| Pages:
1
2
3
4 |
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
This stuff is not explosive, but if you ignite it, it will burn very fast. Try this with half a ml or so in a petri dish. Keep the rest of the stuff
far away from flame!
|
|
|
theAngryLittleBunny
Hazard to Others
Posts: 130
Registered: 7-3-2017
Location: Austria
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by woelen  | | This stuff is not explosive, but if you ignite it, it will burn very fast. Try this with half a ml or so in a petri dish. Keep the rest of the stuff
far away from flame! |
Thanks for that information, I'am on to making t-butyl hypochlorite next, because I heard that burns even faster.
|
|
|
theAngryLittleBunny
Hazard to Others
Posts: 130
Registered: 7-3-2017
Location: Austria
Member Is Offline
Mood: No Mood
|
|
Okay, I tried something and I feel like it's worth posting. I just made a little isopropyl hypochlorite by mixing 50g of 14% NaOCl with isopropanol
and acetic acid, and a green layer immediately seperated on top. But as I went to get a pipette, it suddenly violently decomposed with a crackling
sound O.o pretty scary, but also kinda fun. So for anyone playing with hypochlorite esters, just be a bit careful, they might blow up in your face.
[Edited on 26-3-2018 by theAngryLittleBunny]
|
|
|
Texium
|
Threads Merged
26-3-2018 at 12:59 |
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
I just tried making the isopropyl ester, but apparently this is much more unstable than the other esters I tried (methyl, ethyl and tert-butyl). I
prepared approximately 0.5 ml, but within one minute of its preparation, it made a very loud crackling noise. Then it became silent again, then it
made crackling noise again, and so on. I decided not to wait and see what happens further. I took a towel, wrapped it around my hand (thick layer of a
few cm) and then grabbed the test tube and dumped its content in the sink.
The reason I made this is for making a nice video for my website, and I decided to take isopropyl, because that is cheap and very common where I live.
I'll refrain from that, however. I'll try the tert-butyl variation again. That one is more stable.
[Edited on 18-2-20 by woelen]
|
|
|
DraconicAcid
International Hazard
Posts: 4332
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
Hypochlorites are commonly used to oxidize alcohols to ketones....why wouldn't you just get acetone from this reaction?
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
woelen
Super Administrator
Posts: 8012
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Under certain conditions, you can make hypochlorite esters, instead of ketones (or aldehydes).
If you add a mix of an alcohol and a weak acid (acetic acid or propionic acid is fine) to a solution of sodium hypochlorite, then you get the
hypochlorite ester and not the oxidized alcohol, e.g. ethanol yields CH3CH2OCl.
These hypochlorite esters are quite interesting and reactive compounds. E.g. CH3OCl is a gas, which on ignition explodes, CH3CH2OCl is a volatile
yellow liquid, which burns very fiercely when ignited. C(CH3)3OCl also is a yellow liquid, less volatile, but also very flammable. The isopropyl ester
apparently is more unstable than the others and decomposes spontaneously.
It is quite interesting to perform the experiments of making CH3OCl or CH3CH23OCl, by adding a mix of acetic acid and the alcohol with 4 to 5 times
its volume of concentrated bleach (10+ % of active chlorine). Only try this with small quantities (e.g. 0.5 ml of alcohol and 0.8 ml of acetic
acid). Scaling up may lead to very violent reactions and explosions.
|
|
|
| Pages:
1
2
3
4 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
