Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
Author: Subject: What are splash heads for?
JibbyDee
Harmless
*




Posts: 38
Registered: 25-11-2011
Member Is Offline

Mood: No Mood

[*] posted on 4-12-2011 at 09:44
What are splash heads for?


I came across these things called "splash heads" that look like this:


but I can't find any info explaining what they're for. The only info I found says that they are used for distillations in which the condenser is held vertically. I don't get it. Do they mean a reflux setup in which theres a splash head instead of a drying tube at the top of the condenser? In other words you heat the mixture, the vapours go up the condenser and the heavier vapours will be condensed and fall back into the flask while the lighter vapours will reach this splash head. What does the splash head do though?

[Edited on 4-12-2011 by JibbyDee]
View user's profile View All Posts By User
Sublimatus
Hazard to Others
***




Posts: 108
Registered: 8-6-2011
Member Is Offline

Mood: No Mood

[*] posted on 4-12-2011 at 10:47


My best guess is that it guards against bumping liquid from flying up and out of the vertical condenser.

They make something similar for rotavaps that protects against bumping solvent flying out of the flask and into the condensing chamber.

View user's profile View All Posts By User
zoombafu
Hazard to Others
***




Posts: 255
Registered: 21-11-2011
Location: U.S.
Member Is Offline

Mood: sciencey

[*] posted on 4-12-2011 at 13:05


They are just used as an anti-bumping measure, to make sure that your distilled product doesn't get contaminated.



View user's profile Visit user's homepage View All Posts By User
entropy51
Gone, but not forgotten
*****




Posts: 1612
Registered: 30-5-2009
Member Is Offline

Mood: Fissile

[*] posted on 4-12-2011 at 15:27


Old guys like me know these as "Kjeldahl Bulbs". See http://en.wikipedia.org/wiki/Kjeldahl_method In the Kjeldahl nitrogen analysis a sample (often a protein) is digested with acid to convert nitrogen to ammonium salt. This is then made basic with NaOH and the NH3 is distilled into standardized acid and titrated, thus allowing calculation of the amount of nitrogen in the sample. During the distillation the Kjeldahl bulb prevents an aerosol of NaOH from being carried over into the acid absorber and giving a falsely high nitrogen content.

Prevention of bumping being carried over is obviously another use for these.
View user's profile View All Posts By User
UnintentionalChaos
International Hazard
*****




Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline

Mood: Nucleophilic

[*] posted on 4-12-2011 at 15:53


I believe that the one in OP's post is specifically for kjeldahl nitrogen determination.



Department of Redundancy Department - Now with paperwork!

'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
View user's profile View All Posts By User
peach
Bon Vivant
*****




Posts: 1428
Registered: 14-11-2008
Member Is Offline

Mood: No Mood

[*] posted on 14-12-2011 at 10:29


Steam and other bumpy distillations; e.g. damp oily liquids or under vacuum (rotovaps).

{edit} "What does the splash head do though?" If you haven't run too many distillations before, you might not have encountered bumping, which is when the liquid tends to sit still not boiling, despite being at or over it's BP, and then suddenly boils in a fluster, throwing the contents upwards and towards the still head or receiver. The heads are designed to slow down or stop the passage of liquid phases (bumping) and only allow the vapour through. In a steam distillation, where you might want one of these, you also want two things (with different boiling points) to go through at the same time. So a simple distillation, as opposed to fractional, is needed. A head like this goes on the flask and then a condenser on the other end. {edit}

You can help limit bumping by drying things boiling over 100C prior to distillation, using stir bars or boiling stones (powdered glass), using a half or less full boiling flask, having a column in place (although it won't work so well as a fractioning column if there is persistent bumping), increasing the heat gently (not straight to full) and decreasing the pressure gently. If the thing in question is volatile and boils below 100C, it almost certainly wants cooling down prior to applying any vacuum; or it'll be effectively superheated at the reduced pressure and flash boil (as per dumping instant coffee into freshly microwaved water, or water into a pan of hot oil; it spits all the hot oil back at you as the water boils off).

Drying things can also help you get cleaner fractioning by eliminating the water that might blur the band between solvents and the higher boiling products.



[Edited on 15-12-2011 by peach]




View user's profile View All Posts By User
Paddywhacker
Hazard to Others
***




Posts: 478
Registered: 28-2-2009
Member Is Offline

Mood: No Mood

[*] posted on 15-12-2011 at 20:40


Naa... it's a bong.
View user's profile View All Posts By User
stoichiometric_steve
National Hazard
****




Posts: 827
Registered: 14-12-2005
Member Is Offline

Mood: satyric

[*] posted on 18-12-2011 at 15:30


now, that is a ridiculously big bump guard.




View user's profile View All Posts By User
hissingnoise
International Hazard
*****




Posts: 3940
Registered: 26-12-2002
Member Is Offline

Mood: Pulverulescent!

[*] posted on 18-12-2011 at 15:44


It's the picture --- waaay too big!


View user's profile View All Posts By User

  Go To Top