| Pages:
1
2 |
Lithium
Hazard to Others
Posts: 103
Registered: 25-2-2012
Location: Australia
Member Is Offline
Mood: Thinking!
|
|
silver nitrate
hello
i want to sell silver nitrate, because i can buy and make all the chemicals relatively cheaply, and make a profit on it.
my only concern is if people will actually want to buy from me, and not a chem supplier giant. it will only be on ebay or amazon.
another problem is the quantity of calcium nitrate and sulfuric acid i would buy, would it raise some eyebrows?
Li
|
|
|
Hexavalent
International Hazard
Posts: 1564
Registered: 29-12-2011
Location: Wales, UK
Member Is Offline
Mood: Pericyclic
|
|
I know some people might be uncomfortable buying from a comparatively new member . . .consider using PayPal, and it will make people a lot more at
ease.
To sell the stuff, you will need to make sure that it is quite pure, to the grade that you sell it as or above. Look into recrystallizations or other
techniques.
Personally, my chemistry teacher has promised me a few grams of silver metal . . .you know the copper wire in AgNO3 experiment? He's done that 5 times
recently, he normally saves the precipitated silver, shows it to his class and then chucks it . . .this time, I'll be coming in with a labeled vial
on Monday
"Success is going from failure to failure without loss of enthusiasm." Winston Churchill
|
|
|
Lithium
Hazard to Others
Posts: 103
Registered: 25-2-2012
Location: Australia
Member Is Offline
Mood: Thinking!
|
|
yes, i know how to recrystalize
i would sell it on ebay, which i think has paypal as a payment selection.
is it legal in aus to buy lots of nitrates and H2SO4, i suppose it should be fine if i buy silver bullion with it
Li
|
|
|
Endimion17
International Hazard
Posts: 1468
Registered: 17-7-2011
Location: shores of a solar sea
Member Is Offline
Mood: speeding through time at the rate of 1 second per second
|
|
Quote: Originally posted by Hexavalent  | I know some people might be uncomfortable buying from a comparatively new member . . .consider using PayPal, and it will make people a lot more at
ease.
To sell the stuff, you will need to make sure that it is quite pure, to the grade that you sell it as or above. Look into recrystallizations or other
techniques.
Personally, my chemistry teacher has promised me a few grams of silver metal . . .you know the copper wire in AgNO3 experiment? He's done that 5 times
recently, he normally saves the precipitated silver, shows it to his class and then chucks it . . .this time, I'll be coming in with a labeled vial
on Monday
|
He THROWS AWAY silver?! 
|
|
|
barley81
Hazard to Others
Posts: 481
Registered: 9-5-2011
Member Is Offline
Mood: No Mood
|
|
Sadly, most high school chem teachers do. The other day, the chemistry club at my school tried to make silver mirrors (one person dropped their test
tube and we had to abort). I tried to save the silver but the teacher wouldn't let me. She threw it out. Aargh.
That teacher is too much. It's her second year at my school, and she teaches both the advanced (senior) and the regular chemistry courses. She asked
me why sugar was a reducing agent during an experiment 
|
|
|
Endimion17
International Hazard
Posts: 1468
Registered: 17-7-2011
Location: shores of a solar sea
Member Is Offline
Mood: speeding through time at the rate of 1 second per second
|
|
Even the lab manuals dictate that precious metals should be collected and appropriately precipitated.
Throwing the silver away is one of the most stupid things to do, and it costs the school a lot of money. Silver nitrate is expensive, and it's one of
the easiest things to recycle.
I understand they throw silver mirrored tubes away (the amount inside is way too small), but precipitated silver tree from a copper wire contains a
lot more. Throwing that away is just ridiculous. I'd tell the teacher that he/she is making unneccessary costs to the school budget.
|
|
|
barley81
Hazard to Others
Posts: 481
Registered: 9-5-2011
Member Is Offline
Mood: No Mood
|
|
No, it wasn't the tubes she threw away, but the silvering solution. There was a fair amount of silver oxide precipitate after dilution.
|
|
|
neptunium
National Hazard
Posts: 989
Registered: 12-12-2011
Location: between Uranium and Plutonium
Member Is Offline
|
|
dont sale your stuff on ebay ! ebay is great for a buyer but your product will end up on the business and industrial section and you'll be taxed 9% on
every sale!!!!!!!!
