emrebjk
Hazard to Others
Posts: 108
Registered: 22-1-2005
Location: Zonguldak/TURKEY
Member Is Offline
Mood: No Mood
|
|
searching water mixable chlorine solvent
for a catalytic reaction I need a chlorine solvent like (CH2CL2, CCL4). But that solvent should be mix with water. Do you know such a solvent??
|
|
Nicodem
Super Moderator
Posts: 4230
Registered: 28-12-2004
Member Is Offline
Mood: No Mood
|
|
I always find this attitude of asking a question without providing any useful information fascinating. Is there a banner saying "Members of
ScienceMadness can read your mind!" when registering?
|
|
BromicAcid
International Hazard
Posts: 3255
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Most of the good chlorine solvents, as you likely know, are non-polar so they won't mix with water. You could always just stir the heck out of it
though and form an emulsion. Chlorine itself is soluble in water as well, just not to a great extent. So as Nicodem said, if you give us some more
reaction conditions, what you are trying to accomplish, we might be able to help you. I mean, are you bubbling chlorine into something, generating it
in situ, or going for using some kind of chlorinating reagent?
Besides, let's say you have solvent A, which is soluble in water, and also in which chlorine is soluble, I have no clue what you are trying to
accomplish with it. Are you trying to make an aqueous mixture of that solvent able to dissolve more chlorine than water alone? Or are you trying to
chlorinate something in that solvent and then dissolve it all in water together? There are too many unknowns.
[Edited on 3/25/2007 by BromicAcid]
|
|
emrebjk
Hazard to Others
Posts: 108
Registered: 22-1-2005
Location: Zonguldak/TURKEY
Member Is Offline
Mood: No Mood
|
|
In the catalytic reaction metal oxidised by the Cl of CHCl3 or like that. At this point CHCl2. radical forms. That radical starts the polimerization.
My complexes are only water soluble. So that I need a chlorine solvent which can be mixed with water and forms a radical.
|
|
UnintentionalChaos
International Hazard
Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline
Mood: Nucleophilic
|
|
If it is a radical-induced polymerization, then very few radicals are required, correct? Chloroform CHCl3 is soluble at 8g/L at room temperature and
more if you react at a higher temperature. That means for every liter of solution, you get .067 mol of radicals (assuming complete conversion, which
is never the case). Thats forty billion, trillion polymer chains per liter of reaction solution. I imagine that that is plenty, although I am curious
what exactly you are polymerizing. Also, chloroform should sink to the bottom of the water solution and sit over the metal, so getting them in contact
is not a problem.
Department of Redundancy Department - Now with paperwork!
'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
|
|
emrebjk
Hazard to Others
Posts: 108
Registered: 22-1-2005
Location: Zonguldak/TURKEY
Member Is Offline
Mood: No Mood
|
|
radical forms only with transition metal. 1f in reaction there is no metal complex, polymerization is not occuring. So radical amount is related to
metal amount. For example think a Ru(II) complex. This will oxidised Ru(III)-Cl and CHCl2 radical forms. Then we add methyl methacrylate monomer to
the reaction. Polymerization starts with that radical and MMA polimerized. If chloroform sink to the bottom, it cannot react with complex so the
radical and polymerization will not occur.
|
|