jenijjun
Harmless
Posts: 13
Registered: 17-11-2018
Member Is Offline
|
|
Quantitative analysis of aldehydes
Does anyone know any method how to quantitatively measure the amount of an aldehyde in a sample?
|
|
Antigua
Hazard to Others
Posts: 156
Registered: 27-9-2020
Member Is Offline
|
|
Tollens test and check the weight of silver precipitated. Or bisulfite adduct and calculate on it's basis.
|
|
unionised
International Hazard
Posts: 5130
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Or reaction with DNPH.
If three's lots of aldehyde, you can weigh the derivative.
If there are only traces, you can measure it by HPLC or some such.
|
|
karlos³
International Hazard
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Second the DNP.
Bisulfite adducts can have a certain solubility even in water.
|
|
Bedlasky
International Hazard
Posts: 1246
Registered: 15-4-2019
Location: Period 5, group 6
Member Is Offline
Mood: Volatile
|
|
Water soluble aldehydes (C1-C4) can be easily determined by acidimetry. You need 5% sodium sulfite solution neutral to thymolphtalein. Make a stock
solution of your aldehyde, pipette some of it in to the titration flask, add thymol blue and add 0,1M NaOH until indicator turns blue. Then add 10 ml
of 5% Na2SO3 solution. Aldehyde react with sodium sulfite according to equation:
Na2SO3 + RCHO + H2O --> RCHO.NaHSO3 + NaOH
NaOH formed in reaction is titrated by 0,1M HCl until indicator become colourless. I tried this method on formaldehyde and propionaldehyde and it
worked well. If you don't have thymolphtalein you can use phenolphtalein.
I also found little bit different method which can be applied even on insoluble aldehydes:
https://sci-hub.se/https://pubs.acs.org/doi/pdf/10.1021/ac60...
Hydroxylamine method is another option, but it is more time consuming:
https://sci-hub.se/https://pubs.acs.org/doi/10.1021/ja01304a...
[Edited on 6-8-2021 by Bedlasky]
[Edited on 7-8-2021 by Bedlasky]
|
|
unionised
International Hazard
Posts: 5130
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
In my experience the sulphite/ thymolphthalein titration sucked badly. Phenolphthalein was even worse.
Even following the pH with a meter it was hard to determine the end point.
The titration with hydroxylamine/ hydroxylammonium chloride was much better.
The best precision I could get was by gravimetry using a modification of Tollens reagent.
You dissolve silver oxide in an aqueous solution of tertiary butylamine (this has the great advantage that it doesn't produce explosive silver
compounds on standing.)
Add a weighed amount of your aldehyde solution and when the reaction finished, weigh the silver produced.
The big advantage to DNPH and HPLC is that it lets you analyse a mixture of aldehydes (and, of course it offers much better sensitivity than
weighing).
It's not great with unsaturated aldehydes like acrolein.
And the derivatives are pretty colours.
The big disadvantage is that the stuff is potentially explosive.
My view on the ISO committee which decided that the best thing to do with it was to add perchloric acid is probably unprintable.
|
|
Bedlasky
International Hazard
Posts: 1246
Registered: 15-4-2019
Location: Period 5, group 6
Member Is Offline
Mood: Volatile
|
|
What problems did you have? Not enough sharp end point? I never tried it with indicators. I used potentiometric determination and this surely work
without problems. You adjust pH to 9,5 and titrate back to 9,5.
|
|
unionised
International Hazard
Posts: 5130
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
It's 15 or 20 years since I did this but as I recall, the "fade in" from clear to blue took about 2 ml of NaOH soln.
I also looked at the method using an alkaline solution of a mercury complex- reduced to metallic mercury- but I didn't see any advantage over silver,
and I didn't fancy the toxicity.
Other colorimetric options are "purpald"
https://www.sigmaaldrich.com/GB/en/product/aldrich/162892
and 3-methyl-2-benzothiazolinone hydrazone hydrochloride
The N methyl derivative of DNPH is interesting- you don't get the same problems of cis/ trans isomers with aldehydes and unsymmetrical ketones.
I don't know if MDNPH is on the market as a reagent.
|
|