I dont know how big time seller do it on there but every time i had some to sale i got f."@/d hard!!
|
|
|
Lithium
Hazard to Others
Posts: 103
Registered: 25-2-2012
Location: Australia
Member Is Offline
Mood: Thinking!
|
|
well, i am giving up on the idea of selling silver nitrate, but i still want to make some
i will probably think otherwise when it is the school holidays
can you react silver with liquid sulfur and dissolve that in HNO3 ( i have a use for H2S )
i have found about eight australian sixpence from 1941, which are apparently sterling silver. my grandma also broke two of her silver rings. all up i
have about 35g silver. i have saved up 5 old phones, and an iphone that doesn't work, how do i refine them?
Li
|
|
|
barley81
Hazard to Others
Posts: 481
Registered: 9-5-2011
Member Is Offline
Mood: No Mood
|
|
Don't bother with the sulfur and silver. Just dissolve the silver in the nitric acid to minimize contamination. To make hydrogen sulfide, just heat
some paraffin wax and sulfur together. You get carbon and H<sub>2</sub>S.
There are a few threads around here about refining sterling silver. IIRC, you can fuse the silver nitrate and decompose the copper nitrate into copper
oxide, and filter that off once you dissolve it in water.
|
|
|
BILLBUILDS
Hazard to Self
Posts: 82
Registered: 19-3-2016
Member Is Offline
Mood: No Mood
|
|
whats the method of making AgNO3? i have a few kg's of family silver which has no use anymore (people that it was important to are all dead)
|
|
|
ninhydric1
Hazard to Others
Posts: 345
Registered: 21-4-2017
Location: Western US
Member Is Offline
Mood: Bleached
|
|
Silver and nitric acid. And please UTFSE. There are too many threads on AgNO3 synthesis.
|
|
|
clearly_not_atara
International Hazard
Posts: 2786
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
IMO better to make the methanesulfonate which can be made with MeSO3H/H2O2 and which generates no toxic gases upon decomposition. Ethanesulfonate may
have comparable solubility.
https://www.alfa.com/en/catalog/018641/
|
|
|
Melgar
Anti-Spam Agent
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
First off, silver is only like $1/gram. That's not super cheap, true, but a 99.9% silver dollar typically costs like $30. It's not really that
expensive.
If you want to sell a chemical on eBay that you can make quite a lot on, go for PdCl2. It's a precious metal salt, so nobody expects it to be cheap,
however you can sell it for more than the palladium spot price, even though it's 60% chlorine by mass. To make it, just drop $800 or so on an ounce
of palladium (anything less rarely gets you close to the spot price), dissolve in aqua regia, then evaporate.
Anyone know of a decent way to refine silver chloride? Everyone seems to think it's a pain in the ass, but couldn't you just heat it red hot with
sugar or something?
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Online
Mood: No Mood
|
|
AgCl will give silver if you melt it with Na2CO3
|
|
|
clearly_not_atara
International Hazard
Posts: 2786
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Melgar - PdCl2 is a crucial component of a certain reaction used in the synthesis of a certain compound with a very high profit margin. As such it may
be important to have one's legal ducks in a row before selling PdCl2 to strangers online. I don't know why the demand exists but I know people
(blogfast) have gotten popped for selling less interesting stuff to less interesting people.
I'm pretty sure AgCl dissolves in concentrated hydrochloric acid; that solution can probably be easily reduced.
[Edited on 26-8-2017 by clearly_not_atara]
|
|
|
Melgar
Anti-Spam Agent
Posts: 2004
Registered: 23-2-2010
Location: Connecticut
Member Is Offline
Mood: Estrified
|
|
| Quote: Originally posted by clearly_not_atara | | Melgar - PdCl2 is a crucial component of a certain reaction used in the synthesis of a certain compound with a very high profit margin. As such it may
be important to have one's legal ducks in a row before selling PdCl2 to strangers online. I don't know why the demand exists but I know people
(blogfast) have gotten popped for selling less interesting stuff to less interesting people. |
Wacker oxidation of safrole? Yeah, I know, but as long as you're not advertising that as its purpose, it's not a controlled or restricted chemical in
any way. Maybe slightly suspicious, but it's also the most commonly used palladium salt for every other purpose that you'd have. However, the demand
on eBay is certainly fueled by the demand for the reductively aminated product of this reaction, I'm sure we can agree.
The first step in the process of learning something is admitting that you don't know it already.
