| Pages:
1
2 |
PlatinumCal99
Harmless
Posts: 18
Registered: 18-11-2006
Location: Pluto
Member Is Offline
Mood: Apathetic
|
|
Oil bath
What does everyone here use as a container for their oil bath? A huge 5 L flask or some pyrex bowl from the grocery store?
|
|
|
BromicAcid
International Hazard
Posts: 3253
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
A metal dog food dish. They stand upright easily, don't tip over, and heat up uniformly without worries of thermal shock. For small projects though
I use a pyrex beaker.
|
|
|
evil_lurker
National Hazard
Posts: 767
Registered: 12-3-2005
Location: United States of Elbonia
Member Is Offline
Mood: On the wagon again.
|
|
8 quart aluminum pressure cooker, sans lid... it easily accomodates a 3 liter flask... not for sure but I bet it would do a 5L flask, a 6 would be
kinda iffy though.
For oil, Wal-mart brand heavy mineral oil laxative.
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Metal has to be a safer bet than glass, and it conducts heat better.
|
|
|
Boomer
Hazard to Others
Posts: 190
Registered: 11-11-2005
Member Is Offline
Mood: No Mood
|
|
Spaghetti pot on kitchen stove, with triac in the house wiring for better heat control. 
Have to replace the engine oil with veggie oil though, neighbours start to thing I've got a garage in the second floor flat. 
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
What would the neighbours think if they saw you buy a few pints of medicinal parafin?
Vegie oil is easier to get (relatively environmentally benign) and the safe working temperatures of various oils are well documented. IIRC peanut oil
is good- but check it rather than taking my word for it.
|
|
|
Baphomet
Hazard to Others
Posts: 211
Registered: 19-11-2006
Member Is Offline
Mood: No Mood
|
|
Peanut oil in 2Lt beaker but the dog food bowl sounds like a better idea!
|
|
|
evil_lurker
National Hazard
Posts: 767
Registered: 12-3-2005
Location: United States of Elbonia
Member Is Offline
Mood: On the wagon again.
|
|
Ever had to clean up sticky polymerized veggie oil?
I will never use that stuff again.
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Yes, It comes off reasonably well with caustic.
|
|
|
Chris The Great
Hazard to Others
Posts: 463
Registered: 29-10-2004
Location: Canada
Member Is Offline
Mood: No Mood
|
|
Why not motor oil? It's meant for high temperatures and it's cheap.
|
|
|
PlatinumCal99
Harmless
Posts: 18
Registered: 18-11-2006
Location: Pluto
Member Is Offline
Mood: Apathetic
|
|
Most of the metal dog food bowls and kitchen pots are not perfectly flat on the bottom. Towards the center of the bottom part of the pot it comes up a
little so there is no contact with whatever the pot is resting on. Have the rest of you been able to find pots with flatter bottoms, or do you use
these ones regardless of the lower surface area? I've checked local grocery stores, Wal-Mart, pet stores, etc. I'm sure they would work, but I'm
looking for something that would work better.
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
I use a small copper pot. The bottom is very slightly concave, which is nice because my hotplate is slightly convex.
|
|
|
prole
Hazard to Self
Posts: 94
Registered: 4-8-2005
Member Is Offline
Mood: No Mood
|
|
I use Visions Cookware by Corning. Entirely glass, never had any problems with it. No longer made, got it off ebay. I can't use any larger than a
2L RBF though, they're not deep enough. Peanut oil for the bath itself, but when it gets a little old, it stinks the whole house up. Metal pots
would be more convenient were it not for the magnetic stirring issues... that's what boiling stones are for, I s'pose.
|
|
|
Baphomet
Hazard to Others
Posts: 211
Registered: 19-11-2006
Member Is Offline
Mood: No Mood
|
|
Follow up.. I've tried the metal bowl idea and it's good. I've noticed that water has an advantage if you are dealing with reactions that need to be
kept at or near 100c.
A temp measurement of peanut oil yesterday gave 250c and an answer to why the reaction I was trying did not give the expected results.
|
|
|
microswitch
Harmless
Posts: 27
Registered: 26-11-2006
Member Is Offline
Mood: No Mood
|
|
What sort of temperatures can you get veggie oil up to before it starts to boil? Alas, wikipedia was no help in answering this query. 
