the
bulk of the extraction more efficiantly...
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Bot0nist  | Take 10ml of DCM and put it in a beaker on top of your mag stirring hotplate. Take an accurate temperature measurement. Add a stirbar and begin
stirring. Slowly add your compound untill no more will dissolve at that temp. Then raise/ lower the temp, with fresh DCM and do it agian. Plot all
your data and make a solubility curve, then post it for the world to benefit.
[Edited on 10-1-2014 by Bot0nist] |
Do you realise just how volatile DCM is? Without a refluxer you're likely to lose most of it to evaporation quite quickly, even more so if you're
going to heat it. The lowest setting on a hot plate is likely to cause it to boil!
[Edited on 11-1-2014 by blogfast25]
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
Sorry, that slipped my mind. Maybe follow chemikids advice and chill the glassware first. Use an icebath and start at 0°c and work up from there.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
Pyro
International Hazard
Posts: 1305
Registered: 6-4-2012
Location: Gent, Belgium
Member Is Offline
Mood: No Mood
|
|
reflux...
just use a condenser or a flask cooled with AN/Ice water, that is supposed to go as low as -30*C
all above information is intellectual property of Pyro. |
|
|
Mailinmypocket
International Hazard
Posts: 1351
Registered: 12-5-2011
Member Is Offline
Mood: No Mood
|
|
This might be helpful to you:
Attachment: Arecoline.pdf (100kB)
This file has been downloaded 895 times
|
|
|
metalayer
Harmless
Posts: 23
Registered: 7-7-2013
Member Is Offline
Mood: No Mood
|
|
Freebasing with NaOH
I am trying to follow a synthesis which involves making freebase Arecoline from Arecoline Hydrobromide. The synth suggests using sodium bicarbonate to
freebase, but I have found that creates horrible emulsions and makes extremely difficult to separate phases. Could I use NaOH instead?
Thanks
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
