| Pages:
1
2 |
dumbsnake
Harmless
Posts: 3
Registered: 8-3-2007
Member Is Offline
Mood: No Mood
|
|
Aspirator/Water outlet for home
Hey all,
I have lurked a bit and I really like this forum. I finally gave in and bought a bunch of glassware. Unfortunately I don't have one of those
chem lab water spigots. I'd like to get something so that I can hook up my distillation setup. Also, I need to get an aspirator. I've been
searching around and everywhere I find they are selling products that I can't hook up to my faucet at home. I spent about an hour at the hardware
store trying to figure out a possibliity here. What have you all done? Thanks for any help.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Are you trying to connect to a standard US kitchen sink with aerator?
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
dumbsnake
Harmless
Posts: 3
Registered: 8-3-2007
Member Is Offline
Mood: No Mood
|
|
That is what I have, but I took off the aerator and measured it and everything. I'm open to any ideas that could work. My sink head is 13/16" with
27 thread.
[Edited on 20-4-2007 by dumbsnake]
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
I have one that looks like the one on wikipedia, or at least in terms of connections. http://en.wikipedia.org/wiki/Aspirator
It does not fit to standard faucet screw threads, so I brought the aspirator to home depot and asked the guy in home depot's plumbing section to help
me get all the connectors to connect it to my tap. He found all necessary connectors within 40s or so.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
This is from an earlier post of mine:
| Quote: |
I use a kitchen sink tap with internal (female) threads. I bought a chrome plated brass aereator with the same thread size (only male), gutted it, and
soldered my brass aspirator to it.
|
The soldering is a little tricky, but it worked.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
bio2
Hazard to Others
Posts: 447
Registered: 15-1-2005
Member Is Offline
Mood: No Mood
|
|
If you can't readily find the adapter parts just use a
piece of plastic tubing secured with 2 hose clamps.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Here's a photo of the adaptor I made using an aereator and a brass 1/2" x 3/8" coupling, pipe threads. As you can see the soldering job is crude.
But it is watertight and worked just fine. Aspirators come with 3/8" male pipe threads in my experience.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
kaviaari
Hazard to Self
Posts: 80
Registered: 21-12-2005
Location: Finland
Member Is Offline
Mood: Going green
|
|
The easiest way of dealing with this is to take a rubber stopper and some glass tubing. Fit the stopper with about 5cm of glasss tubing snugly to the
faucet and that's it. When using aspirator I fit the in-end of the aspirator to another stopper and secure it to the faucet with clamp.
|
|
|
MadHatter
International Hazard
Posts: 1339
Registered: 9-7-2004
Location: Maine
Member Is Offline
Mood: Enjoying retirement
|
|
Barbed Connector
Magpie soldered his own pieces together and made a connector. I found a combination
of parts and Home Depot that ends up at a barbed connector off my faucet. It just
took some searching and some Teflon tape to make a working arrangement.
From opening of NCIS New Orleans - It goes a BOOM ! BOOM ! BOOM ! MUHAHAHAHAHAHAHA !
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
you can go over the faucet with plastic tubing and a hose clamp. Then over the aspirator with tubing and another hose clamp. You can get a lab type
faucet .. ie one with a high curve at home depot for under $60. And while you're there you could shop for connecting hardware to go to the inside
female threads in the faucet. Finally, I had an apsirator that was designed for emptying water beds and was made to hook to an outside faucet. This
worked well on laundy sinks and may still be available.
|
|
|
visitation123
Harmless
Posts: 34
Registered: 25-8-2006
Member Is Offline
Mood: No Mood
|
|
environment
water aspirators using faucets as you call them in your part of the world is a waste of water, forgetting the hassles required to connect it.
Why don't you focus your efforts on building an aspirator station? All your missing is a pond pump.
See here:
.
http://www.erowid.org/archive/rhodium/chemistry/equipment/as...
http://www.erowid.org/archive/rhodium/chemistry/equipment/pi...
http://www.erowid.org/archive/rhodium/chemistry/equipment/pi...
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
or buy a vacuum pump on ebay of labx for less than the cost of one of these time and space consuming projects
|
|
|
MadHatter
International Hazard
Posts: 1339
Registered: 9-7-2004
Location: Maine
Member Is Offline
Mood: Enjoying retirement
|
|
Vacuum Pump
I have a vacuum pump but there's no way in hell I'm going to use it for nitric acid vacuum
distillation. My glass aspirator is used for that purpose.
From opening of NCIS New Orleans - It goes a BOOM ! BOOM ! BOOM ! MUHAHAHAHAHAHAHA !
|
|
|
visitation123
Harmless
Posts: 34
Registered: 25-8-2006
Member Is Offline
Mood: No Mood
|
|
Exactly, without modification the aspirator passes distillates directly into solution.
|
|
|
uchiacon
Hazard to Self
Posts: 87
Registered: 3-7-2009
Location: The Jungle(neezeelund)
Member Is Offline
Mood: Financial
|
|
However a vacuum pump can go far below an aspirator, and if you can get one cheaply (under $100) it might be best to use that with a vapour trap yes?
10torr or less for nitric distilatin would mean that it'd boil at a very low temp.
|
|
|
kclo4
National Hazard
Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline
Mood: No Mood
|
|
The aspirator I've acquired I got to hook directly to my hose outside. I've then attached a long tube into my work place.
