Diachrynic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 222
Registered: 23-9-2017
Location: western spiral arm of the galaxy
Member Is Offline
Mood: zenosyne
|
|
Cleaning the cooling jacket of a condenser
This is just to report on something interesting I noticed, maybe it's of use to others if they find themselves in a similar situation.
I had acquired a jacketed coil condenser with some really nasty stains in the cooling mantle. The coil was full of brown stains, and there were some
thick white deposits in the outer cooling jacket, all over, so it looked like cooling water had evporated several times in the condenser.
First I soaked the condenser in ~500 g/L citric acid solution overnight (I used a syringe to inject it into the mantle until it was full), which
cleaned up the brown stains quite nicely and left me with a neon green solution (probably iron?). The white deposits were still very visible however.
A mixed cleaner containing citric, tartaric and malic acid fared similarly.
So it was suggested to me to try soaking in strong sodium carbonate solution, since sulfates would probably be converted into the carbonates, which
then should be much more susceptible to acid. I filled the condensers cooling jacket with a strong solution of Na2CO3 and let it
sit. Curiously, after a few hours already I could see the stains dissolve, which was not what I was expecting. After sitting overnight, pretty much
all the thick white deposits are now gone. (Then I rinsed with another portion of citric acid and then clean water several times.)
It was suggested to me it might've be a silicatic stain, but other people said old dried silicates are probably not that much easier to dissolve than
the glass itself - and the stain really did dissolve and not just crumble off like in a base bath.
Either way, this managed to clean the condenser really well off the water stains. Maybe it helps someone who faces something similar.
we apologize for the inconvenience
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3646
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Nice to know, thanks.
Is there a treatment for the inner surface of the cooling jacket that will minimise the formation or retention of bubbles?
(a wastefully high water flow rate helps remove bubbles,
I've read that a West condenser addresses this problem, but,
if efficiency is necessary then I use my Dimroth
For 10/14 I only have short fat Leibigs so a treatment would be good,)
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Sir_Gawain
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 335
Registered: 12-10-2022
Location: Due South of Due West
Member Is Offline
Mood: Way less sad
|
|
I've found sodium carbonate and percarbonate to be very effective cleaners, no matter what the stain is.
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
Chemetix
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 375
Registered: 23-9-2016
Location: Oztrayleeyah
Member Is Offline
Mood: Wavering between lucidity and madness
|
|
Reddish brown stains are iron, so a hydrochloric acid soak generally does the trick.
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
In my lab red stains are from microbial contamination/films. They are stubbornly resistant to most things other than mechanical manipulation with
small brushes which on some condensers is out of the question. A concentrated ABF solution though makes short work of them. I've also one one
occasion used a small piece of pipe cleaner and pushed it through with water pressure.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2692
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I often clean condensers in HCl, sodium dithionate also is good to remove iron stains. Of course the base bath often will remove enough glass to take
off any stains. I use one daily at work for various goo and gunk to remove.
|
|
AnonGuy
Harmless
Posts: 5
Registered: 7-9-2023
Member Is Offline
Mood: No Mood
|
|
Yep I'd try strong sodium carbonate solution as suggested, H2O2 (30%+), HCl, or sulphuric acid. My last line of defence is piranha fluid, which I'm
currently using to clean a flask of unknown nastiness.
|
|