woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
sulfur charring?
Recently, I did some experiments with sulfur. I did the well-known experiment of heating it to just above its melting point. This gives a mobile
yellow liquid. On stronger heating, the liquid turns dark red and becomes more viscous. At a certain point, the liquid is so viscous that you can keep
the small beaker upside down without pouring out the sulfur. On cooling down, the liquid becomes more mobile again.
All of this is perfectly according to theory in the text books . . .
However, on cooling down, and finally on solidification, the color of the sulfur does not revert to its original color. It gets a more ochre color and
if the heating was very strong (such that brown/red gaseous sulfur is formed), then the molten sulfur reverts to a dirty looking green (pale yellow,
contaminated with a color like olives). On very long standing of the solidified sulfur (several days), the color somewhat comes closer to the original
yellow, but it never becomes as nice bright yellow as the original solid.
I have done this experiment with so-called flowers of sulfur of high purity (99.99% or so, according to seller) and also with another sample, sold
specifically for the purpose of using it as fuel in pyrotechnic mixes. This sulfur has a purity of 99.95% according to its label. But none of my
samples of sulfur give the nice pure color of the sulfur on cooling down and solidifying.
Is this also the observation of others over here? What kind of impurities could cause this change of color? Organics? Absorption of oxygen from air,
leading to colored compounds, contaminating the sulfur?
On the internet there are several pages about melting sulfur, but none of them covers this topic. Probably most people do not observe that closely and
only look at the behavior of melting, becoming viscous and that kind of well-known things.
[Edited on 22-6-21 by woelen]
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
https://en.wikipedia.org/wiki/Allotropes_of_sulfur
You will probably find the answer there.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
pantone159
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 588
Registered: 27-6-2006
Location: Austin, TX, USA
Member Is Online
Mood: desperate for shade
|
|
I understood the greenish looking sulfur after melting to be the monoclinic crystal form, instead of the stable, and bright yellow, orthorhombic form
that you started with.
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Sounds like S6 instead of S8.
I didn't think that would form without a chlorine catalyst.
It should not be stable at room temperature and should eventually revert to S8 alpha form.
|
|
Darien
Harmless
Posts: 25
Registered: 19-1-2017
Member Is Offline
Mood: No Mood
|
|
All commercial sulfur has trace amounts of hydrocarbons in it. When heated the sulfur takes the hydrogen and leaves the carbon behind. I’ve tried
getting hold of carbon free sulfur but with no luck. Even the good stuff in the lab turns dark when heated strongly.
|
|
Triflic Acid
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 486
Registered: 27-9-2020
Member Is Offline
Mood: Slowly Oxidizing into Oblivion
|
|
Actually, I don't think this is carbon. I made SCl2 the other day, and in the boiling flask where the sulfur was, there was a bunch of black residue.
This was not attacked by piranha solution, so I doubt its carbon. It only slightly flaked off with hot piranha. It did seem to be slightly affected by
concentrated sodium hydroxide, creating a slightly yellow solution full of black chunks. The NaOH did not react with the chunks either, just separated
them from the glass. Maybe it is some form of a carbon sulfur polymer?
There wasn't a fire, we just had an uncontrolled rapid oxidation event at the power plant.
|
|
Deathunter88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 513
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
Yes, you can see the effect more clearly if you pour the molten sulfur into cold water. What you get is a gooey material that is orange/red and is a
different allotrope than S8.
|
|
metalresearcher
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 737
Registered: 7-9-2010
Member Is Offline
Mood: Reactive
|
|
@woelen, did you try to dissolve the greenish crap in toluene and recrystallize it ?
On your (excellent) site I found an experiment on crystallizing sulfur: https://woelen.homescience.net/science/chem/exps/S+toluene/i...
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
https://en.wikipedia.org/wiki/Allotropes_of_sulfur, catena sulfur forms, insoluble sulfur
So recrystalisation from CS2 looks to be a good first step.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
rockyit98
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 283
Registered: 12-4-2019
Location: The Known Universe
Member Is Offline
Mood: no mood is a good mood
|
|
did you try it in inert atmosphere? I think what happening here is Oxygen atoms replacing some Sulfur atoms in S8 / S6 or any poly-sulfur thereof.
maybe that's why it happens mostly or prevalently on the surface.
"A mind is a terrible thing to lose"-Meisner
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
It's not especially complicated; hot molten sulphur is black.
This fact is well documented.
e.g.
