Conure
Harmless
Posts: 47
Registered: 6-2-2023
Location: Schweden
Member Is Offline
|
|
Should I buy this furnace on ebay?
I would like a powerful hot plate since my burner isn't good enough and I found this chinese made furnace on ebay. Claims ro reach temperatures of
1200c. Too good to be true?
https://www.ebay.co.uk/itm/315398459661?chn=ps&_ul=GB&am...
Fire is good. Fire is life.
|
|
|
B(a)P
International Hazard
Posts: 1139
Registered: 29-9-2019
Member Is Offline
Mood: Festive
|
|
I see no reason why it couldn't get that hot. The issue with this is, what happens when you inevitably get a spill? The element will very quickly get
destroyed. It depends what you are trying to do with it though.
|
|
|
RedDwarf
Hazard to Others
Posts: 166
Registered: 16-2-2019
Location: UK (North West)
Member Is Offline
Mood: Variable
|
|
I clicked on the link through curiosity and then on another similar looking item that Ebay suggested that only claimed 400C. Both had a spec sheet
that showed the highest temperature ("heating wire"). The spec sheet (and photos) for both is identical , model numbers, power , size and all the text
apart from your link shows "Highest temperature 1200C (Heating wire)" whilst the other shows "Highest temperature 400C (Heating wire)". Personally
looking at the construction I'd hope that the temperature never came anywhere close to 1200C!
|
|
|
Texium
Administrator
Posts: 4580
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
Looks sketchy. It would be a much better idea to invest in a decent hotplate/stirrer that can go to a more reasonable temperature, like 400 °C.
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Should I buy this furnace on ebay?
Yes, then you can review it for others 
Personally, I would not buy it.
This type https://www.ebay.co.uk/itm/195704686574
was my favourite, good for many uses, no stirring.
Cheap enough to abuse until the temp. controller dies, then an external 'dimmer' makes it better than new.
I've come to value good stirring more and more,
So I like a hotplate or mantle, with stirring.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Dr.Bob
International Hazard
Posts: 2732
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
This is not a furnace, it is a hotplate without a top. The wire may get to 1200C, but it won't be able to heat things up to more than 400C, even
that is a stretch without an enclosure.
|
|
|
Conure
Harmless
Posts: 47
Registered: 6-2-2023
Location: Schweden
Member Is Offline
|
|
Quote: Originally posted by B(a)P  | | I see no reason why it couldn't get that hot. The issue with this is, what happens when you inevitably get a spill? The element will very quickly get
destroyed. It depends what you are trying to do with it though. |
My plan is to make MoO3 by thermal decomposition of ammonium molybdate. I have tried with a steel vessel over a burner and it's very a poor method
because the temperature is barely high enough. So I need a more powerful heat source. Something that makes steel glow red.
Fire is good. Fire is life.
|
|
|
Conure
Harmless
Posts: 47
Registered: 6-2-2023
Location: Schweden
Member Is Offline
|
|
| Quote: Originally posted by Texium | | Looks sketchy. It would be a much better idea to invest in a decent hotplate/stirrer that can go to a more reasonable temperature, like 400 °C.
|
400c is not enough for me. My steel vessel placed over a burner gets a dull red glow at the center and it's not enough practical use. I need the whole
bottom to glow red.
Fire is good. Fire is life.
|
|
|
Conure
Harmless
Posts: 47
Registered: 6-2-2023
Location: Schweden
Member Is Offline
|
|
| Quote: Originally posted by RedDwarf | | I clicked on the link through curiosity and then on another similar looking item that Ebay suggested that only claimed 400C. Both had a spec sheet
that showed the highest temperature ("heating wire"). The spec sheet (and photos) for both is identical , model numbers, power , size and all the text
apart from your link shows "Highest temperature 1200C (Heating wire)" whilst the other shows "Highest temperature 400C (Heating wire)". Personally
looking at the construction I'd hope that the temperature never came anywhere close to 1200C! |
Too good to be true then. I appreciate all your answers people.
Fire is good. Fire is life.
|
|
|
Rainwater
National Hazard
Posts: 919
Registered: 22-12-2021
Member Is Offline
Mood: indisposition to activity
|
|
Electric stove element. $10
Old ss pot with lid $10
Kyle wool $50
1000w dimmer $20
You can get fancy with a pid controller off amazon.
"You can't do that" - challenge accepted
|
|
|
Texium
Administrator
Posts: 4580
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
| Quote: Originally posted by Conure | | Quote: Originally posted by Texium | | Looks sketchy. It would be a much better idea to invest in a decent hotplate/stirrer that can go to a more reasonable temperature, like 400 °C.
|
400c is not enough for me. My steel vessel placed over a burner gets a dull red glow at the center and it's not enough practical use. I need the whole
bottom to glow red. |
Then a hotplate is not the right tool for the job
|
|
|
bnull
Hazard to Others
Posts: 431
Registered: 15-1-2024
Location: South of the border, wherever the border is.
