denatured
Hazard to Others
Posts: 151
Registered: 7-8-2004
Location: -
Member Is Offline
Mood: HCl 50%?
|
|
Stainless steel in microwave oven
From what I read around it seems like almost everyone agrees on not putting metals in a microwave oven. but what if stainless steel is the only
material suitable for the reaction and you want to use microwave heating? what would you do?
|
|
Satan
Hazard to Others
Posts: 126
Registered: 1-5-2009
Member Is Offline
Mood: No Mood
|
|
Give more details. Like what you are going to make, and why stainless...
|
|
turd
National Hazard
Posts: 800
Registered: 5-3-2006
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by denatured | but what if stainless steel is the only material suitable for the reaction and you want to use microwave heating? |
Curious. Which reaction works only in highly reactive steel and not say in high-T annealed corundum (or ZrO or MgO)? These materials take some
beating. Have you checked for alternative crucible materials in Brauer's? There must be an alternative to steel.
|
|
denatured
Hazard to Others
Posts: 151
Registered: 7-8-2004
Location: -
Member Is Offline
Mood: HCl 50%?
|
|
Chitin deacetylation: 100°C or more, 50-60% NaOH, duration varies (from 15 minutes to 3 hours, 600-900 Watts). I use 316 steel when using
conventional heating, glass is out of question and even if there is some kind that can stand it, it will be very expensive.
Do I have to get a specialty ceramic to have this resistance against hot concentrated NaOH? or any ceramic I can get will hold?
Thanks
|
|
watson.fawkes
International Hazard
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by denatured | I use 316 steel when using conventional heating, glass is out of question and even if there is some kind that can stand it, it will be very expensive.
| Oh, "... and cheap". You didn't mention that in your first post. It would be possible to make a custom
microwave oven that used a stainless steel vessel as the oven, but you'd need to learn some microwave engineering to do it. It would likely need some
kind of closed-loop power supply control for the magnetron not to overheat the reaction vessel (or itself). None of this is cheap, certainly in time,
likely in materials.
So my next question is how much better is microwave heating than what you're doing now? In other words, where's the break even point for effort and
resources?
The really cheap answer is that you can sometimes just stick metal into ovens without a problem, but only certain ovens (top feed is best) and only
certain shapes of metal (those without sharp points and corners). Even then you'd need to have some feel for microwave physics to get it right. And
you still might blow out your oven.
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by watson.fawkes |
The really cheap answer is that you can sometimes just stick metal into ovens without a problem, but only certain ovens (top feed is best) and only
certain shapes of metal (those without sharp points and corners). Even then you'd need to have some feel for microwave physics to get it right. And
you still might blow out your oven. |
In which case you run across the street to the junk shop to get another second hand microwave oven!
Most bowl-like steel vessels shouldn't spark, IMHO...
|
|
turd
National Hazard
Posts: 800
Registered: 5-3-2006
Member Is Offline
Mood: No Mood
|
|
Oh, that's quite mild. Many ceramics will take that without problems, but they're
expensive. My first try would be a Teflon autoclave with thick walls. BTW: I've achieved over 1000°C in a 700W kitchen microwave. Careful!
Edit: If Teflon is compatible with microwave ovens, that is. No idea.
Edit2: Why microwave? Every cheap kitchen oven can do 200°C and temperature control is so much easier - just put a thermometer in there.
[Edited on 10-8-2010 by turd]
[Edited on 10-8-2010 by turd]
|
|
Sedit
International Hazard
Posts: 1939
Registered: 23-11-2008
Member Is Offline
Mood: Manic Expressive
|
|
It will not work at all if your intent is to have the Microwaves reach the reactants since they will reflect and absorb off of the steel never
reaching whats inside. However as long as there are not sharp corners for break out of the charge built up in the Stainless material you MIGHT get
away with it. As it stands however it seems useless to use a microwave over conventional heating in this case.
Knowledge is useless to useless people...
"I see a lot of patterns in our behavior as a nation that parallel a lot of other historical processes. The fall of Rome, the fall of Germany — the
fall of the ruling country, the people who think they can do whatever they want without anybody else's consent. I've seen this story
before."~Maynard James Keenan
|
|
Hexagon
Harmless
Posts: 45
Registered: 11-5-2010
Member Is Offline
Mood: Fanf*ckingtastic
|
|
On this same topic, would it be a good idea to put a magnet inside of a microwave? The idea would be to make a reflux apparatus with stirring inside a
microwave, using as stirrer a computer fan with magnets and a soup dish upside down to protect it, and a teflon coated magnet inside the flask one
would need to stir with the condersor coming out of the top part of the microwave. The mixture to be nucked would be a biphasic one (one of the phases
being aqueous)
|
|
zed
International Hazard
Posts: 2284
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
100 C isn't very hot. Hot NaOH will attack glass, but I don't know that it will dissolve away the walls of a beaker entirely. At least, not in the
time period you are suggesting.
Sacrifice a beaker. True, it'll never be the same. It won't be pretty anymore.
But, you will have a dedicated, ugly beaker, always on hand, for heating caustics.
|
|
Satan
Hazard to Others
Posts: 126
Registered: 1-5-2009
Member Is Offline
Mood: No Mood
|
|
Quote: |
Sparking and Metallic Samples
Many alloys interact with microwave energy and will heat sufficiently to melt plastic vessels; others accumulate
large electrical discharge potentials. One case, involving a large alloy sample melting through a container, has been
related to the authors. Several types of ferrous alloys were tested in which spark discharges were quite spectacular.
Discrete pieces (> 1 mm) of metallic samples should be avoided, because electrical arcs may occur between
individual sample pieces or between these alloys and the microwave cavity's metallic devices including the walls.
The formation and intensity of electrical sparks depend on the composition of the alloy and other conditions such as
electric field strength. Electrical arcs from inadequately grounded thermocouples constructed of 316 stainless steel
have been found to be sufficiently energetic to puncture 1/16 in Teflon(tm) PFA (39, 40). It has also been noted that
some concentrated solutions also exhibit sparking. Concentrated sodium hydroxide, copper nitrate, and nitric acid
have all been observed to discharge electrically within the solution.
|
Check if teflon coatings are available in your country, its one of possibilities to coat glass with it.
|
|
Fluorite
Hazard to Others
Posts: 139
Registered: 26-12-2018
Location: United Arab Emirates
Member Is Offline
|
|
Quick question:
can I decompose magnesium/calcium carbonate to oxide? Using a microwave
I saw a video about melting glass in microwave! https://m.youtube.com/watch?v=xwEQZw3KPWg
|
|
zed
International Hazard
Posts: 2284
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
The original poster might have succeeded with a glass or pyrex container, lined with HDPE or some other plastic. Not sure.
You want to do something that requires a lot more heat. Now, you can possibly achieve the heat.
But, what Microwavable Crucible will take that heat, and resist hot CaO?
Not impossible to displace the CO2 and H2O, by refluxing in Methanol or Ethanol. Leaving you with Magnesium Methoxide Etc... Or, Calcium Methoxide.
Which on hydrolysis would leave you with Ca(OH)2
or Mg(OH)2. But, it seems like an awful lot of work to get
something your can buy at the hardware store.
Ooops! I see you are in Tunisia. I have no idea what reagents you can obtain in Tunisia.
[Edited on 3-12-2020 by zed]
[Edited on 3-12-2020 by zed]
|
|