I'm givin' the spam shields max power at full warp, but they just dinna have the power! We're gonna have to evacuate to new forum software!
|
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
I read (and attempted) in some old texts that AgClO3 can be prepared from the action of chlorine (aq) on a say silver oxide (or silver carbonate).
Soon after preparation, add Ag2O to stabilize the AgClO3 product.
After you have perfected that path along with the recycling of AgCl to silver, add cheap available KNO3:
AgClO3 + KNO3 = AgNO3 + KClO3
and you have two good salts.
--------------------------------------
Sources: To quote from "A comprehensive treatise on inorganic and theoretical chemistry", Volume 2, by Joseph William Mellor, page 271:
"L. N. Vauquelin found that when chlorine acts on silver oxide diffused in water, a mixture of silver chloride and chlorate is formed, and it was
accordingly supposed that these same products are obtained when chlorine acts on the salts of silver. The products observed by L. N. Vauquelin were
shown by A. J. Balard to be end products, being preceded by the formation of silver hypochlorite. According to A. J. Balard, finely divided silver
immediately decomposes hypochlorous acid with the evolution of oxygen, and the formation of silver chloride. Again, if an alkali hypochlorite be
treated with silver nitrate, or if silver oxide, Ag20, suspended in water, be treated with chlorine, much heat is developed and silver chloride and
silver peroxide are precipitated while a liquid with bleaching properties is formed. The liquid is very unstable, and decomposes in a few minutes with
the separation of silver chloride and the formation of a soln. of silver chlorate which does not bleach. If an excess of chlorine be employed, all the
silver is precipitated and a soln. of hypochlorous and chloric acids remains. If an alkali hydroxide be added to the bleaching liquid, oxygen is
evolved, and a mixture of silver chloride and peroxide is precipitated. Similar results are obtained if an aq. soln. of silver chlorate, nitrate, or
acetate be employed except that the corresponding acid is liberated. J. S. Stas has •shown that probably no chloric acid or silver chlorate is
formed in the primary reaction:
Ag20+2Cl2+H20=2AgCl+2HCl0
If the silver oxide or carbonate be in excess, the silver oxide gradually forms silver hypochlorite,
2HOCl + Ag20 =2AgOCl+H20
which is readily soluble, and the soln. is stable so long as it is shaken with the excess of silver oxide present. This salt is partially decomposed
on standing in darkness, and completely decomposed at 60° into silver chloride and chlorate:
3AgOCl=2AgCl+AgCl03
and the latter remains in soln. in the alkaline liquid. J. S. Stas found no signs of the formation of perchloric acid. F. Raschig prepared silver
hypochlorite by the action of alkaline sodium hypochlorite on silver nitrate, and also by adding a soln. of silver nitrate to sodium azide, NaN3, or
to a soln. of chloroazide in sodium hydroxide."
Link: https://books.google.com/books?pg=PA271&lpg=PA271&dq...
So the formation of Silver Chlorate is apparently not slow and one can actually visibly observe the formation of the AgCl. I suspect that AgClO3
should be quickly be employed in a reaction, or dried per the directions, as the aqueous solution is most likely not stable. In fact, Mellor (cited
previously), page 340, notes that AgClO3 decomposes into AgCl and O2 in the presence of HCl, HNO3 and even Acetic acid. Chlorine also reacts forming
AgCl, HClO3 and O2.
Also per another source "The principles of chemistry", Volume 2, by Dmitrïi Ivanovich Mendelieev, the bottom of page 403, to quote:
"This is how he describes the phenomenon which then takes place: if silver oxide or carbonate be suspended in water, and an excess of water saturated
with chlorine be added, then all the silver is converted into chloride, just as is the case with oxide or carbonate of mercury, and the water then
contains, besides the excess of chlorine, only pure hypochlorous acid without the least trace of chloric or chlorous acid. If a stream of chlorine be
passed into water containing an excess of silver oxide or silver carbonate, while the liquid is continually shaken, then the reaction is the same as
the preceding; silver chloride and hypochlorous acid are formed. But this acid does not long remain in a free state; it gradually acts on the silver
oxide and gives silver hypochlorite. If, after some time, the current of chlorine is stopped but the shaking is continued, then the liquid loses its
characteristic odour of hypochlorous acid, while preserving its energetic decolorising property, because the silver hypochlorite which is formed is
easily soluble in water. In the presence of an excess of silver oxide this salt can be kept for several days without decomposition, but it is
exceedingly unstable when there is not an excess of silver oxide or carbonate present. So long as the solution of silver hypochlorite is shaken up
with the silver oxide, it preserves its transparency and bleaching property, but directly it is allowed to stand, and the silver oxide settles, it
becomes rapidly cloudy and deposits large flakes of silver chloride, so that the black silver oxide which hud settled becomes covered with the white
precipitate. The liquid then loses its bleaching properties, and contains silver chlorato iu solution,...."