"Just above its melting point, sulphur is a yellow, transparent, mobile liquid. Upon further heating, the viscosity of the liquid decreases gradually
to a minimum at about 157 °C (314.6 °F), but then rapidly increases, reaching a maximum value at about 187 °C (368.6 °F); between this temperature
and the boiling point of 444.6 °C (832.3 °F), the viscosity decreases. The colour also changes, deepening from yellow through dark red, and,
finally, to black at about 250 °C (482 °F). The variations in both colour and viscosity are considered to result from changes in the molecular
structure. "
From
https://www.britannica.com/science/sulfur
|
|
Morgan
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1675
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
This tiny amount of carbonaceous impurity was said to produce a black color.
"Sulfur can also vary in color and blackens upon boiling due to carbonaceous impurities. Even as little as 0.05% of carbonaceous matter darkens
sulfur."
Found as this title on Google - Chemistry of Sulfur (Z=16)
[Edited on 20-8-2021 by Morgan]
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Reading through all different replies I indeed am inclined to think that the presence of small amounts of hydrocarbons is the issue I observe. Even
after weeks, the color of strongly heated sulfur does not revert to the original yellow color. It remains olive green. Indeed, tiny amounts of very
finely divided carbon or carbon-rich black tar-like stuff can cause a strong coloration. I have seen similar things with sulfuric acid, which turned
dark brown with just a tiny drop of organic contamination in a liter of acid.
The most important reason why I believe that the coloration is due to hydrocarbon contamination is the fact that the change of color is not
reversible. All explanations, relying on allotropes of sulfur, do explain the observations at the moment of heating (e.g. turning dark red, nearly
black, getting viscous, etc.), but if there were only allotropic changes, then on cooling down and waiting for weeks I really would expect the
original color to reappear.
I have done another experiment on this, but now I heated the sulfur very carefully, so that it just melts. This leads to formation of a mobile yellow
liquid. I heated this liquid carefully, until red 'schlieren' appear and the liquid becomes more viscous. Then I stopped heating, so it never became
really hot. This sulfur, on cooling down, becomes yellow again after a few days. There still is some slight irreversible change of color, but it only
is faint. In a final experiment I did heat even more carefully, so that the red 'schlieren' did not appear and the liquid remained mobile and yellow.
Sulfur, treated that way, reverts to its original pure yellow color, albeit slightly darker. The latter can be explained, because originally it was a
powder, and now I have little lumps. Larger particles usually have a somewhat darker color.
|
|
Bedlasky
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1225
Registered: 15-4-2019
Location: Period 5, group 6
Member Is Offline
Mood: Volatile
|
|
I think, that cooling of the sulfur is still too much quick and you end up with amorphous sulfur. It slowly converts in to the cyclo-alfa-S8, but I
don't know how quick this conversion is.
[Edited on 20-8-2021 by Bedlasky]
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
It would be fairly easy to distil some sulphur and then see if the distillate went black on heating.
|
|
pneumatician
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 27-5-2013
Location: Magonia
Member Is Offline
Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **
|
|
Disable Smilies?
uh?
if you burn a man toy of plastic, how you can return the burned down plastic mass again to a man toy with same color, size...??
putting it again in the mold!!!
or search, good luck, the impurities in a 0,01% changing Sulfur color :-=
[Edited on 23-8-2021 by pneumatician]
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Distilling? Can be done, but is not easy. Boiling point of sulfur is well over 400 C, so you don't do this in a glass apparatus with
normal heating mantles and so on. You need to make some metal distilling device, with all its own engineering difficulties and the risk of
contaminating the sulfur with metal sulfides.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I think that ('disposable') borosilicate glass may be just able to boil sulfur (444.6oC)
and some member that has quartz glassware may want to try,
just to settle the question ?
An idea ...
if I seal the end of a borosilicate tube (7mm od, 5mm id) and bend the tube at about 90 degrees I could have a go at distilling sulfur.
If 'char' is produced by the boiling of the original sulfur charge
and not by heating then slowly cooling the distillate that should indicate that the charring is due to (carbon) contaminants.
If the distillate produces char then its probably an allotrope thing. (my suspicion)
Is this logical ?
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by woelen ![](images/xpblue/lastpost.gif) | Distilling? Can be done, but is not easy. Boiling point of sulfur is well over 400 C, so you don't do this in a glass apparatus with
normal heating mantles and so on. You need to make some metal distilling device, with all its own engineering difficulties and the risk of
contaminating the sulfur with metal sulfides. |
I think you are overestimating the sophistication needed.
Put some sulphur in the bottom of a test tube.
Heat it until it evaporates and then condenses in the upper part of the tube.
Then heat the stuff in the upper part of the tube and see if it goes black.
I wonder if anyone has ever made a still from gold- pretty much all the other metals react with sulphur.
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
That's right and seems doable. I'll try something like this. I once made a bent test tube for distilling white P (by strongly heating red P and then
distilling the decomposing red P as white P). A similar thing may be possible for sulfur. I'll give it a try and spend one of my cheap frosty test
tubes on it.
|
|