Member Is Offline
Mood: Dazed and confused.
|
|
| Quote: Originally posted by Conure | | I would like a powerful hot plate since my burner isn't good enough and I found this chinese made furnace on ebay. Claims ro reach temperatures of
1200c. Too good to be true? |
It's more like 1200 degrees in the Rankine scale (393 °C).
Why not a charcoal furnace, like this?
Quod scripsi, scripsi.
B. N. Ull
P.S.: Did you know that we have a Library?
|
|
|
Deathunter88
National Hazard
Posts: 519
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
I have that exact same hot plate that I used to distill sulfuric acid and it’s the best I have ever used for that purpose. The trick is to clamp
your boiling flask a few millimeters above the surface and then you can distill sulfuric acid with zero bumping! I think it’s because connective
heat is so even that you don’t get the hotspots which cause bumping.
|
|
|
Conure
Harmless
Posts: 47
Registered: 6-2-2023
Location: Schweden
Member Is Offline
|
|
| Quote: Originally posted by Deathunter88 | | I have that exact same hot plate that I used to distill sulfuric acid and it’s the best I have ever used for that purpose. The trick is to clamp
your boiling flask a few millimeters above the surface and then you can distill sulfuric acid with zero bumping! I think it’s because connective
heat is so even that you don’t get the hotspots which cause bumping. |
Do you know how hot it gets? Enough to make stuff glow red?
Fire is good. Fire is life.
|
|
|
DrRadium
Harmless
Posts: 17
Registered: 30-11-2021
Member Is Offline
|
|
| Quote: Originally posted by Conure |
400c is not enough for me. My steel vessel placed over a burner gets a dull red glow at the center and it's not enough practical use. I need the whole
bottom to glow red. |
If you are here, you're probably comfortable with enough with electricity to make your own to be able to heat to about 700C, hot enough for thermal
decomposition and reformation into crystalline o-MoO3 in air.
For a less expensive option, you can make a simple furnace from some insulating firebrick, a standard PID controlller, solid state relay, ceramic
protected type K thermocouple, and a heating element of about 500W or more (you could use a 1000W to heat a larger area if desired). I made one to do
heating of a small area to about 700C-800C making manganese blue. It was made deliberately using loose firebrick to allow gasses (in my case NOx, in
your case ammonia and NO) to escape and run it outdoors. It uses two bricks with carved out channels to hold the elements, one brick with the
thermocouple both wired (with quick release plugs) to a controller box holding the PID controller and SSR, wired to a standard electrical cord. I
just pile up bricks as needed around the heating and thermocouple bricks. I did a short write up with links to images at https://www.reddit.com/r/DIYPigments/comments/16e4jc2/commen...
EDIT corrected quote formatting
[Edited on 29-6-2024 by DrRadium]
[Edited on 29-6-2024 by DrRadium]
|
|
|
Sulaiman
International Hazard
Posts: 3692
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Charcoal with forced air
(eg https://www.ebay.co.uk/itm/204819849468)
will get steel orange hot, easily melt aluminium etc.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Deathunter88
National Hazard
Posts: 519
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Conure | | Quote: Originally posted by Deathunter88 | | I have that exact same hot plate that I used to distill sulfuric acid and it’s the best I have ever used for that purpose. The trick is to clamp
your boiling flask a few millimeters above the surface and then you can distill sulfuric acid with zero bumping! I think it’s because connective
heat is so even that you don’t get the hotspots which cause bumping. |
Do you know how hot it gets? Enough to make stuff glow red? |
You can get a steel crucible sitting directly on the element to a dull red, but certainly not enough to melt metals (it does soften aluminum but not
hot enough to get it fluid enough to cast).
|
|
|
zed
International Hazard
Posts: 2283
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
I am proud to say that I improvised my own furnace. I needed to de-temper a cast metal weight lifting plate in order to render it soft enough, to
easily machine.
I simply placed the plate on one of my Electric Range-top elements, and then placed an inverted cast-iron frying pan over the top of the whole thing
to contain the heat. This seems to have worked; but I'm not sure.
Of certainty though, is that this experiment quickly burned out the heating element, and also the temperature control switch.
Thereafter, cooking at my house, became much more difficult.
Eventually, I broke down and invested in some Tungsten Carbide drill bits. It circumvented my machining problems.
And, over time, I have, sort of, rehabilitated my kitchen stove. Oh, it will never again be the valiant creature that it once was; but it will make
do, until the next girlfriend arrives. And then of course, I will have to buy a new stove.
|
|
|
Conure
Harmless
Posts: 47
Registered: 6-2-2023
Location: Schweden
Member Is Offline
|
|
| Quote: Originally posted by Conure | | Quote: Originally posted by Deathunter88 | | I have that exact same hot plate that I used to distill sulfuric acid and it’s the best I have ever used for that purpose. The trick is to clamp
your boiling flask a few millimeters above the surface and then you can distill sulfuric acid with zero bumping! I think it’s because connective
heat is so even that you don’t get the hotspots which cause bumping. |
Do you know how hot it gets? Enough to make stuff glow red? |
It looks like the furnace uses the american type of celectrical plug right? Since I live in europe, can I simply use an adapter to make it fit eu
sockets?
Fire is good. Fire is life.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