\"Conspiracies hatched in hell do not have angels as witnesses,\" Hough said.
|
|
|
joeflsts
Hazard to Others
Posts: 226
Registered: 14-1-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by microswitch
What sort of temperatures can you get veggie oil up to before it starts to boil? Alas, wikipedia was no help in answering this query. |
This site gives the smoke point of most common vegetable oils.
http://missvickie.com/howto/spices/oils.html
Joe
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
joeflsts has it right, it's the smoke point and then the flash point you want to worry about. Refined peanut, soy, and safflower oils are about the
best out of the common cooking oils, but they do top out at about 220 C.
|
|
|
Sauron
International Hazard
Posts: 5351
Registered: 22-12-2006
Location: Barad-Dur, Mordor
Member Is Offline
Mood: metastable
|
|
A stainless steel dish or pot with dimensions entirely depending on the size of flask you are going to heat.
A stirring hotplate underneath, a thermocouple probe and a digital thermometer, a spinbar in the flask and maybe another in the bath. I have not quite
figured out why commercial oil baths sell. Unless the lab's procurement clerk is on the take?
Mineral oil or one of the high temp silicone oils is best but, I have used a good grade of peanut oil with very good results. Just do your cleanup
before it dries on your glassware.
A word of caution:
Hot plate manufacturers advise AGAINST using steel vessels most likely their concerns are with inductive coupling.
As I have so often violated their injection...maybe they are being overly cautious. Opinions?
GLYCERIN is an excellent heating medium, and was used to heat absinthe stills in 19th century so that local overheating from direct heating would not
char the herbs. As the bp is quite high this would do in many instances...although perhaps not for heating nitrating mixtures, or permanganate
oxidations, for obvious safety reasons.
[Edited on 20-1-2007 by Sauron]
|
|
|
joeflsts
Hazard to Others
Posts: 226
Registered: 14-1-2006
Member Is Offline
Mood: No Mood
|
|
| Quote: | GLYCERIN is an excellent heating medium, and was used to heat absinthe stills in 19th century so that local overheating from direct heating would not
char the herbs. As the bp is quite high this would do in many instances...although perhaps not for heating nitrating mixtures, or permanganate
oxidations, for obvious safety reasons.
[Edited on 20-1-2007 by Sauron] |
The MSDS for Glycerin indicates a flash point of 199C. I guess it is safe to say that most MSDS cautions err on the side of worst case.
This could cause alarm since Glycerin, when decomposing, produces Arcolein.
Joe
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
I never had a problem with pyrex cookware. I forget what its called; pinkish stuff, heavy walled. For oil I use 3 dot break fluid-higher temps than
most oils without decomposing. The nice thing about glass is I can sit the apparatus on a stirrer hot plate and stir through the vessel.
|
|
|
picketfence
Harmless
Posts: 16
Registered: 15-1-2007
Member Is Offline
Mood: No Mood
|
|
Here's a list of bath fluids and they're boiling points:
http://www.hartscientific.com/products/bathfluid.htm
|
|
|
Misanthropy
Hazard to Self
Posts: 69
Registered: 24-3-2005
Member Is Offline
Mood: Variable
|
|
Doesn't brake fluid readily absorb atmospheric moisture???? Hence, old, unchanged/exposed fluid boiling in the brake lines under panic braking? (yes,
yes, I know you're keeping it hot) 
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
oil bath
I use visionware too and a big heavy pyrex bowl from the thrift store. I use 3 dot brake fluid. Sand is another medium mentioned in lab manuals.
The stainless dog dishes would keep the magnetic stirrer from working wouldn't they?
|
|
|
evil_lurker
National Hazard
Posts: 767
Registered: 12-3-2005
Location: United States of Elbonia
Member Is Offline
Mood: On the wagon again.
|
|
I can tell you right now that extra heavy mineral oil laxative from walmart is good to 200ºC without very much smoking at all... and it should be
able to take at least 225ºC with not much of any problem... best of all it doesn't polymerize!
All the brake fluids I've tried can't take those temps. Plus they emit toxic fumes when they get that hot!
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
I've gone to Dot 4 brake fluid which is a silicon oil and the price reflects this. I keep it too hot to pick up water and otherwise covered. I use a
commercial deep fat fryer my partner picked up at the thrift store. It's a pretty amazing little find. The controller maintains temperatures between
50-250 *C at +/- 0.5*C or less. Once a temperature is established the thermometer just doesn't show any change and it's not hard to pin down a temp.
It loves to sit at 100*C for hours at a time. The fryer is gun metal gray with no extra stuff on it. We use a jack stand to handle it and we put
some duct tape on the stand surface and when using a stirring motor we fix the bath in place with tie wire just to be extra safe.
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