And from the bottom of page 404:
" In this manner the reactions whiih are consecutively accomplished may be expressed by the equations:
6Cl2 + 3Ag2O + 3H2O = 6AgCl + 6HCl0; 6HCl0 + 8Ag20 = 3 H20 + 6AgCIO;
6AgClO = 4AgCl + 2AgCl03.
Hence, Slas gives the following method for the preparation of silver chlorate. A slow current of chlorine is caused to act on oxide of silver,
suspended in water, which is put into a state of continuous movement. The shaking is continued after the supply of chlorine has been stopped, in order
that the free hypochlorous acid should pass into silver hypochlorite, and the resultant solution of the hypochlorite is drawn off from the sediment of
the excess of silver oxide. This solution decomposes spontaneously into silver chloride and chlorate. The pure silver chlorate, AgClO3, does not
change under the action of light. The salt is made ready for further use by drying it in dry air at 150°. It is necessary during drying to prevent
the access of any organic matter; this is done by filtering the air through cotton wool, and passing it over a layer of red-hot copper oxide."
Link: https://books.google.com/books?pg=PA403&lpg=PA403&dq...
So either the presence of free Chlorine in the bleach (which effectively lows the pH by forming HCl and also HOCl), or by the direct addition of a
weak acid (like CO2 or vinegar) forming HOCl, which reacts directly with Ag2O or AgCO3 to create the highly unstable silver hypochlorite. Then, AgClO
quickly disproportionates into AgCl and AgClO3 unless there is an excess of Ag2O or AgCO3 to promote the stability of the Silver hypochlorite.
I had added NaClO to Silver acetate dissolved in Acetic acid. The bleach and weak acid formed HOCl, which then reacted with Silver acetate to form a
white precipitate of AgCl. The solution also bubbled for a few weeks (O2 from the decomposition of AgClO3). Not the recommended path as acetic acid
will decompose AgClO3 on standing.
Note, only 1/3 of the Silver metal is converted into AgClO3, so , without recycling, this is an expensive route, but you may have some Silver
literally laying around. However, the above action path with KNO3 does introduce another salt of interest into the product mix.
Ag2CO3 can be prepared, for example, by adding silver to a solution of vinegar, H2O2 and a touch of KNO3 (acting as an electrolyte for this
electrochemical path). Jump start in a microwave. At completion, add Na2CO3 to create a Ag2CO3 precipitate which is isolated and washed.
[Edited on 7-10-2017 by AJKOER]
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Lithium
I hope that this is not too late, I just read this thread,
Based on very limited experience,
if you make silver nitrate from a 99.9% silver dollar, the remaining 0.1% (mainly copper I suspect)
is enough to make it less than ideal for photochemistry experiments, and long term storage.
I suggest a 99.99% Canadian Maple.
or
If you are confident of the purity of your nitric acid, use a 99.999% silver Canadian Maple for a really good product.
I am not confident of the impurity levels in my nitric acid so have not tried - speculation only.
EDIT: I guess that most members here, like me, would have difficulty assaying to 0.1%, and I don't know off-hand how I would even attempt a 0.01%
assay.
[Edited on 7-10-2017 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Online
Mood: No Mood
|
|
| Quote: Originally posted by Sulaiman | I hope that this is not too late, I just read this thread,
Based on very limited experience,
if you make silver nitrate from a 99.9% silver dollar, the remaining 0.1% (mainly copper I suspect)
is enough to make it less than ideal for photochemistry experiments, and long term storage.
I suggest a 99.99% Canadian Maple.
or
If you are confident of the purity of your nitric acid, use a 99.999% silver Canadian Maple for a really good product.
I am not confident of the impurity levels in my nitric acid so have not tried - speculation only.
EDIT: I guess that most members here, like me, would have difficulty assaying to 0.1%, and I don't know off-hand how I would even attempt a 0.01%
assay.
[Edited on 7-10-2017 by Sulaiman] |
At that level, you generally don't.
