Organikum
resurrected
Posts: 2339
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
Steam Generator for Steamdistillations
So I am getting tired of rigging up the setup for steamdistillations with external steam source and directly from the flask takes often forever or
needs sophisticated precautions against foamig or splashing.
As steam-cans the traditional copper devices only exist anymore in universities to hassle students and the are a tidy bit antiquated I searched for a
modern option.
First option is a wallpaper remover. It was recommended by somebody on another board and told to work well. This one has a 4 liter tank 2000W and
makes about 58 g of steam per minute at a pressure < 2 bar.
https://www.ebay.de/itm/373319960425
I then looked further and found this "Steam cleaner" which is about the same power rating, makes 50 g of steam per minute when on "continous" setting
and does so at 3,5 bar pressure. It has only 1,5 liter water but can be refilled whilst running.
https://www.ebay.de/itm/374186602077
And then the Chinese monster, with 3000W, up to 115°C steam-temperature and 300-350 kPa (3 to 3,5 bar). The water throughput is said to be an
whopping 200 to 500 ml per minute, it can be regulated and the water comes by tube from a separate bucket, whats nice the pump is self-priming and
sucks up to 2 m so thats just fine. The smaller version of this has a named time limit for use of 30 minutes, I could not find anything regarding this
for the big boy.
https://www.ebay.de/itm/175357598518?
Has anybody used one of these, in the lab or anywhere, and has some experiences to share? Or maybe somebody knows something even better and cheaper
what I overlooked?
I contemplated to build something myself, but looking at the prices and the heap of unfinished projects calling my name thats just not economical, and
so this is pretty much out of question.
/ORG
|
|
Mush
National Hazard
Posts: 633
Registered: 27-12-2008
Member Is Offline
Mood: No Mood
|
|
4 stage mono tube boiler build High output
https://www.youtube.com/watch?v=7yw3AvSheEE
Or maybe this:
https://www.youtube.com/watch?v=AVxgUmP2XdE
Handheld steam cleaner Degreaser DIY
https://www.youtube.com/watch?v=yxlZRIour2Q
Simple construction, badass device.
"Chinese monster"
https://www.youtube.com/shorts/1oCmQSKQTl0
https://www.youtube.com/watch?v=zv93KH7JOGQ
https://www.aliexpress.com/item/32825303438.html?spm=a2g0o.p...
[Edited on 25-7-2022 by Mush]
|
|
Mateo_swe
National Hazard
Posts: 548
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
I read some use a pressure coocker as the steam source for distillations.
A used one is cheap at a second hand store and i think they work pretty well as a steam source.
|
|
Fantasma4500
International Hazard
Posts: 1681
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
"Handheld steam cleaner Degreaser DIY" is a very cool design, i wager with a descending spiral design one would need much less windings
i believe its coiled by filling the copper tube with sand so that it doesnt deflate when bending
seemingly its doable to weld copper using a spotwelder, i made my own so thats very doable
TIG welding is not easy, silver is more typically used for joining copper, zinc brazing is also a thing, seems he used some kind of brass brazing
technique
if you must, i'd assume just plugging maximum size of heating element into power socket and then having that coiled around something like concrete in
a closed container, then adding water to that, could also work well, i believe in europe its about 10 amps we can pull from the socket times 240
volts? 2400w. heating elements can be bought rather cheap on ebay, i bought like 10 pieces because they were so cheap
yes- i totally digressed OP's wish for wanting to just buy the finished piece, but i dont think it would be that tricky to get to work, especially not
if you use a rubber plug to stopper the hole where you put in water
|
|