I have a several aspirators that are stuck onto the faucets they've been connected to for probably 50 years. I also have one other set up that can
also connect to the hose. As for the sinks I don't know if they are standard sinks, and the aspirators are attached in a weird way but if that is of
any interest to you we could make a trade or something. PM if you want I guess.
|
|
|
Phosphor-ing
Hazard to Others
Posts: 246
Registered: 31-5-2006
Location: Deep South, USA
Member Is Offline
Mood: Inquisitive
|
|
In the US this is a quite affordable option.
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnu...
"The nine most terrifying words in the English language are: 'I'm from the government and I'm here to help.'" -Ronald Reagan
|
|
|
uchiacon
Hazard to Self
Posts: 87
Registered: 3-7-2009
Location: The Jungle(neezeelund)
Member Is Offline
Mood: Financial
|
|
I think I might try to design my own aspirator, although my limited means may cause some problems. I found a good book named "organic chem lab
survival guide" by James Zubrick. It has some good diagrams in it for the aspirator, vapour traps etc.
So, lets say I have a slightly smaller inlet tube flowing into a slightly large T joint with the adjecent part with a hose barb for a vacuum tube. So
theres still a tiny gap between the water flowing through the T joint and the T joint itself. So I'd assume that the tiny gap would allow the venturi
effect and it would work. And is it best to have the outlet tapering in or out? I will probably find it hard to make a tapered outlet, but just in
case, which is better?
Alternatively, a T joint with an icing nozzle in it( I think this was discussed somewhere) which would be similiar to this diagram.
The icing nozzle would be better than just a smaller tube going into a larger one I presume? More pressure = bigger vacuum?
Oh, and a last thing, lab aspirators will always outperform home made ones right? I might be able to get a metal one from the uni, but I'll try and
make this one anyway.
|
|
|
kclo4
National Hazard
Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline
Mood: No Mood
|
|
I remember frogfot's website had a nice DIY aspirator, does anyone happen to have his pages saved? His site has unfortunately gone under, I've been
looking for an archive of it for a while, I haven't search to hard, but I haven't had much luck.
|
|
|
Klute
International Hazard
Posts: 1378
Registered: 18-10-2006
Location: France
Member Is Offline
Mood: No Mood
|
|
I really don't think it worth the hassle of buikding your own aspirator.. it's the kind of thing you are better off just buying, they are cheap and
relatively availble.. Very precise measure are required to get a decent vacuum, not just any T shaped plumbing will do the trick..
Once you have that piece, construction a aspirator station is pretty simple and cheap, and saves alot of water, and able sone to neutralize any fumes
that are trapped int he water. Just add some Na2CO3 to the water and a smalll amount of TCCA or similar to avoid rusting and molding/rotting of the
wtaer (thanks to Bio for this tip). Always worked wonders for me, get routine 25mmHg with cold water with a teflon aspiratoir that cost me 20e..
\"You can battle with a demon, you can embrace a demon; what the hell can you do with a fucking spiritual computer?\"
-Alice Parr
|
|
|
uchiacon
Hazard to Self
Posts: 87
Registered: 3-7-2009
Location: The Jungle(neezeelund)
Member Is Offline
Mood: Financial
|
|
What did visitation say about a pond pump?
My pump is rated for 30 PSI at 46L/min, I guess I just have to sell it and buy a less powerful one then.
Any suggestions for a low L/min pump with high PSI?
I saw somebody had a 120PSI pump with a 5L/min flow rate on trademe...
Would a beverage pump work? or would it cough out after a bit? Coz all these pond pumps seem to be A. submersible and B. not high enough pressure.
[Edited on 04-07-09 by uchiacon]
[Edited on 04-07-09 by uchiacon]
|
|
|
Contrabasso
Hazard to Others
Posts: 277
Registered: 2-4-2008
Member Is Offline
Mood: No Mood
|
|
There is a UK lab supplier doing a polypropylene filter pump for about £12 and a couple of other filter pumps in different materials for lots more
money. Does anyone have a UK supplier for a glass filter pump?
I too do not want to pull 99% nitric through a mechanical pump with pump oil!
I wondered whether the V2O5 process for H2S04 could be driven by a filter pump pulling the SO3 into recirculating dilute acid.
|
|
|
Inoxia
Harmless
Posts: 12
Registered: 2-9-2009
Member Is Offline
Mood: No Mood
|
|
To recirculate the dilute (and eventually conc) acid you would need a completly corrosion proof pump because otherwise it would get attacked by the
acid.
|
|
|
watson.fawkes
International Hazard
Posts: 2793
Registered: 16-8-2008
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Contrabasso  | | I wondered whether the V2O5 process for H2S04 could be driven by a filter pump pulling the SO3 into recirculating dilute acid.
|
You don't want to be dissolving SO3 directly in anything like a dilute solution. That reaction is violently
exothermic, which is why in a commercial plant they dissolve it in concentrated acid. The now-even-more concentrated acid is diluted (again
exothermic) elsewhere, again where they can manage the heat release.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
It's not just the exothermic nature, it's that the SO3 tends to form fine droplets of H2SO4 that are difficult to collect or absorb into dilute acid
or water, but concentrated H2SO4 absorbs the SO3 without the formation of droplets. With diluted acid the SO3 is in part reacting with the water
vapour, that's the source of the fine droplets; acid of a high enough concentration has very little water vapour over it.
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