You measure all the credible impurities, for example, copper, sodium and iron, then calculate the purity of the silver salt as (100- the sum of all
the otehr stuff).
Typically you only measure metals and then report the purity as something like ">99.99% metals basis".
So you can get stuff labelled as 99.99% pure but which contains 5% water.
:-(
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
So for my silver nitrate that I made from a 99.9% silver American Eagle, which has a very faint blue/green tint,
how would I measure the (assume c0.1% copper) impurity content ?
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Metacelsus
International Hazard
Posts: 2539
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
AES would be the "gold standard" so to speak, but I doubt you have the equipment for that.
|
|
|
clearly_not_atara
International Hazard
Posts: 2786
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
Why would copper be so problematic in silver nitrate? Sigma sells it at 99% purity so I'm not sure what all this 99.99% stuff is about.
If you want to be rid of copper, you can precipitate silver as the acetate, and then pyrolyse this to the oxide and redissolve in HNO3 or just
dissolve AgOAc in HNO3 and boil away acetic acid (hopefully without catching fire). That's a lot of work though... and no it won't give you a copper
assay (but practically all metal acetates except silver will remain dissolved).
To observe the presence of copper, maybe add some of the (not acidic) nitrate solution to an excess of iodide salt -- Ag+ will precipitate as AgI
whereas Cu2+ will oxidize I- to I2 and precipitate as CuI. The resulting I2 should give an obvious brown coloration to the solution (as triiodide).
|
|
|
Fleaker
International Hazard
Posts: 1252
Registered: 19-6-2005
Member Is Offline
Mood: nucleophilic
|
|
| Quote: Originally posted by clearly_not_atara | Why would copper be so problematic in silver nitrate? Sigma sells it at 99% purity so I'm not sure what all this 99.99% stuff is about.
If you want to be rid of copper, you can precipitate silver as the acetate, and then pyrolyse this to the oxide and redissolve in HNO3 or just
dissolve AgOAc in HNO3 and boil away acetic acid (hopefully without catching fire). That's a lot of work though... and no it won't give you a copper
assay (but practically all metal acetates except silver will remain dissolved).
To observe the presence of copper, maybe add some of the (not acidic) nitrate solution to an excess of iodide salt -- Ag+ will precipitate as AgI
whereas Cu2+ will oxidize I- to I2 and precipitate as CuI. The resulting I2 should give an obvious brown coloration to the solution (as triiodide).
|
Or if you want to skip all that, just melt the silver nitrate, hold for 30 min at just over its melting point, and then dissolve up the silver nitrate
and filter the solution free of other oxides. Melting silver nitrate is still an effective way of purifying it. Sodium formate is another method,
wherein the first (things like Pd and Pt that co-dissolves with silver) and last fractions (Cu/Ni dragdown) are discarded for recycling and the middle
fraction is very high quality silver.
Analysis of silver can be done via Volhard's method. Used to do quite a few of those titrations by hand--I'd use XRF to analyze an unknown sample and
get a ballpark Ag %, then add titrant gravimetrically and use a microburette to finish it off. The titrant I would use (0.05N KSCN) was standardized
against 5N+ proof silver. Using this method, I could reliably tell 99.5% from 99.95%. With a potentiometric autotitrator, the method is off by about
$60 on every 100,000 in silver at $20/tr oz Ag. I still consider it the best/cheapest method of silver analysis despite owning an ICP-OES.
In any event, silver nitrate is stupid cheap--at industrial scale, there's a negligible premium to be had, maybe $0.30/50 grams. The old Kodak plant,
now Rochester Silver Works, is probably the largest producer in the world. A very impressive operation. Their silver nitrate of trade is 5N on a
metals basis with less than 0.1% moisture.
[Edited on 11-10-2017 by Fleaker]
Neither flask nor beaker.
"Kid, you don't even know just what you don't know. "
--The Dark Lord Sauron
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
That's a really interesting way to purify silver nitrate; I hadn't heard of that before. Wikipedia claims:
"Silver nitrate decomposes when heated:
2 AgNO<sub>3</sub>(l) → 2 Ag(s) + O<sub>2</sub>(g) + 2 NO<sub>2</sub>(g)
Qualitatively, decomposition is negligible below the melting point, but becomes appreciable around 250 °C and totally decompose at 440 °C."
citing http://aip.scitation.org/doi/10.1063/1.3253104 as its source.
So that means it's important to keep it right at the melting point, as you said. Neat!
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
